Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE HOOD SUB-ASSEMBLY


2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type)
  1. Remove the 4bolts, then remove the engine under cover No.1.



4. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type, Regular Cab)
  1. Remove the 4 bolts, then remove engine cover No.2.



5. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the 4 bolts, then remove the engine under cover No. 1. (PRE RUNNER AND 4WD TYPE)



    G038197E01
  1. Install a vinyl hose onto the radiator side.



    G038198E01
  1. Install a vinyl hose onto the engine side.



    G038199E01
  1. Loosen the engine drain plug.

  1. Loosen the radiator drain plug.

  1. Remove the radiator cap and drain coolant.

  1. Drain the coolant from the reservoir tank.



6. REMOVE BATTERY


7. REMOVE BATTERY TRAY


8. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G038206E01
  1. Disengage the 9 clips, then remove the radiator support to frame seal LH.



9. REMOVE FAN SHROUD


A086838E01
  1. Loosen the 4 nuts shown in the illustration.

  1. Remove the fan and generator V belt.



    G038207E01
  1. Disconnect the radiator reserve tank hose from the radiator.



    G038208E01
  1. Disconnect the oil cooler inlet and outlet hoses from the fan shroud. (for Automatic Transmission)



    G038209E01
  1. Remove the 2 bolts shown in the illustration.



    G038210E01
  1. Remove the 4 nuts, then remove the fan shroud and fan with fluid coupling together.

    NOTICE:
    Make sure that the fan shroud and fan with fluid coupling do not make any contact with the radiator when they are removed.



    G038211E01
  1. Remove the fan pulley.



10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


G037934E01
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the wire harness clamp.

  1. Loosen the hose clamp bolt, then disconnect the air cleaner hose No. 1.

  1. Disconnect the 2 air cleaner clamps.

  1. Remove the air cleaner cap together with the air cleaner hose No. 1.



11. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


12. REMOVE AIR CLEANER CASE
  1. Remove the 3 bolts, then remove the air cleaner case.



13. SEPARATE VANE PUMP


G037555E01
  1. Disconnect the vane pump connector.

  1. Remove the 2 bolts, then separate the vane pump.

    HINT:
    Do not disconnect the hose. Hang the vane pump with a rope.



14. REMOVE NO. 2 RADIATOR HOSE


15. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)


G038205E01
  1. Remove the bolt shown in the illustration.



    G038234E01
  1. Disconnect the compressor and magnetic clutch connector.

  1. Remove the 4 bolts, then separate the compressor and magnetic clutch.

    HINT:
    Do not disconnect the hose. Hang the vane pump with a rope.



16. REMOVE RADIATOR HOSE INLET


17. SEPARATE WATER HOSE SUB-ASSEMBLY


G038551E01
  1. Separate the water hoses.



18. DISCONNECT FUEL HOSE


G037900E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



19. DISCONNECT NO. 2 FUEL HOSE


G037902E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



20. SEPARATE FUEL VAPOR FEED HOSE ASSEMBLY


G038552E01
  1. Disconnect the fuel vapor feed hose.



21. DISCONNECT NO. 1 AIR INJECTION HOSE


G038553E01
  1. Disconnect the No.1 air injection hose.



22. DISCONNECT ENGINE WIRE
  1. Disconnect the connector from the ECM, then pull the engine wire harness to the compartment side.

    NOTICE:
    Do not forcibly pull the wire harness to the engine compartment side.

  1. Disconnect all wire harnesses and connectors in the engine room.



23. REMOVE EXHAUST PIPE ASSEMBLY TAIL
  1. Remove the 2 bolts and 2 nuts.

  1. Remove the exhaust pipe tail from the 4 exhaust pipe supports.

  1. Remove the gasket from the exhaust pipe front.



24. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the exhaust pipe front from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold.



25. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
Transmission
See page
R155
Click here
R155F
Click here


26. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


27. REMOVE ENGINE ASSEMBLY


G037564E03
  1. Install the engine hanger with the bolt.

    Torque:
    42 N*m{ 420 kgf*cm , 30 ft.*lbf }

    Part No:
    Part Name
    Part No.
    Engine hanger
    12281-75040
    Bolt
    91552-A1020

    NOTICE:
    Be sure to use the bolts when installing the engine hanger.



    G038554E01
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Remove the 4 bolts and 4 nuts.

  1. Lift the engine out of the vehicle slowly and carefully by operating the engine sling device and chain block.

    NOTICE:
    Make sure that no wires, hoses or cables are connected to the engine.



28. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


29. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


30. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


G038108E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E03
  1. Remove the 10 bolts, then remove the flywheel.



31. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


    G038108E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A099868E05
  1. Remove the 10 bolts, drive plate spacer rear, drive plate and ring gear and drive plate spacer front.



32. REMOVE REAR END PLATE
  1. Remove the 2 bolts, then remove the rear end plate.



33. REMOVE INTAKE AIR CONNECTOR


G037694E01
  1. Disconnect the pressure sensor connector.

  1. Disengage the wire harness clamp.

  1. Disconnect the vacuum hose.



    G037695E01
  1. Disconnect the No. 2 ventilation hose.



    G037696E01
  1. Disconnect the vacuum hose.



    G037697E01
  1. Loosen the 2 hose clamp bolts.

  1. Remove the 3 bolts, then remove the intake air connector.



34. REMOVE FUEL HOSE


G037900E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



35. REMOVE NO. 2 FUEL HOSE


G037902E01
  1. Pull the checker of the fuel hose upward.

  1. Pinch the detaching switch of the fuel hose connector and pull out the fuel hose.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

    3. G037901E01
      Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel hose.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



36. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


G037698E01
  1. Disconnect the water by-pass hose.

  1. Disconnect the No. 2 water by-pass hose.

  1. Disconnect the throttle motor connector.



    G037699E01
  1. Remove the 2 bolts and 2 nuts, then remove the throttle with motor body.



    G037700E01
  1. Remove the gasket from the intake manifold.



37. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET


G037704E01
  1. Disconnect the fuel vapor feed hose from the VSV.



    G037705E01
  1. Disconnect the vacuum hose.



    G037706E01
  1. Remove the bolt, then remove the clamp bracket.



    G039454E01
  1. Disconnect the water by-pass hose No. 2.



    G039455E01
  1. Disconnect the ventilation hose No. 3.



    G037709E01
  1. Disconnect the VSV connector.

  1. Disengage the engine wire harness clamp.

  1. Disconnect the compressor magnetic clutch connector. (w/ AIR CONDITIONING)

  1. Disengage the wire harness clamp.

  1. Remove the bolt and harness clamp bracket.



    G037710E01
  1. Disconnect the 3 connectors.

  1. Remove the nut shown in the illustration.

  1. Disconnect the engine wire harness from the relay block.



    G037711E01
  1. Remove the 5 bolts and 2 nuts, then remove the intake manifold.



38. REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)


G037912E02
  1. Remove the 5 bolts, then remove the idle pulley with bracket.



39. REMOVE ENGINE WIRE


40. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY


41. REMOVE OIL LEVEL GAGE GUIDE


G037556E01
  1. Remove the bolts, then remove the oil level gage guide.



42. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET


G038555E01
  1. Remove the 4 bolts, then remove the engine mounting bracket front No. 1 LH with engine mounting insulator front.



43. REMOVE THERMOSTAT


    G038201E01
  1. Remove the thermostat from the timing chain cover.



44. REMOVE FUEL INJECTOR ASSEMBLY


G037895E01
  1. Pull the 4 fuel injectors out of the fuel delivery pipe.



45. REMOVE KNOCK SENSOR


G037712E01
  1. Disconnect the knock control sensor connector.

  1. Remove the bolt, then remove the knock control sensor.



46. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


G037562E01
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor.



47. REMOVE NO. 1 WATER BY-PASS PIPE


G035420E01
  1. Remove the 2 nuts, then remove the water by-pass pipe No. 1.



48. REMOVE VENTILATION PIPE


G038556E01
  1. Remove the bolts, then remove the ventilation pipe.



49. REMOVE IGNITION COIL ASSEMBLY
(Click here)


50. REMOVE SPARK PLUG


51. REMOVE GENERATOR ASSEMBLY


G038188E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the generator wire.

  1. Disconnect the generator connector.



    G038189E01
  1. Remove the 2 bolts, then remove the generator.



52. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


A099635E01
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



53. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    G038212E01
  1. Remove the 3 bolts, then remove the V-ribbed belt tensioner.



54. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


G037935E01
  1. Remove the 5 bolts, then remove the exhaust manifold heat insulator No. 1.



55. REMOVE AIR SWITCHING VALVE ASSEMBLY


G037938E01
  1. Disconnect the vacuum hose.

  1. Disconnect the air switching valve connector.



    G037939E01
  1. Remove the 2 nuts, then remove the air switching valve.

  1. Remove the gasket.



56. REMOVE EXHAUST MANIFOLD


G038543E01
  1. Remove the 8 nuts, then remove the exhaust manifold.



57. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


G038557E01
  1. Remove the 4 bolts, then remove the engine mounting bracket front No. 1 together with the engine mounting insulator front.



58. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
(Click here)