Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type)

DTC    B1797    Calibration Malfunction

for Preparation Click here


DESCRIPTION

  1. DTC B1797 is output when the following condition is met:
    1. Zero point calibration is performed when the conditions for the calibration are not satisfied.
    2. Zero point calibration has failed.

Condition for the zero point calibration: 
Item
Condition
DTC
Not recorded.
Front passenger seat occupant.
Vacant
Front passenger side buckle switch.
OFF (The seat belt is not fastened)
ECU temperature
0 to 46°C (32 to 114.8°F)
Filtered pressure
38 to 75 count

DTC No.
DTC Detecting Condition
Trouble Area
B1797
  1. Zero point calibration is performed when the conditions for the calibration are not satisfied.
  2. Zero point calibration has failed.
  1. There is no malfunction if this DTC is not output again after performing occupant classification system zero point calibration.
  2. Occupant classification sensor (front seat cushion assembly)

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting for the supplemental restraint system, check the DTCs stored in the occupant classification ECU. When DTC B1797 is output, perform troubleshooting for the DTC.
  2. Use the intelligent tester to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 10 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1797 is output.

    HINT:
    DTCs other than B1797 may be output at this time, but they are not related to this check.



NO
END
YES


2.READ VALUE OF DATA LIST (SPECIFIED CONDITION FOR ZERO POINT CALIBRATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON position.

  1. Using the intelligent tester, read the DATA LIST (Click here).


Item
Measurement Item/ Range (Display)
Normal Condition
Specified Condition for Zero Point Calibration
RELATIVE PRESS
Pressure sensor output/
Min.: 0
Max.: 255
0 to 210
(reference value)
0 to 2
THERMISTOR TEMP
Thermistor temperature output/
Min.: -40°C (-40°F)
Max.: 90°C (194°F)
-40 to 85°C
(-40 to185°F)
3 to 40°C
(36 to 104°F)
#PRESENT CODES
Number of present trouble codes/
Min.: 0
Max.: 255
0
0
#PAST CODES
Number of past trouble codes/
Min.: 0
Max.: 255
0
0

RESULT:

Result
Proceed to
All items correspond to the range of specified condition for zero point calibration.
A
THERMISTOR TEMP does not correspond to the range of specified condition for zero point calibration.
B



B
Go to step 6
A


3.CHECK DTC

HINT:
Check that the zero point calibration is completed normally. If either of the following condition is met, DTC B1797 will be output (Refer to INITIALIZATION: Click here).
  1. Zero point calibration is performed when the the calibration conditions are not satisfied.
  2. Zero point calibration has failed.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1797 is not output.


NEXT


4.PERFORM ZERO POINT CALIBRATION
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

  1. Turn the ignition switch to the OFF position.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    If DTC is not cleared at this time, past DTC will remain.


NEXT


5.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1797 is not output.

    HINT:
    DTCs other than B1797 may be output at this time, but they are not related to this check.


NEXT

END 

6.REPLACE FRONT SEAT CUSHION ASSEMBLY (WITH OCCUPANT CLASSIFICATION SENSOR AND SENSOR)
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat cushion assembly (with occupant classification sensor and ECU) (Click here).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, check the DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.


NEXT

END