Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P219A    Bank 1 Air-Fuel Ratio Imbalance

DTC    P219B    Bank 2 Air-Fuel Ratio Imbalance

for Preparation Click here


DESCRIPTION

Refer to P0300 .
Refer to P2195, P2197 .

DTC No.
DTC Detection Condition
Trouble Area
P219A
P219B
The difference in air fuel ratios between the cylinders exceeds the threshold.
  1. Fuel injector assembly
  2. Air intake system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor (bank 1, 2 sensor 1)
  7. ECM

MONITOR DESCRIPTION

  1. Fuel System Air fuel Ratio Cylinder Imbalance Monitor
    The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leaks in the intake or exhaust system, etc.
    When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.
  1. Air Fuel Ratio Sensor Monitoring Method
    When the system detects a difference in air fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.
  1. Crankshaft Position Sensor Monitoring Method
    The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air fuel ratios between the cylinders, which it determines to be a problem.

MONITOR STRATEGY


Related DTCs
P219A: Air fuel ratio cylinder imbalance monitor (bank 1)
P219B: Air fuel ratio cylinder imbalance monitor (bank 2)
Required Sensors/Components (Main)
Air fuel ratio sensor
Crankshaft position sensor
Required Sensors/Components (Related)
Mass air flow meter sub-assembly
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds: Air fuel ratio sensor monitoring method
30 seconds: Crankshaft position sensor monitoring method
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
P0010, P0020 (Camshaft timing oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT System - retard)
P0016, P0018 (VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333 (Knock control sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0412, P0418, P1613 (Secondary air injection system control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary air injection system)
P0500 (Vehicle speed sensor)

Air Fuel Ratio Sensor Monitoring Method 
Air fuel ratio sensor status
Activated
Engine speed
1200 rpm or higher, and less than 2400 rpm
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Fuel system status
Closed loop
Mass air flow
36 gm/sec or more, and less than 55 gm/sec

Crankshaft Position Sensor Monitoring Method 
Vehicle speed
Less than 3 km/h (1.875 mph)
Engine speed
400 rpm or higher, and less than 1050 rpm (Automatic Transmission)
550 rpm or higher, and less than 1050 rpm (Manual Transmission)
Engine coolant temperature
75°C (167°F) or higher
Air fuel ratio sensor status
Activated
Battery voltage
11 V or higher
Fuel system status
Closed loop

TYPICAL MALFUNCTION THRESHOLDS


Air Fuel Ratio Sensor Monitoring Method 
Air fuel ratio sensor monitoring method criteria (rich side imbalance)
0.085 or more (bank 1)
0.095 or more (bank 2)

Crankshaft Position Sensor Monitoring Method 
Crankshaft position sensor monitoring method criteria (lean side imbalance)
1 or more

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A240420E07

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N (Neutral).

  7. Drive the vehicle at 60 km/h (37 mph) or higher for 2 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    It is acceptable to turn electrical loads on while driving.

  8. Idle the engine for 2 minutes or more [C].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N (Neutral).

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Drive the vehicle at less than 30 km/h (18.64 mph) for 5 seconds or more [E].
  12. Accelerate the vehicle from 30 to 60 km/h (18.64 to 37 mph) over a period of approximately 10 to 20 seconds.

    HINT:
    Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (18.64 to 37 mph).

  13. Drive the vehicle at 60 km/h (37 mph) or more for 5 seconds or more [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Drive the vehicle at less than 30 km/h (18.64 mph) for 5 seconds or more [G].
  15. Accelerate the vehicle from 30 to 60 km/h (18.64 to 37 mph) over a period of approximately 10 to 20 seconds.

    HINT:
    Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (18.64 to 37 mph).

  16. Drive the vehicle at 60 km/h (37 mph) or more for 5 seconds or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  17. Repeat steps [G] through [H] above at least 2 times [I].
  18. Idle the engine for 1 minute or more [J].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N (Neutral).

  19. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
  20. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  21. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  22. Input the DTC: P219A or P219B.
  23. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  24. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  6. Refer to A/F Sensor Determination (worst value) #1, A/F Sensor Determination (worst value) #2, Engine Speed Fluctuation Avg (worst value) #1 to #6, Cylinder #1 to #6 Misfire Count, Short FT #1, Short FT #2, Long FT #1 and Long FT #2 in the Data List / Active Test (Click here).

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P219A AND/OR P219B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P219A and/or P219B is output
    A
    DTC P219A and/or P219B and other DTCs are output
    B

    HINT:
    If any DTCs other than DTC P219A and/or P219B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Freeze Frame Data Items for DTC P219A or P219B
    1. Vehicle Speed
    2. Engine Speed
    3. Calculate Load
    4. Accelerator Idle Position
    5. Short FT #1 or #2
    6. Long FT #1 or #2
    7. Cylinder #1 Misfire Count to Cylinder #6 Misfire Count
    8. A/F Sensor Determination (worst value) #1 or #2
    9. Engine Speed Fluctuation Avg (worst value) #1 to #6

    HINT:
    When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.


    DTC stored during idling
    It is possible to conclude that the problem was detected due to a "lean imbalance" (detected using crankshaft speed variation).
    DTC stored while vehicle being driven
    It is possible to conclude that the problem was detected due to a "rich imbalance" (detected using the air fuel ratio sensor).


NEXT


3.READ VALUE USING TECHSTREAM (MONITOR RESULT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    HINT:
    1. If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #6 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.
    2. Perform inspections while focusing on the cylinder whose misfire count has increased.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Fuel System / Details / A/F SENSOR DETERMINATION B1, A/F SENSOR DETERMINATION B2, ENGINE SPEED FLUCTUATION AVERAGE B1 and ENGINE SPEED FLUCTUATION AVERAGE B2.

  1. Check the Test Result (A/F SENSOR DETERMINATION B1, A/F SENSOR DETERMINATION B2, ENGINE SPEED FLUCTUATION AVERAGE B1 and ENGINE SPEED FLUCTUATION AVERAGE B2).

    Result 
    Result
    Proceed to
    A/F SENSOR DETERMINATION is Fail
    A
    A/F SENSOR DETERMINATION and ENGINE SPEED FLUCTUATION AVERAGE are Fail
    B
    ENGINE SPEED FLUCTUATION AVERAGE is Fail
    B*

    HINT:
    1. When the results of A/F SENSOR DETERMINATION and ENGINE SPEED FLUCTUATION AVERAGE are both Pass, drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern again.
      If both results are still Pass, proceed to step 4.
    2. *: Perform inspections while focusing on the cylinder whose engine speed fluctuation value ("Engine Speed Fluctuation Avg (worst value) #1" to "Engine Speed Fluctuation Avg (worst value) #6") was the largest.



B
Go to step 6
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N (Neutral).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #6 Misfire Count.

    HINT:
    When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Air Induction System).

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #6 Misfire Count") while decreasing the injection volume in 5% increments.

    NOTICE:
    Do not decrease the injection volume by more than 20%.

    Result:
    The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.


NEXT


5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


6.CHECK AIR INTAKE SYSTEM
  1. Check the air intake system for vacuum leaks.

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the cylinder causing the imbalance .



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test (Click here).

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Sparks jump across electrode gap.



NG
Go to step 15
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
A167963E27
  1. Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F6-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F10-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the fuel injector assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    F5-2 - E12-6 (#10)
    Always
    Below 1 Ω
    F6-2 - E12-1 (#20)
    Always
    Below 1 Ω
    F7-2 - E12-7 (#30)
    Always
    Below 1 Ω
    F8-2 - E12-2 (#40)
    Always
    Below 1 Ω
    F9-2 - E12-8 (#50)
    Always
    Below 1 Ω
    F10-2 - E12-3 (#60)
    Always
    Below 1 Ω
    F5-2 or E12-6 (#10) - Body ground
    Always
    10 kΩ or higher
    F6-2 or E12-1 (#20) - Body ground
    Always
    10 kΩ or higher
    F7-2 or E12-7 (#30) - Body ground
    Always
    10 kΩ or higher
    F8-2 or E12-2 (#40) - Body ground
    Always
    10 kΩ or higher
    F9-2 or E12-8 (#50) - Body ground
    Always
    10 kΩ or higher
    F10-2 - E12-3 (#60) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK FOR CAUSE OF FAILURE
  1. If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.

  1. Check the intake valve for deposits.

    HINT:
    As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head and check the intake valve.


NEXT


14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the pending DTCs.

    Result:
    DTC P219A and/or P219B is not output.


NEXT

END 

15.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF CYLINDER CAUSING IMBALANCE
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test .

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Sparks jump across electrode gap.



NG
Go to step 16
OK

REPLACE SPARK PLUG (Click here)  

16.CHANGE TO NORMAL IGNITION COIL ASSEMBLY AND CHECK SPARK OF CYLINDER CAUSING IMBALANCE
  1. Change the ignition coil assembly to an ignition coil assembly that functions normally.

  1. Perform a spark test .

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)