Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2444    Secondary Air Injection System Pump Stuck On Bank1

DTC    P2445    Secondary Air Injection System Pump Stuck Off Bank1

for Preparation Click here


DESCRIPTION

Refer to P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2444
Both of the following conditions are met for 7 seconds (2 trip detection logic):
(a) Engine is running
(b) Secondary air injection pressure is 3 kPa (22.5 mmHg) or more when secondary air injection is OFF
  1. Short in air pump assembly circuit
  2. Open or short in pressure sensor circuit
  3. Pressure sensor (built into air switching valve)
  4. Air injection control driver
  5. ECM
P2445
Both of the following conditions are met for 7 seconds (2 trip detection logic):
(a) Engine is running
(b) Secondary air injection pressure is less than 1 kPa (7.5 mmHg) when secondary air injection is ON
  1. Air pump assembly
  2. Open in air pump assembly circuit
  3. Air injection system piping
  4. Pressure sensor (built into air switching valve)
  5. Open or short in pressure sensor circuit
  6. Air injection control driver
  7. ECM

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
  1. The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump.
  2. The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump.
Example:
  1. DTC P2444 mainly indicates a malfunction in which the air pump is stuck on.
  2. DTC P2445 mainly indicate a malfunction in which the air pump is stuck off.

MONITOR STRATEGY


Related DTCs
P2444: Air pump stuck ON
P2445: Air pump stuck OFF
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation)
P1340 (Camshaft position sensor)
P1613 (Secondary air injection driver)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Front oxygen/Air fuel ratio sensor)
P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor)
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (338 mmHg) or more
Engine
Running
Pressure pattern check during secondary air injection ON*1
Completed
Pressure pattern check during secondary air injection OFF*2
Completed
Pressure change check: secondary air injection ON*3
Completed
Pressure pulsation check: secondary air injection OFF*4
Completed
Air injection control driver failure (open/short or out of range)
Not detected
Secondary air injection system pressure sensor failure (open/short or out of range)
Not detected

*1: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
5 seconds or more
Air pump
ON
Air switching valve
Open
Engine speed
Less than 3750 rpm
Engine speed
680 rpm or more
Intake air amount per liter
Less than 100 gm/sec
Time after engine start
5 second or more

*2: Pressure pattern check during secondary air injection OFF
-
Time after secondary air injection starts operation
10 seconds or more
Air pump
OFF
Air switching valve
Closed
Engine speed
Less than 3000 rpm
Secondary air injection monitor during secondary air injection ON
Completed
Engine load
7 to 60%
Time after engine start
5 seconds or more

*3: Pressure change check: secondary air injection ON
-
Secondary air injection
Operating
Air pump
ON
Air switching valve (bank 1)
Open
Air switching valve (bank 2)
Closed
Secondary air injection system pressure sensor failure (open/short or out of range)
Not detected
Intake air amount per liter
Less than 15 gm/sec

*4: Pressure pulsation check: secondary air injection OFF
-
Pressure change check: secondary air injection ON
Completed
Pressure pulsation check: secondary air injection OFF
Not completed
Air pump
ON
Time after air switching valve (bank 1) closes
0.3 seconds or more
Air switching valve (bank 2)
Open
Engine speed
Less than 5000 rpm

TYPICAL MALFUNCTION THRESHOLDS


P2444: Air Pump is Stuck ON 
One of the following conditions is met
(a) or (b)
(a) Condition 1 (secondary air injection OFF)
-
(b) Condition 3 (secondary air injection OFF)
-

P2445: Air Pump is Stuck OFF 
One of the following conditions is met
(a) or (b)
(a) Condition 2 (secondary air injection ON)
-
(b) Condition 4 (secondary air injection ON)
-

Secondary Air Injection ON (Condition 1) 
Both of the following conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or more
Secondary air injection pressure
1 kPa (7.5 mmHg) or more

Secondary Air Injection ON (Condition 2) 
Both of the following conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or more
Secondary air injection pressure
Less than 1 kPa (7.5 mmHg)

Secondary Air Injection ON (Condition 3) 
Both of the following conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Less than 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
1 kPa (7.5 mmHg) or more

Secondary Air Injection ON (Condition 4) 
Both of the following conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Less than 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
Less than 1 kPa (7.5 mmHg)

Secondary Air Injection OFF (Condition 1) 
Both of the following conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or more
Secondary air injection pressure
3 kPa (22.5 mmHg) or more

Secondary Air Injection OFF (Condition 2) 
Both of the following conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or more
Secondary air injection pressure
Less than 3 kPa (22.5 mmHg)

Secondary Air Injection OFF (Condition 3) 
Both of the following conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Less than 10 kPa (75 mmHg)
Secondary air injection pressure
3 kPa (22.5 mmHg) or more

Secondary Air Injection OFF (Condition 4) 
Both of the following conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Less than 10 kPa (75 mmHg)
Secondary air injection pressure
Less than 3 kPa (22.5 mmHg)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Read pending DTCs.

    OK:
    No pending DTC is output.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. After Secondary Air Injection Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2444 or P2445.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump and air switching valve and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure Condition in Secondary Air Injection System Case 1 
Air Pump
ON
Air Switching Valve
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Below 3 kPa (22.5 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3 
Air Pump
ON
Air Switching Valve
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4 
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Below 3 kPa (22.5 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5 
Air Pump
ON
Air Switching Valve
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Below 3 kPa (22.5 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7 
Air Pump
ON
Air Switching Valve
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8 
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Below 3 kPa (22.5 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump assembly is assumed to be ON and if it alternates sharply, the air switching valve assembly is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

HINT:
  1. In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the air switching valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa (112.5 to 187.5 mmHg)).
  2. In case 1, the average pressure is approximately 3 to 11 kPa (22.5 to 82.5 mmHg). The value of 1 kPa (7.5 mmHg) indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while secondary air injection Operating:
Air Pump ON, Air Switching Valve Open
Detected Condition while secondary air injection not Operating:
Air Pump OFF, Air Switching Valve Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
Air switching valve stuck open
P2440
and/or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
Case 2
Case 8
Air pump stuck OFF
P2445
Case 3
Case 8
Air switching valve stuck closed
P2441
and/or
P2443
Case 1
Case 5
Air switching valve stuck open and air pump stuck ON
P2440 and/or P2442
and
P2444
Case 2
Case 6
Air switching valve stuck open and air pump stuck OFF
P2440 and P2442
and
P2445
Case 3
Case 7
Air switching valve stuck closed and air pump stuck ON
P2441 and P2443
and
P2444
Case 4
Case 8
Air switching valve stuck closed and air pump stuck OFF
P2441 and P2443
and
P2445

HINT:
  1. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1 CLOSE, ASV2 CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.
    8. Perform the secondary air injection system forced operation while the engine is idling.
    9. Check that the air pump assembly (AIR PUMP), air switching valve assembly (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

      Standard:

      Techstream Operation
      Air Pump Assembly
      Air Switching Valve Assembly
      Pressure*1
      Pulsation*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      1 kPa (7.5 mmHg) or higher
      1.25 kPa (9.3 mmHg) or higher
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Below 3 kPa (22.5 mmHg)
      Below 10 kPa (75 mmHg)

      *1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa (7.5 mmHg) or higher when the secondary air injection system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
    10. Turn the ignition switch off.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 OR P2445)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P2444 or P2445 is output
    A
    DTC P2444 or P2445 and P0418 are output
    B
    DTC P2444 or P2445 and other DTCs (except P0418) are output
    C

    HINT:
    If any DTCs other than P0418, P2444 and/or P2445 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE

C
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Check that the air pump assembly (AIR PUMP), air switching valve assembly (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

    Standard:

    Techstream Operation
    Air Pump
    Air Switching Valve
    Pressure*
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    1 kPa (7.5 mmHg) or higher [A]
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Below 3 kPa (22.5 mmHg) [B]

    *: Average pumping pressure. The pressure should be 1 kPa (7.5 mmHg) or higher when the secondary air injection system operates.

    Standard:
    The pressures for [A] and [B] should differ by 1 kPa (7.5 mmHg) or more.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Read pending DTCs.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Result 
    Result
    Proceed to
    DTC P2444 or P2445 is output
    A
    DTC is not output
    B

  1. Turn the ignition switch off.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).

  1. Check the pressure displayed on the Techstream.

    Standard pressure:
    45.63 to 135 kPa (342 to 1013 mmHg)

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE ASSEMBLY (Click here)
OK


5.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

A254592

  1. Check that all the pipes and hoses between the air pump and air switching valve are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    Secondary air injection system piping has no blockages or damage.



NG
REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING
OK


6.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A221587E07
  1. Disconnect the air injection control driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)
    A7-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR INJECTION DRIVER - BATTERY)
OK


7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E10-23 (AIRP) - A7-4 (SIP)
    Always
    Below 1 Ω
    E10-23 (AIRP) or A7-4 (SIP) - Body ground
    Always
    10 kΩ higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT AIR PUMP ASSEMBLY
  1. Inspect the air pump assembly (Click here).



OK
Go to step 11

NG
Go to step 9

9.REPLACE AIR PUMP ASSEMBLY
  1. Replace the air pump assembly (Click here).


NEXT


10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Read pending DTCs.

    OK:
    DTC is not output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Turn the ignition switch off.



NG
Go to step 11
OK

END 

11.PERFORM ACTIVE TEST USING TECHSTREAM


    A229922E24
  1. Disconnect the air injection control driver connector.

  1. Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A7-3 (SIV) - A7-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A7-3 (SIV) - A7-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. Turn the ignition switch off.



    A229922E25
  1. Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A7-4 (SIP) - A7-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A7-4 (SIP) - A7-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. Turn the ignition switch off.



NG
REPLACE ECM (Click here)
OK


12.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Read pending DTCs.

    OK:
    No pending DTC is output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Turn the ignition switch off.



NG
REPLACE ECM (Click here)
OK

END