Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

DTC    P103D    A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

HINT:
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte though the alumina, and therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide, hydrocarbon and nitrogen oxide components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E09


A171616E05

HINT:
  1. When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
  2. Although the DTC titles say the oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  3. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


A255442E03


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air fuel ratio sensor heater current less than 0.8 A (1 trip detection logic)
  1. Open in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  3. A/F HEATER relay
  4. ECM
P0032
P0052
Air fuel ratio sensor heater current fail
(1 trip detection logic)
  1. Short in air fuel ratio sensor (bank 1, 2 sensor 1) heater circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  3. A/F HEATER relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is not operating
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate, as a result, the ECM is unable to regulate air-fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0031: Air fuel ratio sensor (bank 1 sensor 1) heater open/short (Low electrical current)
P0032: Air fuel ratio sensor (bank 1 sensor 1) heater open/short (High electrical current)
P0051: Air fuel ratio sensor (bank 2 sensor 1) heater open/short (Low electrical current)
P0052: Air fuel ratio sensor (bank 2 sensor 1) heater open/short (High electrical current)
P101D: Air fuel ratio sensor (bank 1 sensor 1) heater performance
P103D: Air fuel ratio sensor (bank 2 sensor 1) heater performance
Required Sensors/Components (Main)
Air fuel ratio sensor (bank 1,2 sensor 1) heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second: P101D and P103D
10 seconds: P0031 and P0051
10.24 seconds: P0032 and P0052
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0031 and P0051 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Active heater off control
Not operating
Active heater on control
Not operating
Air fuel ratio sensor heater performance fail (P101D, P103D)
Not detected
Heater output duty cycle
30% or higher

P0032 and P0052 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Heater output duty cycle
Higher than 0%
Active heater off control
Not operating
Active heater on control
Not operating

P101D and P103D 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Air fuel ratio sensor heater low current fail (P0031, P0051)
Not detected
Heater output duty cycle
10% or higher, and less than 60%
Heater on current
0.8 A or higher
Active heater off control
Not operating
Active heater on control
Not operating

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051 
Air fuel ratio sensor heater ON current
Less than 0.8 A

P0032 and P0052 
Both of the following conditions are met
-
Air fuel ratio sensor heater output
ON
Hybrid IC high current limiter monitor input
Fail

P101D and P103D 
Both of the following conditions are met
-
Air fuel ratio sensor heater OFF current
Higher than 11 A
Hybrid IC high current limiter monitor input
Fail

COMPONENT OPERATING RANGE


P0031 and P0051 
Air fuel ratio sensor heater current
0.8 A or more

P0032 and P0052 
Both of the following conditions are met
-
Air fuel ratio sensor heater output
ON
Hybrid IC high current limiter monitor input
Pass

P101D and P103D 
Air fuel ratio sensor heater ON current
11 A or less

CONFIRMATION DRIVING PATTERN


A198819E18

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A254616E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. Refer to "Data List / Active Test" [A/F Heater Duty #1, A/F Heater Duty #2] (Click here).
  6. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
  7. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
A150242E42
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    A5-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *b
    Bank 1
    *c
    Bank 2



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A4-1 (HA1A) - E12-17 (HA1A)
    Always
    Below 1 Ω
    A5-1 (HA2A) - E12-19 (HA2A)
    Always
    Below 1 Ω
    A4-1 (HA1A) or E12-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    A5-1 (HA2A) or E12-19 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR 103D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0031, P0032, P0051, P0052, P101D or P103D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT A/F HEATER RELAY
B016200E02
  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE A/F HEATER RELAY
OK


6.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F HEATER RELAY)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A4-2 (+B) - 3 (A/F HEATER relay holder)
    Always
    Below 1 Ω
    A5-2 (+B) - 3 (A/F HEATER relay holder)
    Always
    Below 1 Ω
    A4-2 (+B) or 3 (A/F HEATER relay holder)- Body ground
    Always
    10 kΩ or higher
    A5-2 (+B) or 3 (A/F HEATER relay holder) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)