Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

DTC    C1275    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1413    Front Speed Sensor RH Output Malfunction

DTC    C1414    Front Speed Sensor LH Output Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).

DTC Code
DTC Detection Condition
Trouble Area
C1275
C1276
Stored only during test mode.
  1. Front speed sensor RH/LH
  2. Front speed sensor rotor RH/LH (Front axle with ABS rotor bearing assembly RH/LH)
C1413
C1414
One of the following conditions is met:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Skid control sensor wire
  3. Speed sensor circuit
  4. Front speed sensor rotor RH/LH (Front axle with ABS rotor bearing assembly RH/LH)
  5. Skid control ECU (Brake actuator assembly)

HINT:
  1. DTCs C1413 and C1275 are for the front speed sensor RH.
  2. DTCs C1414 and C1276 are for the front speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1405 and C1406 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform calibration (Click here).
  2. Check the speed sensor signal after cleaning or replacement (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection/ Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 9
OK


2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the signal check in the Test Mode Procedure (Click here).

    OK:
    All test mode DTCs are cleared.



NG
Go to step 5
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
Go to step 12
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

5.CHECK FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.



    C144929E57
  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.
    Torque:
    8.3 N*m (85 kgf*cm, 73 in.*lbf)

    Text in Illustration 
    *1
    Front Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG



NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


6.INSPECT FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.INSPECT FRONT SPEED SENSOR ROTOR
  1. Remove the front axle with ABS rotor bearing assembly (for 2WD Click here, for 4WD and Pre-Runner Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    HINT:
    The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
    If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.



NG
CLEAN OR REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY
OK


8.INSPECT SKID CONTROL SENSOR WIRE
  1. Remove the skid control sensor wire.



    C214500E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    RH 
    Tester Connection
    Condition
    Specified Condition
    S4-1 - Va1-1 (FR-)
    Always
    Below 1 Ω
    S4-2 - Va1-2 (FR+)
    Always
    Below 1 Ω
    S4-1 - S4-2
    Always
    10 kΩ or higher
    LH 
    Tester Connection
    Condition
    Specified Condition
    S3-1 - Wa1-1 (FL-)
    Always
    Below 1 Ω
    S3-2 - Wa1-2 (FL+)
    Always
    Below 1 Ω
    S3-1 - S3-2
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Skid Control Sensor Wire
    *a
    RH
    *b
    LH



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Install the skid control sensor wire.

  1. Disconnect the S1 skid control ECU (brake actuator assembly) connector.

  1. Disconnect the Va1 and/or Wa1 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    RH 
    Tester Connection
    Condition
    Specified Condition
    S1-7 (FR+) - Va1-2 (FR+)
    Always
    Below 1 Ω
    S1-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    S1-6 (FR-) - Va1-1 (FR-)
    Always
    Below 1 Ω
    S1-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    LH 
    Tester Connection
    Condition
    Specified Condition
    S1-19 (FL+) - Wa1-2 (FL+)
    Always
    Below 1 Ω
    S1-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    S1-18 (FL-) - Wa1-1 (FL-)
    Always
    Below 1 Ω
    S1-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT SKID CONTROL ECU (FR+, FL+ TERMINAL)
  1. Disconnect the Va1 and/or Wa1 front speed sensor connector.

  1. Connect the S1 skid control ECU (brake actuator assembly) connector.



    C207217E21
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    RH 
    Tester Connection
    Switch Condition
    Specified Condition
    Va1-2 (FR+) - Body ground
    Ignition switch ON
    11 to 14 V
    LH 
    Tester Connection
    Switch Condition
    Specified Condition
    Wa1-2 (FL+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)
    *b
    RH
    *c
    LH



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


11.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    B



B
Go to step 12
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

12.REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).


NEXT


13.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTCs C1413 and C1414 are not output
    A
    DTCs C1413 and/or C1414 are output
    (for 2WD)
    B
    DTCs C1413 and/or C1414 are output
    (for 4WD and Pre-Runner)
    C



B
REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY (Click here)

C
REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY (Click here)
A

END