Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2194/94    Engine Speed Signal Error (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The tire pressure warning ECU receives an engine speed signal from the ECM. This DTC is stored upon entering test mode, and cleared when an engine speed signal of 1000 rpm is detected for 3 seconds or more. This DTC is output only in test mode.

DTC Code
DTC Detection Condition
Trouble Area
C2194/94
Test mode procedure is performed
  1. ECM
  2. Harness or connector
  3. Tire pressure warning ECU

WIRING DIAGRAM


C181409E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Turn the ignition switch OFF.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List /

  1. Check that the values indicated on the Techstream and on the combination meter are the same.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed/
    min.: 0 rpm
    max.: 65535 rpm
    Actual engine speed
    Engine speed indicated on the combination meter

    OK:
    Engine speed indicated on the Techstream and on the combination meter are the same.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT TIRE PRESSURE WARNING ECU (TACH SIGNAL)


    C162301E21
  1. Disconnect the T14 ECU connector.

  1. Start the engine.

  1. Check the waveform of the ECU connector using an oscilloscope while idling the engine.
    Measurement Condition 
    Item
    Contents
    Tool Setting
    5 V/DIV., 10 ms/DIV.

    OK:
    Tester Connection
    Condition
    Specified Condition
    T14-4 (TACH) - T14-9 (GND)
    Idling
    Correct waveform is as shown

    HINT:
    The wavelength becomes shorter as the engine speed increases.



NG
Go to step 3
OK

REPLACE TIRE PRESSURE WARNING ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - ECM)


    C181410E01
  1. Disconnect the T14 ECU connector.

  1. Disconnect the E14 (1GR-FE) or E7 (2TR-FE) ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (1GR-FE):
    Tester Connection
    Condition
    Specified Condition
    T14-4 (TACH) - E14-29 (TACH)
    Always
    Below 1 Ω
    T14-4 (TACH) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (2TR-FE):
    Tester Connection
    Condition
    Specified Condition
    T14-4 (TACH) - E7-1 (TACH)
    Always
    Below 1 Ω
    T14-4 (TACH) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (1GR-FE)
    B
    OK (2TR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR