Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0141    Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

for Preparation Click here


DESCRIPTION

Refer to DTC P0136 .

HINT:
  1. Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.
  2. When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.


A237486E02


DTC No.
DTC Detection Condition
Trouble Area
P0037
Heated oxygen sensor heater current less than 0.3 A
(1 trip detection logic)
  1. Open in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. ECM
P0038
Heated oxygen sensor heater current more than 2 A
(1 trip detection logic)
  1. Short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. ECM
P0141
Cumulative heater resistance correction value exceeds threshold
(2 trip detection logic)
  1. Open or short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. ECM

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentration surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
Heated Oxygen Sensor Heater Range Check (P0037 and P0038):
  1. The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM will determine that there is an open circuit in the heater. If the current is above the threshold value, the ECM will determine that there is a short circuit in the heater.
    1. Example:
      1. The ECM stores DTC P0038 when the current in the heated oxygen sensor heater is more than 2 A. Conversely, when the heater current is less than 0.3 A, DTC P0037 is stored.
Heated oxygen sensor heater performance (P0141):
  1. After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater.
    If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.

MONITOR STRATEGY


Related DTCs
P0037: Heated Oxygen Sensor Heater Range Check (Low Current)
P0038: Heated Oxygen Sensor Heater Range Check (High Current)
P0141: Heated Oxygen Sensor Heater Performance
Required Sensors/Components (Main)
Heated oxygen sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous: P0037 and P0038
Once per driving cycle: P0141
Duration
1 second: P0037 and P0038
10 seconds: P0141
MIL Operation
Immediate: P0037 and P0038
2 driving cycles: P0141
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
None

P0037: 
Battery voltage
10.5 to 20 V

P0038 (Case 1): 
Battery voltage
10.5 V or more
Engine
Running
Starter
OFF

P0038 (Case 2): 
Battery voltage
10.5 to 20 V

P0141: 
One of the following conditions is met:
Condition A or B
A. All of the following conditions are met:
Condition 1, 2, 3, 4 and 5
1. Battery voltage
10.5 V or more
2. Fuel cut
OFF
3. Time after fuel cut ON to OFF
30 seconds or more
4. Accumulated heater ON time
100 seconds or more
5. Learned heater OFF current operation
Completed
B. Duration that rear heated oxygen sensor impedance is less than 15 kΩ
2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0037: 
Heater current - Learned heater OFF current
Less than 0.3 A

P0038: 
One of the following conditions is met:
Condition A or B
A. Learned heater OFF current
More than 2 A
B. Heater current - Learned heater OFF current
2 A or more

P0141 (Heater performance monitor check): 
Accumulated heater resistance
Varies with sensor element temperature (Example: More than 23 Ω)

COMPONENT OPERATING RANGE


Heated oxygen sensor heater current
0.4 to 1 A (when engine idles, heated oxygen sensor warmed up and battery voltage 11 to 14 V)

MONITOR RESULT

Refer to Checking Monitor Status (Click here)

CONFIRMATION DRIVING PATTERN


A198819E23

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0037, P0038 or P0141.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0031 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. When the values for the Data List items O2 Heater Curr Val B1S2 is not 0 A, the heater is on.
  3. Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2 (Click here).
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)


    A237492E01
  1. Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H3-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    H3-1 (HT1B) - E4-2 (HT1B)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    H3-1 (HT1B) or E4-2 (HT1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P0141)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

Result 
Result
Proceed to
DTC is not output
A
DTC P0037, P0038 or P0141 is output
B


B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI RELAY)
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the EFI relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    H3-2 (+B) - 3 (EFI relay holder)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    H3-2 (+B) or 3 (EFI relay holder) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)