Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.
The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), current flows into the heater to heat the sensor, in order to facilitate accurate air fuel ratio detection. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A107164E51


A171616E06


DTC No.
DTC Detection Condition
Trouble Area
P2195
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
  1. (a) Air fuel ratio sensor voltage more than 3.8 V
  2. (b) Heated oxygen sensor voltage rises from below 0.21 V.
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. Air fuel ratio sensor heater
  4. A/F HEATER relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Fuel injector assembly
  9. ECM
P2195
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current 3.6 mA or more for 3 seconds.
(2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM
P2196
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
  1. (a) Air fuel ratio sensor voltage less than 2.8 V for 10 seconds
  2. (b) Heated oxygen sensor voltage falls from 0.59 V.
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. Air fuel ratio sensor heater
  4. A/F HEATER relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Fuel injector assembly
  9. ECM
P2196
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current less than 1.0 mA for 3 seconds.
(2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM

HINT:
  1. When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1.
  2. Short-term fuel trim values can also be read using the Techstream.
  3. The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the Techstream.
  4. If the air fuel ratio sensor is malfunctioning, the ECM stores the DTC P2195 or P2196.


MONITOR DESCRIPTION


Sensor voltage detection monitor
Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is below 2.8 V (very rich condition) for 5 seconds despite the rear heated oxygen sensor output voltage being below 0.59 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the rear heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.

Sensor current detection monitor
A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.
If the air fuel ratio sensor output is 3.6 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is below 1.0 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).

A107165E01


MONITOR STRATEGY


Related DTCs
P2195: Air Fuel Ratio Sensor Signal Stuck Lean
P2196: Air Fuel Ratio Sensor Signal Stuck Rich
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Heated oxygen sensor
Frequency of Operation
Continuous
Duration
5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
P0016 (VVT System - Misalignment)
P0031, P0032 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop)
P0128 (Thermostat)
P0171, P0172 (Fuel System)
P0301 - P0304 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (Idle Speed Control)
P2440, P2441, P2444, P2445 (Secondary Air Injection System)

Sensor voltage detection monitor 
Time after engine start
30 seconds or more
Air fuel ratio sensor status
Activated
Fuel system status
Closed-loop

Sensor current detection monitor 
Battery voltage
11 V or more
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Air fuel ratio sensor status
Activated
Engine coolant temperature
70°C (158°F) or more
Continuous time of fuel cut
3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS


Sensor voltage detection monitor (Lean side malfunction P2195): 
Heated oxygen sensor voltage
0.21 or more
Air fuel ratio sensor voltage
More than 3.8 V

Sensor voltage detection monitor (Rich side malfunction P2196): 
Heated oxygen sensor voltage
Below 0.59 V
Air fuel ratio sensor voltage
Less than 2.8 V

Sensor current detection monitor (High side malfunction P2195): 
Air fuel ratio sensor current
3.6 mA or more

Sensor current detection monitor (Rich side malfunction P2196): 
Air fuel ratio sensor current
Less than 1 mA

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM

Refer to DTC P0031 .

CONFIRMATION DRIVING PATTERN


A199318E34


A232909E05

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [A].
  8. On the Techstream, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  9. Drive the vehicle at a speed between 60 and 120 km/h (38 and 75 mph) for at least 10 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Shift the transmission to 2nd gear [C].
  11. Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).

  13. Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
  14. Repeat steps [C] through [E] above at least 3 times in one driving cycle.
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  16. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P2195 or P2196.
  19. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.

  20. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  5. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2195 or P2196 is output
    A
    DTC P2195 or P2196 and P0136, P0137 or P0138 are output
    DTC P2195 or P2196 and other DTCs are output
    B

    HINT:
    If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
Go to step 4
YES


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195 or P2196.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2195 or P2196 is output)
    A
    NORMAL (DTC is not output)
    B



B
Go to step 4
A

DTC CAUSED BY RUNNING OUT OF FUEL 

4.READ VALUE USING TECHSTREAM (TEST VALUE OF AIR FUEL RATIO SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / current.

  1. Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RANGE B1S1.

  1. Check the test value of the air fuel ratio sensor output current during fuel-cut.
    Result 
    Result
    Proceed to
    Within normal range (1.0 mA or higher, and below 3.6 mA)
    A
    Outside normal range (Below 1.0 mA, or 3.6 mA or higher)
    B



B
Go to step 14
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    +12%
    Rich
    Below 3.1 V
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (Heated oxygen)
    +12%
    Rich
    Higher than 0.55 V
    -12%
    Lean
    Below 0.4 V


    Result 
    Status of AFS Voltage B1S1
    Status of O2S B1S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Proceed to
    Lean
    Lean
    Actual air fuel ratio lean
    A
    Rich
    Rich
    Actual air fuel ratio rich
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    Lean/Rich
    Lean/Rich
    Normal
    Lean: During Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
    Rich: During Control the Injection Volume Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
    Lean/Rich: During Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here).



B
Go to step 14
A


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks .

    OK:
    No leaks in the intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.CHECK FOR EXHAUST GAS LEAK
  1. Check the exhaust gas leaks.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


8.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 16
OK


9.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


10.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195 or P2196.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2195 or P2196 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


12.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195 or P2196.

  1. Check the DTC judgment.

    Result 
    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END 

14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195 or P2196.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2195 or P2196 is output)
    B



B
REPLACE ECM (Click here)
A

END 

16.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)