Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1900/73    Short in Front Driver Side Pretensioner Squib Circuit

DTC    B1901/73    Open in Front Driver Side Pretensioner Squib Circuit

DTC    B1902/73    Short to GND in Front Driver Side Pretensioner Squib Circuit

DTC    B1903/73    Short to B+ in Front Driver Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The pretensioner squib (driver seat side) circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH.
This circuit signals the SRS to deploy when airbag deployment conditions are met.
These DTCs are set when a malfunction is detected in the pretensioner squib (driver seat side) circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1900/73
  1. The center airbag sensor assembly receives a line short circuit signal in the pretensioner squib (driver seat side) circuit for 2 seconds
  2. Pretensioner squib (driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 2 rear door wire (*1)
  3. Front seat outer belt assembly LH (Pretensioner squib [driver seat side])
  4. Center airbag sensor assembly
B1901/73
  1. The center airbag sensor assembly receives an open circuit signal in the pretensioner squib (driver seat side) circuit for 2 seconds
  2. Pretensioner squib (driver seat side) malfunction
  3. Center airbag sensor assembly center malfunction
  1. No. 2 floor wire
  2. No. 2 rear door wire (*1)
  3. Front seat outer belt assembly LH (Pretensioner squib [driver seat side])
  4. Center airbag sensor assembly
B1902/73
  1. The center airbag sensor assembly receives a short circuit to ground signal in the pretensioner squib (driver seat side) circuit for 0.5 seconds
  2. Pretensioner squib (driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 2 rear door wire (*1)
  3. Front seat outer belt assembly LH (Pretensioner squib [driver seat side])
  4. Center airbag sensor assembly
B1903/73
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the pretensioner squib (driver seat side) circuit for 0.5 seconds
  2. Pretensioner squib (driver seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 2 rear door wire (*1)
  3. Front seat outer belt assembly LH (Pretensioner squib [driver seat side])
  4. Center airbag sensor assembly

WIRING DIAGRAM


H101824E04


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. If using the Techstream (read the 5-digit DTCs): Using the Techstream, check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC B1900 is output.
      A
      DTC B1901 is output.
      B
      DTC B1902 is output.
      C
      DTC B1903 is output.
      D

    2. If not using the Techstream (read the 2-digit DTCs): Check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC 73 is output.
      E



B
Go to step 9

C
Go to step 14

D
Go to step 19

E
Go to step 28
A


2.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE (ACCESS CAB)
OK


3.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    Result:
    Condition
    Proceed to
    Normal (Expect access cab)
    A
    Normal ( Access cab)
    B
    Abnormal
    C



B
Go to step 6

C
CONNECT CONNECTORS
A


4.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR SHORT)


    H100883E03
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly LH.

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C109222E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900 is not output.

HINT:
DTCs other than B1900 may be output at this time, but they are not related to this check.



OK
Go to step 25
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR SHORT)


    H101878E01
  1. Disconnect the No. 2 floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 2 rear door wire connector from the front seat outer belt assembly LH.

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



OK
Go to step 8
NG


7.CHECK NO. 2 REAR DOOR WIRE (FOR SHORT)


    H101879E01
  1. Disconnect the No. 2 floor wire connector from the No. 2 rear door wire.

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101880E01
  1. Connect the No. 2 floor wire connectors to the center airbag sensor assembly and No. 2 rear door wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900 is not output.

HINT:
DTCs other than B1900 may be output at this time, but they are not related to this check.



OK
Go to step 27
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

9.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE (ACCESS CAB)
OK


10.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    Result:
    Condition
    Proceed to
    Normal (Expect access cab)
    A
    Normal ( Access cab)
    B
    Abnormal
    C



B
Go to step 12

C
CONNECT CONNECTORS
A


11.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR OPEN)


    H100883E03
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    Below 1 Ω



OK
Go to step 24
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

12.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR OPEN)


    H101878E01
  1. Disconnect the No. 2 floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 2 rear door wire connector from the front seat outer belt assembly LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    Below 1 Ω



OK
Go to step 26
NG


13.CHECK NO. 2 REAR DOOR WIRE (FOR OPEN)


    H101879E01
  1. Disconnect the No. 2 floor wire connector from the No. 2 rear door wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

14.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE (ACCESS CAB)
OK


15.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    Result:
    Condition
    Proceed to
    Normal (Expect access cab)
    A
    Normal ( Access cab)
    B
    Abnormal
    C



B
Go to step 17

C
CONNECT CONNECTORS
A


16.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO GROUND)


    H100883E03
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher



OK
Go to step 24
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

17.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO GROUND)


    H101878E01
  1. Disconnect the No. 2 floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 2 rear door wire connector from the front seat outer belt assembly LH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher



OK
Go to step 26
NG


18.CHECK NO. 2 REAR DOOR WIRE (TO GROUND)


    H101879E01
  1. Disconnect the No. 2 floor wire connector from the No. 2 rear door wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

19.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE (ACCESS CAB)
OK


20.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    Result:
    Condition
    Proceed to
    Normal (Expect access cab)
    A
    Normal ( Access cab)
    B
    Abnormal
    C



B
Go to step 22

C
CONNECT CONNECTORS
A


21.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO B+)


    H100883E03
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 24
NG

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

22.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO B+)


    H101878E01
  1. Disconnect the No. 2 floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 2 rear door wire connector from the front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the resistance.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 26
NG


23.CHECK NO. 2 REAR DOOR WIRE (TO B+)


    H101879E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No. 2 floor wire connector from the No. 2 rear door wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the resistance.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE 

24.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 21, begin from (a). If continuing from any other step, begin from (c).



    H101881E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect F17-1 (PD+) and F17-2 (PD-) of connector C.

NOTICE:
  1. Twist the end of the service wire in order to insert it into the connector.
  2. Do not forcibly insert the twisted service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1901, B1902 and B1903 are not output.

HINT:
DTCs other than B1901, B1902 or B1903 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


25.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
C109223E03

HINT:
If continuing from step 24, begin from (c). If continuing from any other step, being from (a).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 and B1903 are not output.

HINT:
DTCs other than B1900, B1901, B1902 or B1903 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH
OK

USE SIMULATION METHOD TO CHECK 

26.REPLACE CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 22, begin from (a). If continuing from any other step, begin from (c).



    H101882E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect F17-1 (PD+) and F17-2 (PD-) of connector C.

NOTICE:
  1. Twist the end of the service wire in order to insert it into the connector.
  2. Do not forcibly insert the twisted service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1901, B1902 and B1903 are not output.

HINT:
DTCs other than B1901, B1902 or B1903 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


27.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
If continuing from step 26, begin from (c). If continuing from any other step, being from (a).



    H101883E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 and B1903 are not output.

HINT:
DTCs other than B1900, B1901, B1902 or B1903 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH
OK

USE SIMULATION METHOD TO CHECK 

28.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE (ACCESS CAB)
OK


29.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.

    Result:
    Condition
    Proceed to
    Normal (Expect access cab)
    A
    Normal ( Access cab)
    B
    Abnormal
    C



B
Go to step 32

C
CONNECT CONNECTORS
A


30.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT


    H100883E03
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    Below 1 Ω
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 FLOOR WIRE
OK


31.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (PRETENSIONER SQUIB (DRIVER SEAT SIDE))


    H100884E01
  1. Replace the front seat outer belt assembly LH (Click here, Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 73 is not output.

HINT:
DTCs other than 73 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

32.CHECK DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT


    H101878E01
  1. Disconnect the No. 2 floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 2 rear door wire connector from the front seat outer belt assembly LH.

  1. Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    Below 1 Ω
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



OK
Go to step 34
NG


33.REPAIR OR REPLACE NO. 2 REAR DOOR WIRE


    H101879E01
  1. Disconnect the No. 2 floor wire connector from the No. 2 rear door wire.

  1. Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F17-2 (PD-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    Below 1 Ω
    F17-1 (PD+) - Body ground
    Always
    1 MΩ or higher
    F17-2 (PD-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-1 (PD+) - F17-2 (PD-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 REAR DOOR WIRE
OK


34.REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH


    H101884E01
  1. Replace the front seat outer belt assembly LH (Click here, Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center. Airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 73 is not output.

HINT:
DTCs other than 73 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END