Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1905/74    Short in Front Passenger Side Pretensioner Squib Circuit

DTC    B1906/74    Open in Front Passenger Side Pretensioner Squib Circuit

DTC    B1907/74    Short to GND in Front Passenger Side Pretensioner Squib Circuit

DTC    B1908/74    Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The pretensioner squib (front passenger seat side) circuit consists of the center airbag sensor assembly and the front seat outer belt assembly RH.
This circuit signals the SRS to deploy when airbag deployment conditions are met.
These DTCs are set when a malfunction is detected in the pretensioner squib (front passenger seat side) circuit.

DTC No.
DTC Detections Conditions
Trouble Areas
B1905/74
  1. The center airbag sensor assembly receives a line short circuit signal in the pretensioner squib (front passenger seat side) circuit for 2 seconds
  2. Pretensioner squib (front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. No. 1 rear door wire (*1)
  3. Front seat outer belt assembly RH (Pretensioner squib [front passenger seat side])
  4. Center airbag sensor assembly
B1906/74
  1. The center airbag sensor assembly receives an open circuit signal in the pretensioner squib (front passenger seat side) circuit for 2 seconds
  2. Pretensioner squib (front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. No. 1 rear door wire (*1)
  3. Front seat outer belt assembly RH (Pretensioner squib [front passenger seat side])
  4. Center airbag sensor assembly
B1907/74
  1. The center airbag sensor assembly receives a short circuit to ground signal in the pretensioner squib (front passenger seat side) circuit for 0.5 seconds
  2. Pretensioner squib (front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. No. 1 rear door wire (*1)
  3. Front seat outer belt assembly RH (Pretensioner squib [front passenger seat side])
  4. Center airbag sensor assembly
B1908/74
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the pretensioner squib (front passenger seat side) circuit for 0.5 seconds
  2. Pretensioner squib (front passenger seat side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. No. 1 rear door wire (*1)
  3. Front seat outer belt assembly RH (Pretensioner squib [front passenger seat side])
  4. Center airbag sensor assembly

WIRING DIAGRAM


H101824E05


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC
  1. Proceed to the appropriate step according to DTC readings.

    1. If using the Techstream (read the 5-digit DTCs): Using the Techstream, check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC B1905 is output.
      A
      DTC B1906 is output.
      B
      DTC B1907 is output.
      C
      DTC B1908 is output.
      D

    2. If not using the Techstream (read the 2-digit DTCs): Check for DTCs (Click here).

      Result:
      Result
      Proceed to
      DTC 74 is output.
      E



B
Go to step 9

C
Go to step 14

D
Go to step 19

E
Go to step 28
A


2.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE (ACCESS CAB)
OK


3.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    Result:
    Condition
    Proceed to
    Normal (Except access cab)
    A
    Normal (Access cab)
    B
    Abnormal
    C



B
Go to step 6

C
CONNECT CONNECTORS
A


4.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR SHORT)


    H101892E01
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly RH.

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101872E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905 is not output.

HINT:
DTCs other than B1905 may be output at this time, but they are not related to this check.



OK
Go to step 25
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR SHORT)


    H101885E01
  1. Disconnect the floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 1 rear door wire connector from the front seat outer belt assembly RH.

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



OK
Go to step 8
NG


7.CHECK NO. 1 REAR DOOR WIRE (FOR SHORT)


    H101886E01
  1. Disconnect the floor wire connector from the No. 1 rear door wire.

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101887E01
  1. Connect the floor wire connectors to the center airbag sensor assembly and No. 1 rear door wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905 is not output.

HINT:
DTCs other than B1905 may be output at this time, but they are not related to this check.



OK
Go to step 27
NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

9.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE (ACCESS CAB)
OK


10.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.



B
Go to step 12

C
CONNECT CONNECTORS
A


11.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR OPEN)


    H101892E01
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly RH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    Below 1 Ω



OK
Go to step 24
NG

REPAIR OR REPLACE FLOOR WIRE 

12.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (FOR OPEN)


    H101885E01
  1. Disconnect the floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 1 rear door wire connector from the front seat outer belt assembly RH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    Below 1 Ω



OK
Go to step 26
NG


13.CHECK NO. 1 REAR DOOR WIRE (FOR OPEN)


    H101886E01
  1. Disconnect the floor wire connector from the No. 1 rear door wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

14.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE (ACCESS CAB)
OK


15.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the enter airbag sensor assembly and the front airbag sensor RH.

    Result:
    Condition
    Proceed to
    Normal (Except access cab)
    A
    Normal (Access cab)
    B
    Abnormal
    C



B
Go to step 17

C
CONNECT CONNECTORS
A


16.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO GROUND)


    H101892E01
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly RH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher



OK
Go to step 24
NG

REPAIR OR REPLACE FLOOR WIRE 

17.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO GROUND)


    H101885E01
  1. Disconnect the floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 1 rear door wire connector from the front seat outer belt assembly RH.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher



OK
Go to step 26
NG


18.CHECK NO. 1 REAR DOOR WIRE (TO GROUND)


    H101886E01
  1. Disconnect the floor wire connector from the No. 1 rear door wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

19.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE (ACCESS CAB)
OK


20.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    Result:
    Condition
    Proceed to
    Normal (Except access cab)
    A
    Normal (Access cab)
    B
    Abnormal
    C



B
Go to step 22

C
CONNECT CONNECTORS
A


21.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO B+)


    H101892E01
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 24
NG

REPAIR OR REPLACE FLOOR WIRE 

22.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT (TO B+)


    H101885E01
  1. Disconnect the floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 1 rear door wire connector from the front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V



OK
Go to step 26
NG


23.CHECK NO. 1 REAR DOOR WIRE (TO B+)


    H101886E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connector from the No. 1 rear door wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the resistance.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

24.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 21, begin from (a). If continuing from any other step, begin from (c).



    H101888E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect F18-1 (PP+) and F18-2 (PP-) of connector C.

NOTICE:
  1. Twist the end of the service wire in order to insert it into the connector.
  2. Do not forcibly insert the twisted service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1906, B1907 and B1908 are not output.

HINT:
DTCs other than B1906, B1907 or B1908 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


25.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
If continuing from step 24, begin from (c). If continuing from any other step, being from (a).



    H101893E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907 and B1908 are not output.

HINT:
DTCs other than B1905, B1906, B1907 or B1908 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH
OK

OTHERS USE SIMULATION METHOD TO CHECK 

26.CHECK CENTER AIRBAG SENSOR ASSEMBLY

HINT:
If continuing from step 22, begin from (a). If continuing from any other step, begin from (c).



    H101889E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Using a service wire, connect F18-1 (PP+) and F18-2 (PP-) of connector E.

NOTICE:
  1. Twist the end of the service wire in order to insert it into the connector.
  2. Do not forcibly insert the twisted service wire into the terminals of the connector when connecting.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1906, B1907 and B1908 are not output.

HINT:
DTCs other than B1906, B1907 or B1908 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


27.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
If continuing from step 26, begin from (c). If continuing from any other step, being from (a).



    H101890E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the service wire from connector C.

  1. Connect the connector to the front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 and B1903 are not output.

HINT:
DTCs other than B1900, B1901, B1902 or B1903 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH
OK

OTHERS USE SIMULATION METHOD TO CHECK 

28.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector (on the front seat outer belt assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE (EXCEPT ACCESS CAB)

NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE (ACCESS CAB)
OK


29.CHECK CONNECTION OF CONNECTORS
  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    Result:
    Condition
    Proceed to
    Normal (Except access cab)
    A
    Normal (Access cab)
    B
    Abnormal
    C



B
Go to step 32

C
CONNECT CONNECTORS
A


30.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT


    H101892E01
  1. Disconnect the floor wire connectors from the center airbag sensor assembly and front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    Below 1 Ω
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


31.REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PASSENGER SEAT SIDE PRETENSIONER SQUIB)


    H100886E01
  1. Replace the front seat outer belt assembly RH (Click here, Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 74 is not output.

HINT:
DTCs other than 74 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

32.CHECK FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT


    H101885E01
  1. Disconnect the floor wire connector from the center airbag sensor assembly.

  1. Disconnect the No. 1 rear door wire connector from the front seat outer belt assembly RH.

  1. Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    Below 1 Ω
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



OK
Go to step 34
NG


33.CHECK NO. 1 REAR DOOR WIRE


    H101886E01
  1. Disconnect the floor wire connector from the No. 1 rear door wire.

  1. Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - Body ground
    Ignition switch ON
    Below 1 V
    F18-2 (PP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    Below 1 Ω
    F18-1 (PP+) - Body ground
    Always
    1 MΩ or higher
    F18-2 (PP-) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F18-1 (PP+) - F18-2 (PP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 REAR DOOR WIRE
OK


34.REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH


    H101891E01
  1. Replace the front seat outer belt assembly RH (Click here, Click here or Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC 74 is not output.

HINT:
DTCs other than 74 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END