Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the Techstream "CAN Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the Techstream "CAN Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Center airbag sensor assembly
  3. Yaw rate and deceleration sensor
  4. Master cylinder solenoid (skid control ECU)*1
  5. Brake actuator assembly (skid control ECU)*2
  6. Steering angle sensor
  1. *1: for Hydraulic Booster Type
  2. *2: for Vacuum Booster Type

WIRING DIAGRAM


E223284E01


INSPECTION PROCEDURE

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  4. Before measuring the resistance, first disconnect the cable from the negative battery terminal and confirm that the alarm function is no longer operating. Then, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
  5. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the Techstream. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  1. Do not remove the center airbag sensor assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  1. The open circuit confirmation of the center airbag sensor assembly, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.

1.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE AND DECELERATION SENSOR)
  1. Disconnect the Y1 yaw rate and deceleration sensor connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "Yaw Rate / Deceleration Sensor" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "Yaw Rate / Deceleration Sensor" not displayed on the Techstream.
    B



B
Go to step 3
A


2.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE AND DECELERATION SENSOR BRANCH WIRE)


    E223290E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Deceleration Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE AND DECELERATION SENSOR (Click here)  

3.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    for Hydraulic Booster Type
    A
    for Vacuum Booster Type
    B



B
Go to step 6
A


4.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
  1. Disconnect the S1 master cylinder solenoid (skid control ECU) connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "ABS/VSC/TRAC" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "ABS/VSC/TRAC" not displayed on the Techstream.
    B



B
Go to step 8
A


5.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) BRANCH WIRE)


    E223286E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-11 (CANH) - S1-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
  1. Disconnect the S1 brake actuator assembly (skid control ECU) connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "ABS/VSC/TRAC" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "ABS/VSC/TRAC" not displayed on the Techstream.
    B



B
Go to step 8
A


7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) BRANCH WIRE)


    E223287E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-25 (CANH) - S1-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

8.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the A21 center airbag sensor assembly connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "SRS Airbag" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "SRS Airbag" not displayed on the Techstream.
    B



B
Go to step 10
A


9.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
E186790E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-13 (CANH) - A21-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
E223274E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S9-10 (CANH) - S9-9 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)