Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > Downhill Assist Control Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:
  1. The transfer is in H4.
  2. The brake system is malfunctioning.
  3. The temperature of the hydraulic brake booster increases and downhill assist control is temporarily canceled.

WIRING DIAGRAM

Refer to Downhill Assist Control Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (Indicat. Downhill Assist Control)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.


Combination Meter 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Downhill Assist Control
DAC indicator light
OFF/ON
Perform the test with the vehicle stopped and the engine idling
  1. Check that the Downhill Assist Control Light on the combination meter assembly turns on or off in accordance with the Techstream operation.

    OK:
    The Downhill Assist Control Light turns on or off in accordance with the Techstream operation.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (HDCS TERMINAL)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.



    C214161E66
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-44 (HDCS) - Body ground
    Downhill assist control switch not pushed in
    10 kΩ or higher
    Downhill assist control switch pushed in
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))

  1. Reconnect the S1 skid control ECU (master cylinder solenoid) connector.



NG
Go to step 4
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

4.INSPECT DOWNHILL ASSIST CONTROL SWITCH
  1. Remove the downhill assist control switch (Click here).



    C237119E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 3
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Downhill Assist Control Switch)



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR