Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P106B    Evaporative Emission System Pressure Sensor - Secondary Air Injection Pressure Sensor Correlation

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P106B
The pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the air pressure sensor of air switching valve (Bank 1) (Air Pump Pressure (Absolute)*) differ by more than 6.98 kPa (52 mmHg) (2 trip detection logic)
  1. Canister pressure sensor (canister pump module)
  2. Air pressure sensor

HINT:
*: Name of Data List item


MONITOR DESCRIPTION

This DTC is stored when a deviation from air pressure sensor characteristics is detected.
The air pressure sensors* are checked 55 minutes after the ignition switch is turned off. If the pressures detected by the air pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

HINT:
  1. *: P106B checks the canister pressure sensor and the air pressure sensor of the air switching valve (Bank 1).
  2. Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.


MONITOR STRATEGY


Related DTCs
P106B: Evaporative Emission System Pressure Sensor - Secondary Air Injection System Pressure Sensor Correlation
Required sensors/Components
Canister pressure sensor (canister pump module)
Air pressure sensor
Frequency of operation
Once per drive cycle
Duration
Less than 65 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0452, P0453 (Evap Emission System Pressure Sensor)
P2431, P2432, P2433 (Secondary Air Injection System Pressure Sensor)
P2440, P2441, P2444, P2445 (Secondary Air Injection System)
Time elapsed after engine stop
50 minutes
Time after ECM started by soak-timer
60 seconds or more
Battery voltage
10.5 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
-10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Difference between EVAP pressure and secondary air injection absolute pressure
More than 6.98 kPa (52 mmHg)

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation Click here) [A].
  5. Start the engine.
  6. Idle the engine for 10 seconds [B].
  7. Turn the ignition switch off.
  8. Soak the vehicle for 55 minutes [C].
  9. Turn the ignition switch to ON.
  10. Turn the Techstream on.
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  12. Read pending DTCs [D].

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P106B.
  15. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Vapor Pressure Pump] (Click here).
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P106B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P106B is output
    A
    DTC P106B and other DTCs are output
    B

    HINT:
    If any other DTCs other than P106B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (AIR PUMP PRESSURE (ABSOLUTE) AND VAPOR PRESSURE PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump and Air Pump Pressure (Absolute).

  1. Compare the Vapor Pressure Pump and Air Pump Pressure (Absolute) data from the Data List with day's atmospheric pressure*.
    *: Standard atmospheric pressure is 101 kPa (760 mmHg) at sea level. The atmospheric pressure decreases by approximately 1 kPa (7.5 mmHg) for every 100 m of elevation increase. Atmospheric pressure is also affected by weather conditions. The Atmosphere pressure listed in the Data List cannot be used as a reference for this check.

    HINT:
    If you do not know the atmospheric pressure refer to the Vapor Pressure Pump value of other vehicles in the workshop and check the difference in pressure.


    Result 
    Result
    Proceed to
    If the Air Pump Pressure (Absolute) value differs from the atmospheric pressure by +/-3.5 kPa (26.25 mmHg) or more
    A
    If the Vapor Pressure Pump value differs from the atmospheric pressure by +/-3.5 kPa (26.25 mmHg) or more
    B



B
Go to step 4
A


3.REPLACE AIR SWITCHING VALVE ASSEMBLY
  1. Replace the air switching valve assembly (Click here).



NEXT
Go to step 5

4.REPLACE CANISTER PUMP MODULE
  1. Replace the canister pump module (Click here).


NEXT


5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Perform the confirmation drive pattern.

    HINT:
    Refer to the Confirmation Drive Pattern.


NEXT

END