Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC Code
Detection Condition
Trouble Area
B1653/35
When all conditions below are met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Seat position airbag sensor (front seat inner belt LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C159470E01


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

1.CHECK FOR DTC
C158841E03
  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653 is not output.

    HINT:
    Codes other than DTC B1653 maybe output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the seat position airbag sensor.

  1. Check that the connectors (on the center airbag sensor side and seat position airbag sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR)

C158842E02

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P7-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    P7-4 (LSP-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P7-2 (LSP+) - P7-4 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P7-2 (LSP+) - P7-4 (LSP-)
    Always
    1 MΩ or higher
    P7-2 (LSP+) - Body ground
    P7-4 (LSP-) - Body ground



NG
REPLACE FLOOR WIRE
OK


5.CHECK SEAT POSITION AIRBAG SENSOR (FRONT SEAT INNER BELT LH)
C158841E03
  1. Connect the connectors to the center airbag sensor and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653 is not output.

    HINT:
    Codes other than DTC B1653 maybe output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE SEAT POSITION AIRBAG SENSOR (FRONT SEAT INNER BELT LH)
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


7.CHECK CENTER AIRBAG SENSOR
C158841E03
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1653 is output (for Column Shift Type)
    A
    DTC B1653 is output (for Floor Shift Type)
    B
    DTC B1653 is not output
    C

    HINT:
    Codes other than DTC B1653 maybe output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

END (SEAT INNER BELT ASSEMBLY LH IS DEFECTIVE)