Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1651/33    Manual Cut off Switch Trouble

for Preparation Click here


DESCRIPTION

The manual cut off switch circuit consists of the center airbag sensor and the airbag cut-off switch cylinder.
The front passenger airbag can be optionally deactivated via this circuit by turning the manual cut-off switch to the OFF position.
If the front passenger airbag is deactivated, the passenger airbag OFF indicator comes on to inform the passengers.
DTC B1651/33 is recorded when a malfunction is detected in the manual cut-off switch circuit.

DTC Code
Detection Condition
Trouble Area
B1651/33
When all conditions below are met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the manual cut off switch circuit for 2 seconds.
  2. Manual cut off switch malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Airbag cut-off switch cylinder
  3. Center airbag sensor assembly

WIRING DIAGRAM


C137844E07


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

1.CHECK INSTRUMENT PANEL WIRE

C148930E03

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the center airbag sensor and the airbag cut off switch cylinder.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J33-1 (PMC-) - Body ground
    Ignition switch ON
    Below 1 V
    J33-2 (PMC+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J33-1 (PMC-) - J33-2 (PMC+)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J33-1 (PMC-) - J33-2 (PMC+)
    Always
    1 MΩ or higher
    J33-1 (PMC-) - Body ground
    J33-2 (PMC+) - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE
OK


2.INSPECT AIRBAG CUT-OFF SWITCH CYLINDER
C148932E02
  1. Remove the airbag cut-off switch cylinder.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (PMC-) - 2 (PMC+)
    Cut-off switch is in ON position (Front passenger side airbag is active)
    360 to 440 Ω
    Cut-off switch is in OFF position (Front passenger side airbag is not active)
    90 to 110 Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH CYLINDER (Click here)
OK


3.CHECK CENTER AIRBAG SENSOR
C146229E12
  1. Connect the connectors to the center airbag sensor and the airbag cut off switch cylinder.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1651 is output (for Column Shift Type)
    A
    DTC B1651 is output (for Floor Shift Type)
    B
    DTC B1651 is not output
    C

    HINT:
    Codes other than DTC B1651 maybe output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)