Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1662/45    Indicator Light Circuit Malfunction

for Preparation Click here


DESCRIPTION

The indicator light circuit consists of the center airbag sensor and the combination meter.
When the center airbag sensor detects a malfunction in the SRS airbag system, the SRS warning light comes on to inform the driver. It also comes on when the source voltage drops, and automatically goes off in approximately 10 seconds after the source voltage returns to normal (DTC is not stored).
The SRS warning light comes on for 6 seconds after the ignition switch is turned ON and goes off if the system is normal.
When an open circuit is detected, such as when the connector between the combination meter assembly and the center airbag sensor is disconnected, the SRS warning light remains on even when approximately 6 seconds elapsed after the ignition switch is turned ON.
DTC B1662/45 is recorded when a malfunction is detected in the indicator light circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1662/45
  1. The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the indicator light circuit for 2 seconds.
  2. Combination meter malfunction
  3. Center airbag sensor malfunction
  1. Combination meter assembly (SRS warning light)
  2. Center airbag sensor assembly
  3. Instrument panel wire

HINT:
When DTC B1662/45 and B1000/31 are output simultaneously, perform the troubleshooting for DTC B1662/45 first.


WIRING DIAGRAM


C159525E01


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2.CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK


3.CHECK CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and combination meter.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
C148471E02
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J46-21 (IG2) - J46-25 (E1)
    Ignition switch ON
    11 to 14 V
    J46-21 (IG2) - J46-26 (E2)



NG
REPLACE HARNESS AND CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
C159168E02
  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the J28 connector from the combination meter.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-20 (IG+) - J28-40 (E1)
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, SRS warning light goes off for approximately 10 seconds and remains on.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Column Shift Type)
    B
    OK (for Floor Shift Type)
    C

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned ON.



A
GO TO METER / GAUGE SYSTEM (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)