DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1660/43 | When all conditions below are met:
|
|

| 1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION |

Turn the ignition switch ON.
Check the passenger airbag ON/OFF indicator operation.
| ON/OFF Indicator Illumination | Proceed to |
| Remains ON | A |
| Remains OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the integration control and panel.
Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Connect the connector to the integration control and panel.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Check the passenger airbag ON/OFF indicator operation.
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connector to the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1660 is output (for Column Shift Type) | A |
| DTC B1660 is output (for Floor Shift Type) | B |
| DTC B1660 is not output | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL) |

Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the integration control and panel.
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J37-5 (PAON) - J37-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J37-5 (PAON) - J37-13 (P-AB) | Always | 1 MΩ or higher |
| J37-5 (PAON) - Body ground | ||
| J37-13 (P-AB) - Body ground |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J37-5 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| J37-13 (P-AB) - Body ground |
| Result | Proceed to |
| NG | A |
| OK (for Column Shift Type) | B |
| OK (for Floor Shift Type) | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 7.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.
|
| ||||
| OK | |
| 8.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the integration control and panel.
Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged.
|
| ||||
| OK | |
| 9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL) |

Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the integration control and panel.
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J37-5 (PAON) - J37-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J37-5 (PAON) - J37-13 (P-AB) | Always | 1 MΩ or higher |
| J37-5 (PAON) - Body ground | ||
| J37-13 (P-AB) - Body ground |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J37-5 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| J37-13 (P-AB) - Body ground |
|
| ||||
| OK | |
| 10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE) |
![]() |
Connect the connectors to the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J37-16 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the integration control and panel.
Disconnect the connectors from the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Check the indicator according to the value(s) in the table below.
| Connection | Switch Condition | Passenger airbag ON/OFF indicator |
| J46-23 (PAON) - Body ground | Ignition switch ON | "ON" comes on |
| J46-17 (P-AB) - Body ground | Ignition switch ON | "OFF" comes on |
| Result | Proceed to |
| NG (for Column Shift Type) | A |
| NG (for Floor Shift Type) | B |
| OK | C |
|
| ||||
|
| ||||
| C | |
| 12.CHECK CENTER AIRBAG SENSOR |
![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor.
Connect the negative (-) terminal cable to the battery and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1660 is output (for Column Shift Type) | A |
| DTC B1660 is output (for Floor Shift Type) | B |
| DTC B1660 is not output | C |
|
| ||||
|
| ||||
| C | ||
| ||