DTC B1690/15 Driver Side Door Side Airbag Sensor Malfunction |
DTC B1695/16 Passenger Side Door Side Airbag Sensor Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1690/15 | When both conditions below are met:
|
|
| B1695/16 | When both conditions below are met:
|
|


| 1.CHECK FOR DTC |
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 and B1695 are not output | A |
| DTC B1690 is output | B |
| DTC B1695 is output | C |
|
| ||||
|
| ||||
| C | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor RH and door side airbag sensor RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and side airbag sensor RH.
Check that the connectors (on the center airbag sensor side, the side airbag sensor RH side and door side airbag sensor RH side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M9-1 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| M9-2 (BCR+) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the side airbag sensor RH and door side airbag sensor RH.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M9-1 (BCR-) - M9-2 (BCR+) | Always | Below 1 Ω |
Disconnect the service wire from the connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M9-1 (BCR-) - M9-2 (BCR+) | Always | 1 MΩ or higher |
| M9-1 (BCR-) - Body ground | ||
| M9-2 (BCR+) - Body ground |
| Result | Proceed to |
| OK (for CrewMax) | A |
| NG | B |
| OK (for Regular Cab and Double Cab) | C |
|
| ||||
|
| ||||
| C | |
| 5.CHECK DOOR SIDE AIRBAG SENSOR RH |
![]() |
Interchange the door side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 is output (for Regular Cab) | A |
| DTC B1690 is output (for Double Cab) | B |
| DTC B1690 and B1695 are not output | C |
| DTC B1695 is output | D |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
| D | |
| 6.CHECK SIDE AIRBAG SENSOR RH |
![]() |
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 and B1695 are not output | A |
| DTC B1690 is output (for Regular Cab) | B |
| DTC B1690 is output (for Double Cab) | C |
| DTC B1695 is output (for Column Shift Type) | D |
| DTC B1695 is output (for Floor Shift Type) | E |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| E | ||
| ||
| 7.CHECK NO. 2 FLOOR WIRE |

Disconnect the No. 2 floor wire connector from the door wire RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| MQ1-1 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| MQ1-2 (BCR+) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MQ1-1 (BCR-) - MQ1-2 (BCR+) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MQ1-1 (BCR-) - MQ1-2 (BCR+) | Always | 1 MΩ or higher |
| MQ1-1 (BCR-) - Body ground | ||
| MQ1-2 (BCR+) - Body ground |
|
| ||||
| OK | ||
| ||
| 8.CHECK DOOR SIDE AIRBAG SENSOR RH |
![]() |
Interchange the door side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 is output | A |
| DTC B1690 and B1695 are not output | B |
| DTC B1695 is output | C |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| C | |
| 9.CHECK SIDE AIRBAG SENSOR RH |
![]() |
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 and B1695 are not output | A |
| DTC B1690 is output | B |
| DTC B1695 is output (for Column Shift Type) | C |
| DTC B1695 is output (for Floor Shift Type) | D |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
| D | ||
| ||
| 10.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor LH and door side airbag sensor LH.
|
| ||||
| OK | |
| 11.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and side airbag sensor LH.
Check that the connectors (on the center airbag sensor side, the side airbag sensor LH side and door side airbag sensor LH side) are not damaged.
|
| ||||
| OK | |
| 12.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified condition |
| N11-1 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| N11-2 (BCL+) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the side airbag sensor LH and door side airbag sensor LH.
Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N11-1 (BCL-) - N11-2 (BCL+) | Always | Below 1 Ω |
Disconnect the service wire from the connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N11-1 (BCL-) - Body ground | Always | 1 MΩ or higher |
| N11-2 (BCL+) - Body ground |
| Result | Proceed to |
| OK (for CrewMax) | A |
| NG | B |
| OK (for Regular Cab and Double Cab) | C |
|
| ||||
|
| ||||
| C | |
| 13.CHECK DOOR SIDE AIRBAG SENSOR LH |
![]() |
Interchange the door side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1695 is output (for Regular Cab) | A |
| DTC B1695 is output (for Double Cab) | B |
| DTC B1690 and B1695 are output | C |
| DTC B1690 is output | D |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
| D | |
| 14.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 and B1695 are not output | A |
| DTC B1695 is output (for Regular Cab) | B |
| DTC B1695 is output (for Double Cab) | C |
| DTC B1690 is output (for Column Shift Type) | D |
| DTC B1690 is output (for Floor Shift Type) | E |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| E | ||
| ||
| 15.CHECK FLOOR WIRE |

Disconnect the floor wire connector from the door wire LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| NP1-1 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| NP1-2 (BCL+) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCL+) and 2 (BCL-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| NP1-1 (BCL-) - NP1-2 (BCL+) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| NP1-1 (BCL-) - NP1-2 (BCL+) | Always | 1 MΩ or higher |
| NP1-1 (BCL-) - Body ground | ||
| NP1-2 (BCL+) - Body ground |
|
| ||||
| OK | ||
| ||
| 16.CHECK DOOR SIDE AIRBAG SENSOR LH |
![]() |
Interchange the door side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1695 is output | A |
| DTC B1690 and B1695 are output | B |
| DTC B1690 is output | C |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| C | |
| 17.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1690 and B1695 are not output | A |
| DTC B1695 is output | B |
| DTC B1690 is output (for Column Shift Type) | C |
| DTC B1690 is output (for Floor Shift Type) | D |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
| D | ||
| ||