Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Front Power Seat does not Operate with Front Power Seat Switch

for Preparation Click here


DESCRIPTION

When the front power seat switch is operated, a signal is sent to the front seat adjuster, which then operates each motor. When 2 or more signals are input to the front seat adjuster, the motors only operate when the signals are from the slide switch and reclining switch.

WIRING DIAGRAM


B167294E02


B167296E01


INSPECTION PROCEDURE

1.CHECK SEAT OPERATION
  1. Operate the power seat switch and check that the front power seat operates.
    Result 
    Result
    Proceed to
    Driver side power seat does not operate
    A
    Driver side lumbar does not operate
    B
    Driver side leg support does not operate
    C
    Passenger side power seat does not operate
    D
    Passenger side lumbar does not operate
    E



B
Go to step 6

C
Go to step 10

D
Go to step 14

E
Go to step 18
A


2.INSPECT FUSE (ECU-B1, ECU-IG No. 1, FR P/SEAT)
  1. Remove the ECU-B1 fuse from the engine room relay block.

  1. Remove the FR P/SEAT LH and ECU-IG No. 1 fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-B1 fuse
    Always
    Below 1 Ω
    ECU-IG No. 1 fuse
    FR P/SEAT LH fuse



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)


    B166806E01
  1. Disconnect the Z9 and Z10 switch connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z9-5 (+B) - Body ground
    Always
    11 to 14 V
    Z10-4 (IG) - Body ground
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V
    Z10-8 (SYSB) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Z9-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH


    B167282E01
  1. Disconnect the Z9 switch connector.

  1. Apply battery voltage and check the operation of the power seat.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal Z9-2 (SLD+)
    Battery negative (-) → Terminal Z9-3 (SLD-)
    Seat slides forward (A)
    Battery negative (-) → Terminal Z9-2 (SLD+)
    Battery positive (+) → Terminal Z9-3 (SLD-)
    Seat slides rearward (B)
    Battery positive (+) → Terminal Z9-7 (LFT+)
    Battery negative (-) → Terminal Z9-9 (LFT-)
    Seat cushion rises (C)
    Battery negative (-) → Terminal Z9-7 (LFT+)
    Battery positive (+) → Terminal Z9-9 (LFT-)
    Seat cushion lowers (D)
    Battery positive (+) → Terminal Z9-6 (FRV+)
    Battery negative (-) → Terminal Z9-4 (FRV-)
    Seat cushion front rises (E)
    Battery negative (-) → Terminal Z9-6 (FRV+)
    Battery positive (+) → Terminal Z9-4 (FRV-)
    Seat cushion front lowers (F)
    Battery positive (+) → Terminal Z9-8 (RCL+)
    Battery negative (-) → Terminal Z9-10 (RCL-)
    Seat tilts forward (G)
    Battery negative (-) → Terminal Z9-8 (RCL+)
    Battery positive (+) → Terminal Z9-10 (RCL-)
    Seat reclines (H)



NG
Go to step 5
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

5.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POSITION MOTOR)


    B167287E01
  1. Disconnect the Z9 switch connector.

  1. Disconnect the Z3, Z4, Z5 and Z6 motor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Z9-2 (SLD+) - Z3-1
    Always
    Below 1 Ω
    Z9-3 (SLD-) - Z3-2
    Z9-6 (FRV+) - Z4-1
    Z9-4 (FRV-) - Z4-2
    Z9-7 (LFT+) - Z5-2
    Z9-9 (LFT-) - Z5-1
    Z9-8 (RCL+) - Z6-2
    Z9-10 (RCL-) - Z6-1
    Z9-2 (SLD+) - Body ground
    Always
    10 kΩ or higher
    Z9-3 (SLD-) - Body ground
    Z9-6 (FRV+) - Body ground
    Z9-4 (FRV-) - Body ground
    Z9-7 (LFT+) - Body ground
    Z9-9 (LFT-) - Body ground
    Z9-8 (RCL+) - Body ground
    Z9-10 (RCL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (Click here)  

6.INSPECT FUSE (FR P/SEAT LH)
  1. Remove the FR P/SEAT LH fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FR P/SEAT LH fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


7.INSPECT FRONT POWER SEAT LUMBAR SWITCH


    B168171E01
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (H)
    HOLD
    Below 1 Ω
    1 (R) - 2 (E2)
    1 (R) - 2 (E2)
    OFF
    4 (H) - 5 (E)
    1 (R) - 3 (B)
    RELEASE
    4 (H) - 5 (E)



NG
REPLACE FRONT POWER SEAT LUMBAR SWITCH (Click here)
OK


8.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH


    B167404E01
  1. Disconnect the Z2 switch connector.

  1. Apply battery voltage and check the operation of the power seat.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal Z2-4 (H)
    Battery negative (-) → Terminal Z2-1 (R)
    Lumbar support moves forward (A)
    Battery negative (-) → Terminal Z2-4 (H)
    Battery positive (+) → Terminal Z2-1 (R)
    Lumbar support moves rearward (B)



NG
Go to step 9
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POWER SEAT LUMBAR SWITCH - BATTERY AND BODY GROUND) 

9.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT LUMBAR SWITCH - LUMBAR SUPPORT MOTOR LH)


    B167403E02
  1. Disconnect the Z2 switch connector.

  1. Disconnect the Z7 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Z2-1 (R) - Z7-2
    Always
    Below 1 Ω
    Z2-4 (H) - Z7-1
    Always
    Z2-1 (R) - Body ground
    Always
    10 kΩ or higher
    Z2-4 (H) - Body ground
    Always



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (Click here)  

10.INSPECT FUSE (FR P/SEAT LH)
  1. Remove the FR P/SEAT LH fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FR P/SEAT LH fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


11.INSPECT LEG SUPPORT ADJUSTMENT SWITCH


    B168172E02
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (CSNF) - 3 (B)
    OPEN
    Below 1 Ω
    4 (CSNR) - 5 (E)
    1 (CSNF) - 2 (E2)
    OFF
    4 (CSNR) - 5 (E)
    1 (CSNF) - 2 (E2)
    CLOSE
    3 (B) - 4 (CSNR)



NG
REPLACE LEG SUPPORT ADJUSTMENT SWITCH (Click here)
OK


12.INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH


    B167738E01
  1. Disconnect the U1 switch connector.

  1. Apply battery voltage and check the operation of the power seat.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal U1-4 (CSNR)
    Battery negative (-) → Terminal U1-1 (CSNF)
    Leg support opens (A)
    Battery negative (-) → Terminal U1-4 (CSNR)
    Battery positive (+) → Terminal U1-1 (CSNF)
    Leg support closes (B)



NG
Go to step 13
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (LEG SUPPORT ADJUSTMENT SWITCH - BATTERY AND BODY GROUND) 

13.CHECK HARNESS AND CONNECTOR (LEG SUPPORT ADJUSTMENT SWITCH - LEG SUPPORT MOTOR LH)


    B167403E04
  1. Disconnect the U1 switch connector.

  1. Disconnect the Z8 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    U1-1 (CSNF) - Z8-1
    Always
    Below 1 Ω
    U1-4 (CSNR) - Z8-2
    U1-1 (CSNF) - Body ground
    Always
    10 kΩ or higher
    U1-4 (CSNR) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (Click here)  

14.INSPECT FUSE (FR P/SEAT RH)
  1. Remove the FR P/SEAT RH fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FR P/SEAT RH fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


15.INSPECT FRONT POWER SEAT SWITCH RH


    B167765E01
  1. Remove the switch (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Slide switch 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (SLDF) - 1 (B)
    FRONT
    Below 1 Ω
    6 (SLDR) - 4 (E)
    9 (SLDF) - 4 (E)
    OFF
    6 (SLDR) - 4 (E)
    9 (SLDF) - 4 (E)
    REAR
    6 (SLDR) - 1 (B)
    Reclining switch 
    Tester Connection
    Switch Condition
    Specified Condition
    3 (RCLF) - 1 (B)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    3 (RCLF) - 4 (E)
    OFF
    2 (RCLR) - 4 (E)
    3 (RCLF) - 4 (E)
    REAR
    2 (RCLR) - 1 (B)



NG
REPLACE FRONT POWER SEAT SWITCH RH (Click here)
OK


16.INSPECT FRONT SEAT ADJUSTER ASSEMBLY RH


    B167290E01
  1. Disconnect the Y9 switch connector.

  1. Apply battery voltage and check the operation of the power seat.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 9 (SLDF)
    Battery negative (-) → Terminal 6 (SLDR)
    Seat slides forward (A)
    Battery negative (-) → Terminal 9 (SLDF)
    Battery positive (+) → Terminal 6 (SLDR)
    Seat slides rearward (B)
    Battery positive (+) → Terminal 3 (RCLF)
    Battery negative (-) → Terminal 2 (RCLR)
    Seat tilts forward (C)
    Battery negative (-) → Terminal 3 (RCLF)
    Battery positive (+) → Terminal 2 (RCLR)
    Seat reclines (D)



NG
Go to step 17
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POWER SEAT SWITCH RH - BATTERY AND BODY GROUND) 

17.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - POSITION MOTOR)


    B167291E02
  1. Disconnect the Y9 switch connector.

  1. Disconnect the Y12 and Y13 motor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y9-9 (SLDF) -Y12-2
    Always
    Below 1 Ω
    Y9-6 (SLDR) - Y12-1
    Y9-3 (RCLF) - Y13-2
    Y9-2 (RCLR) - Y13-1
    Y9-9 (SLDF) - Body ground
    Always
    10 kΩ or higher
    Y9-6 (SLDR) - Body ground
    Y9-3 (RCLF) - Body ground
    Y9-2 (RCLR) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (Click here)  

18.INSPECT FUSE (FR P/SEAT RH)
  1. Remove the FR P/SEAT RH fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FR P/SEAT RH fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


19.INSPECT FRONT POWER SEAT LUMBAR SWITCH


    B167704E01
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (H1)
    HOLD
    Below 1 Ω
    1 (R1) - 2 (E2)
    1 (R1) - 2 (E2)
    4 (H1) - 5 (E)
    OFF
    1 (R1) - 3 (B)
    RELEASE
    4 (H1) - 5 (E)



NG
REPLACE FRONT POWER SEAT LUMBAR SWITCH (Click here)
OK


20.INSPECT FRONT SEAT ADJUSTER ASSEMBLY RH


    B167406E01
  1. Disconnect the Y10 switch connector.

  1. Apply battery voltage and check the operation of the power seat.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal Y10-4 (H1)
    Battery negative (-) → Terminal Y10-1 (R1)
    Lumbar support moves forward (A)
    Battery negative (-) → Terminal Y10-4 (H1)
    Battery positive (+) → Terminal Y10-1 (R1)
    Lumbar support moves rearward (B)



NG
Go to step 21
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POWER SEAT LUMBAR SWITCH - BATTERY AND BODY GROUND) 

21.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT LUMBAR SWITCH - LUMBAR SUPPORT MOTOR RH)


    B167403E05
  1. Disconnect the Y10 switch connector.

  1. Disconnect the Y11 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y10-1 (R1) - Y11-1
    Always
    Below 1 Ω
    Y10-4 (H1) - Y11-2
    Y10-1 (R1) - Body ground
    Always
    10 kΩ or higher
    Y10-4 (H1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH (Click here)