Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1630/23    Driver Side Rear Airbag Sensor Circuit Malfunction

DTC    B1635/24    Front Passenger Side Rear Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor LH and RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23 or B1635/24 is recorded when a malfunction is detected in the side airbag sensor LH or RH circuit.

HINT:
"Rear Airbag Sensor" refers to the side airbag sensor.


DTC Code
Detection Condition
Trouble Area
B1630/23
When both conditions below are met:
  1. Side airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor LH
  2. Center airbag sensor assembly
B1635/24
When both conditions below are met:
  1. Side airbag sensor RH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor RH
  2. Center airbag sensor assembly

WIRING DIAGRAM


C158884E01


C158884E05


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

1.CHECK FOR DTC
  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1630 is output
    B
    DTC B1635 is output
    C



A
USE SIMULATION METHOD TO CHECK (Click here)

B
Go to step 12
C


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)

C158835E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q4-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    Q4-4 (BBR+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-3 (BBR-) - Q4-4 (BBR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-3 (BBR-) - Q4-4 (BBR+)
    Always
    1 MΩ or higher
    Q4-3 (BBR-) - Body ground
    Q4-4 (BBR+) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK SIDE AIRBAG SENSOR RH
C146230E03
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1630 is output (for Double Cab)
    B
    DTC B1630 is output (for CrewMax)
    C
    DTC B1635 is output
    D

    HINT:
    Codes other than DTC B1630 and B1635 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
REPLACE SIDE AIRBAG SENSOR RH (Click here)
D


6.CHECK CONNECTION OF CONNECTORS
  1. Check that the connector is properly connected to the door side airbag sensor RH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


7.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor RH and door side airbag sensor RH.

  1. Check that the connector (on the door side airbag sensor RH side) is not damaged.

    OK:
    The connector is not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


8.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

C158839E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M9-1 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V
    M9-2 (BCR+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M9-1 (BCR-) - M9-2 (BCR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M9-1 (BCR-) - M9-2 (BCR+)
    Always
    1 MΩ or higher
    M9-1 (BCR-) - Body ground
    M9-2 (BCR+) - Body ground



NG
Go to step 11
OK


9.CHECK FOR DTC


    C167367E01
  1. Connect the connectors to the side airbag sensor RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1635 is output.

HINT:
Codes other than B1635 maybe output at this time, but they are not related to this check.

Result 
Result
Proceed to
NG (for Double Cab)
A
NG (for CrewMax)
B
OK
C


A
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)

B
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)
C


10.CHECK SIDE AIRBAG SENSOR RH
C146230E03
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1635 is output (for Column Shift Type)
    B
    DTC B1635 is output (for Floor Shift Type)
    C
    DTC B1630 is output (for Double Cab)
    D
    DTC B1630 is output (for CrewMax)
    E

    HINT:
    Codes other than DTC B1630 and B1635 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

D
REPLACE SIDE AIRBAG SENSOR RH (Click here)
E

REPLACE SIDE AIRBAG SENSOR RH (Click here)  

11.CHECK NO. 2 FLOOR WIRE

C158885E01

  1. Disconnect the No. 2 floor wire connector from the door wire RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    MQ1-1 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V
    MQ1-2 (BCR+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    MQ1-1 (BCR-) - MQ1-2 (BCR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    MQ1-1 (BCR-) - MQ1-2 (BCR+)
    Always
    1 MΩ or higher
    MQ1-1 (BCR-) - Body ground
    MQ1-2 (BCR+) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE DOOR WIRE RH 

12.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


13.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


14.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)

C158840E04

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P4-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V
    P4-4 (BBL+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P4-3 (BBL-) - P4-4 (BBL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P4-3 (BBL-) - P4-4 (BBL+)
    Always
    1 MΩ or higher
    P4-3 (BBL-) - Body ground
    P4-4 (BBL+) - Body ground



NG
REPLACE FLOOR WIRE
OK


15.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1635 is output (for Double Cab)
    B
    DTC B1635 is output (for CrewMax)
    C
    DTC B1630 is output
    D

    HINT:
    Codes other than DTC B1630 and B1635 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)
D


16.CHECK NO. 2 FLOOR WIRE (SIDE AIRBAG SENSOR LH - DOOR SIDE AIRBAG SENSOR LH)

C158839E02

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N11-1 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V
    N11-2 (BCL+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-1 (BCL-) - N11-2 (BCL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-1 (BCL-) - N11-2 (BCL+)
    Always
    1 MΩ or higher
    N11-1 (BCL-) - Body ground
    N11-2 (BCL+) - Body ground



NG
Go to step 19
OK


17.CHECK FOR DTC


    C167367E02
  1. Connect the connectors to the side airbag sensor LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630 is output.

HINT:
Codes other than B1630 maybe output at this time, but they are not related to this check.

Result 
Result
Proceed to
NG (for Double Cab)
A
NG (for CrewMax)
B
OK
C


A
REPLACE DOOR SIDE AIRBAG SENSOR LH (Click here)

B
REPLACE DOOR SIDE AIRBAG SENSOR LH (Click here)
C


18.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1630 is output (for Column Shift Type)
    B
    DTC B1630 is output (for Floor Shift Type)
    C
    DTC B1635 is output (for Double Cab)
    D
    DTC B1635 is output (for CrewMax)
    E

    HINT:
    Codes other than DTC B1630 and B1635 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

D
REPLACE SIDE AIRBAG SENSOR LH (Click here)
E

REPLACE SIDE AIRBAG SENSOR LH (Click here)  

19.CHECK FLOOR WIRE

C158885E02

  1. Disconnect the floor wire connector from the door wire LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    NP1-1 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V
    NP1-2 (BCL+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCL+) and 2 (BCL-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    NP1-1 (BCL-) - NP1-2 (BCL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    NP1-1 (BCL-) - NP1-2 (BCL+)
    Always
    1 MΩ or higher
    NP1-1 (BCL-) - Body ground
    NP1-2 (BCL+) - Body ground



NG
REPLACE FLOOR WIRE
OK

REPLACE DOOR WIRE LH