SFI SYSTEM > Cranking Holding Function Circuit |


| 1.CHECK CRANKING |
Check the cranking of the engine.
| Test Result | Proceed to |
| Cranking possible and holding control operates | A |
| Does not crank | B |
| Cranking possible but holding control does not operate | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and when the engine is started.
| Ignition Switch Position | Display (Starter Signal) |
| ON | OFF |
| START | ON |
|
| ||||
| OK | |
| 3.INSPECT STARTER RELAY (ST) |
Inspect the starter relay (ST) (Click here).
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - STARTER RELAY (ST)) |
Disconnect the park/neutral Position switch assembly connector.
Remove the starter relay (ST) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay (1) - D35-5 | Always | Below 1 Ω |
| ST relay (1) or D35-5 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Remove the starter relay (ST) from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay (2) - ST relay (5) | Always | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | Starter Relay (ST) |
|
| ||||
| OK | |
| 6.INSPECT STARTER ASSEMBLY |
Inspect the starter assembly (for 1.6 kW type) (Click here).
Inspect the starter assembly (for 1.4 kW type) (Click here).
| Test Result | Proceed to |
| OK | A |
| NG (for 1.6 kW type) | B |
| NG (for 1.4 kW type) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 7.CHECK IGNITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the ignition switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J9-5 (AM2) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Ignition Switch Assembly) |
|
| ||||
| OK | |
| 8.INSPECT IGNITION SWITCH ASSEMBLY |
Inspect the ignition switch assembly (Click here).
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D35-4 - Body ground | Engine cranking | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch Assembly) |
|
| ||||
| OK | |
| 10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM) |
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J9-7 (ST2) - A24-14 (STSW) | Always | Below 1 Ω |
| J9-7 (ST2) or A24-14 (STSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D35-4 - D74-16 (STAR) | Always | Below 1 Ω |
| D35-4 or D74-16 (STAR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||