Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator consists of the center airbag sensor assembly, occupant classification ECU, hazard warning switch assembly, and 4 occupant classification sensors. This system controls the passenger airbag deployment according to the occupancy condition of the front passenger seat, and also displays those detected conditions.

WIRING DIAGRAM


C245494E01


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch off.

  1. Loosen the 4 installation bolts of the front seat RH.

  1. Tighten the 4 installation bolts of the front seat RH to the specified torque.

    1. for Manual Seat (Click here)
    2. for Power Seat (Click here)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }


NEXT


2.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    Zero point calibration is completed using tester.



NG
Go to step 3
OK

END 

3.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, read the "Data List" (Click here).

    Occupant Detection: 
    Tester Display
    Measure Item / Range
    Normal Condition
    Diagnostic Note
    Passenger Buckle SW
    Passenger side buckle switch / Set, Unset or NG
    Set: Passenger side seat belt is fastened
    Unset: Passenger side seat belt is unfastened
    NG: Passenger side seat belt is malfunctioning
    -

    OK:
    Display changed correctly according to operation of buckle switch.



NG
Go to step 8
OK


4.READ VALUE USING TECHSTREAM (OCCUPANT DETECTION SENSOR)
  1. Fasten the passenger side seat belt.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, read the "Data List" (Click here).

    Occupant Detection: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    FL Sensor Voltage
    Front left sensor voltage/
    Min.: 0 V
    Max.: 19.8 V
    0 to 4.7 V
    -
    FR Sensor Voltage
    Front right sensor voltage/
    Min.: 0 V
    Max.: 19.8 V
    0 to 4.7 V
    -
    RL Sensor Voltage
    Rear left sensor voltage/
    Min.: 0 V
    Max.: 19.8 V
    0 to 4.7 V
    -
    RR Sensor Voltage
    Rear right sensor voltage/
    Min.: 0 V
    Max.: 19.8 V
    0 to 4.7 V
    -
    FL Sensor Weight Info
    Front left sensor weight information/
    Min.: -17 kg (-37.48 lb)
    Max.: 27 kg (59.52 lb)
    -17 to 27 kg
    (-37.48 to 59.52 lb)
    -
    FR Sensor Weight Info
    Front right sensor weight information/
    Min.: -17 kg (-37.48 lb)
    Max.: 27 kg (59.52 lb)
    -17 to 27 kg
    (-37.48 to 59.52 lb)
    -
    RL Sensor Weight Info
    Rear left sensor weight information/
    Min.: -17 kg (-37.48 lb)
    Max.: 37 kg (81.57 lb)
    -17 to 37 kg
    (-37.48 to 81.57 lb)
    -
    RR Sensor Weight Info
    Rear right sensor weight information/
    Min.: -17 kg (-37.48 lb)
    Max.: 37 kg (81.57 lb)
    -17 to 37 kg
    (-37.48 to 81.57 lb)
    -
    Total Weight Information
    Total weight information/
    Min.: -68 kg (-149.91 lb)
    Max.: 128 kg (282.19 lb)
    -68 to 128 kg
    (-149.91 to 282.19 lb)
    -
    Result 
    Result
    Proceed to
    Display is as specified in normal condition
    A
    Display is not as specified in normal condition (for Manual Seat)
    B
    Display is not as specified in normal condition (for Power Seat)
    C



B
REPLACE OCCUPANT CLASSIFICATION ECU (Click here)

C
REPLACE OCCUPANT CLASSIFICATION ECU (Click here)
A


5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat frame with adjuster RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END 

8.CHECK CONNECTOR
  1. Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.

  1. Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged.

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


9.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt RH (Click here).

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END