Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

DTC    B1561    XM Tuner Disconnected (Command Line)

DTC    B159F    No Response from XM Tuner

for Preparation Click here


DESCRIPTION

The navigation receiver assembly and stereo component tuner assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component tuner assembly, this DTC will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B1561*
When either condition below is met:
  1. Stereo component tuner assembly is not/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the stereo component tuner assembly is not possible when the engine is started.
  1. Stereo component tuner assembly power source circuit
  2. AVC-LAN circuit between navigation receiver assembly and stereo component tuner assembly
  3. Navigation receiver assembly
  4. Stereo component tuner assembly
  5. Multi-media interface ECU
B159F
Within the time-out period, there was no response from the stereo component tuner assembly to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM


E190158E02


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.
      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

HINT:
  1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
  2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER POWER SOURCE)


    E168575E42
  1. Disconnect the K27 stereo component tuner assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K27-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K27-12 (+B) - K27-7 (GND)
    Always
    11 to 14 V
    K27-11 (ACC) - K27-7 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - MULTI-MEDIA INTERFACE ECU)


    E191655E01
  1. Disconnect the K27 stereo component tuner assembly connector.

  1. Disconnect the J108 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K27-9 (TX+) - J108-4 (TX2+)
    Always
    Below 1 Ω
    K27-10 (TX-) - J108-5 (TX2-)
    Always
    Below 1 Ω
    K27-9 (TX+) - Body ground
    Always
    10 kΩ or higher
    K27-10 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - MULTI-MEDIA INTERFACE ECU)


    E191656E01
  1. Disconnect the K8 navigation receiver assembly connector.

  1. Disconnect the J107 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K8-9 (TXM+) - J107-9 (TX1+)
    Always
    Below 1 Ω
    K8-10 (TXM-) - J107-10 (TX1-)
    Always
    Below 1 Ω
    K8-9 (TXM+) - Body ground
    Always
    10 kΩ or higher
    K8-10 (TXM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE STEREO COMPONENT TUNER ASSEMBLY
  1. Temporarily replace the stereo component tuner assembly with new or normally one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 8
OK

END (STEREO COMPONENT TUNER ASSEMBLY IS FAULTY) 

8.REPLACE MULTI-MEDIA INTERFACE ECU
  1. Temporarily replace the multi-media interface ECU with new or normally one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (MULTI-MEDIA INTERFACE ECU IS FAULTY)