AUDIO AND VISUAL SYSTEM > Speaker Circuit (Independent Amplifier) |


| 1.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Malfunction in front speaker area | A |
| Malfunction in rear speaker area | B |
|
| ||||
| A | |
| 2.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 3 speaker assembly | C |
| Front No. 4 speaker assembly | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.8 to 2.6 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER) |
![]() |
Disconnect the K17 stereo component amplifier assembly connector.
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K17-9 (WFR+) - M8-1 | Always | Below 1 Ω |
| K17-3 (WFR-) - M8-2 | Always | Below 1 Ω |
| K17-9 (WFR+) - Body ground | Always | 10 kΩ or higher |
| K17-3 (WFR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K17-2 (WFL+) - N10-1 | Always | Below 1 Ω |
| K17-1 (WFL-) - N10-2 | Always | Below 1 Ω |
| K17-2 (WFL+) - Body ground | Always | 10 kΩ or higher |
| K17-1 (WFL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWR+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWR-) | Always | Below 1 Ω |
| 3 (TWR+) - 4 (TWR-) | Always | 1.5 to 2.5 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWL+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWL-) | Always | Below 1 Ω |
| 3 (TWL+) - 4 (TWL-) | Always | 1.5 to 2.5 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the K16 stereo component amplifier assembly connector.
Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K16-2 (FR+) - K10-3 (TWR+) | Always | Below 1 Ω |
| K16-6 (FR-) - K10-4 (TWR-) | Always | Below 1 Ω |
| K16-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| K16-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K16-8 (FL+) - K12-3 (TWL+) | Always | Below 1 Ω |
| K16-7 (FL-) - K12-4 (TWL-) | Always | Below 1 Ω |
| K16-8 (FL+) - Body ground | Always | 10 kΩ or higher |
| K16-7 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
![]() |
Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 3 | Always | 3.0 to 4.2 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER) |
![]() |
Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.
Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K10-1 (+) - M1-3 | Always | Below 1 Ω |
| K10-2 (-) - M1-1 | Always | Below 1 Ω |
| K10-1 (+) - Body ground | Always | 10 kΩ or higher |
| K10-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K12-1 (+) - N1-3 | Always | Below 1 Ω |
| K12-2 (-) - N1-1 | Always | Below 1 Ω |
| K12-1 (+) - Body ground | Always | 10 kΩ or higher |
| K12-2 (-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Double Cab) | A |
| OK (for CrewMax) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY |
![]() |
Disconnect the K14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.5 to 2.1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER) |
![]() |
Disconnect the K17 stereo component amplifier assembly connector.
Disconnect the K14 front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K17-4 (CTR+) - K14-1 | Always | Below 1 Ω |
| K17-10 (CTR-) - K14-2 | Always | Below 1 Ω |
| K17-4 (CTR+) - Body ground | Always | 10 kΩ or higher |
| K17-10 (CTR-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Rear No. 2 speaker assembly | A |
| Rear No. 1 speaker assembly (for CrewMax) | B |
| Rear No. 1 speaker assembly (for Double Cab) | C |
| w/ Box No. 1 speaker assembly | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (-TW) - 3 (+TW) | Always | 3.0 to 4.2 Ω |
| 1 (-TW) - 2 (-) | Always | Below 1 Ω |
| 3 (+TW) - 4 (+) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER) |
![]() |
Disconnect the K16 stereo component amplifier assembly connector.
Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K16-10 (RR+) - O2-3 (+TW) | Always | Below 1 Ω |
| K16-4 (RR-) - O2-1 (-TW) | Always | Below 1 Ω |
| K16-10 (RR+) - Body ground | Always | 10 kΩ or higher |
| K16-4 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K16-3 (RL+) - O8-3 (+TW) | Always | Below 1 Ω |
| K16-9 (RL-) - O8-1 (-TW) | Always | Below 1 Ω |
| K16-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| K16-9 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.8 to 2.6 Ω |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER - REAR NO. 1 SPEAKER) |
![]() |
Disconnect the O2*1 and/or O8*2 rear No. 2 speaker connector.
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O2-4 (+) - O1-1 | Always | Below 1 Ω |
| O2-2 (-) - O1-2 | Always | Below 1 Ω |
| O2-4 (+) - Body ground | Always | 10 kΩ or higher |
| O2-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| O8-4 (+) - O7-1 | Always | Below 1 Ω |
| O8-2 (-) - O7-2 | Always | Below 1 Ω |
| O8-4 (+) - Body ground | Always | 10 kΩ or higher |
| O8-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 16.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.8 to 2.6 Ω |
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 1 SPEAKER) |
![]() |
Disconnect the K16 stereo component amplifier assembly connector.
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K16-10 (RR+) - O1-1 | Always | Below 1 Ω |
| K16-4 (RR-) - O1-2 | Always | Below 1 Ω |
| K16-10 (RR+) - Body ground | Always | 10 kΩ or higher |
| K16-4 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K16-3 (RL+) - O7-1 | Always | Below 1 Ω |
| K16-9 (RL-) - O7-2 | Always | Below 1 Ω |
| K16-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| K16-9 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 18.INSPECT W/ BOX NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the P14 w/ box No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1.6 to 2.4 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
|
| ||||
|
| ||||
| A | |
| 19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - W/ BOX NO. 1 SPEAKER) |
![]() |
Disconnect the K17 stereo component amplifier assembly connector.
Disconnect the P14 w/ box No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K17-5 (WF1+) - P14-1 | Always | Below 1 Ω |
| K17-12 (WF1-) - P14-2 | Always | Below 1 Ω |
| K17-5 (WF1+) Body ground | Always | Below 1 Ω |
| K17-12 (WF1-) Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||