Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly sends sound signals to the speaker.

WIRING DIAGRAM


E146449E02


E160611E03


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 11
A


2.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 1 speaker assembly
    A
    Front No. 2 speaker assembly
    B
    Front No. 3 speaker assembly
    C
    Front No. 4 speaker assembly
    D



B
Go to step 5

C
Go to step 7

D
Go to step 9
A


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER)


    E191172E01
  1. Disconnect the K17 stereo component amplifier assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K17-9 (WFR+) - M8-1
    Always
    Below 1 Ω
    K17-3 (WFR-) - M8-2
    Always
    Below 1 Ω
    K17-9 (WFR+) - Body ground
    Always
    10 kΩ or higher
    K17-3 (WFR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K17-2 (WFL+) - N10-1
    Always
    Below 1 Ω
    K17-1 (WFL-) - N10-2
    Always
    Below 1 Ω
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E144969E34
  1. Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    Always
    Below 1 Ω
    3 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    Always
    Below 1 Ω
    3 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER)


    E191173E01
  1. Disconnect the K16 stereo component amplifier assembly connector.

  1. Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-2 (FR+) - K10-3 (TWR+)
    Always
    Below 1 Ω
    K16-6 (FR-) - K10-4 (TWR-)
    Always
    Below 1 Ω
    K16-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    K16-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-8 (FL+) - K12-3 (TWL+)
    Always
    Below 1 Ω
    K16-7 (FL-) - K12-4 (TWL-)
    Always
    Below 1 Ω
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E160614
  1. Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
A


8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E146500E04
  1. Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.

  1. Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K10-1 (+) - M1-3
    Always
    Below 1 Ω
    K10-2 (-) - M1-1
    Always
    Below 1 Ω
    K10-1 (+) - Body ground
    Always
    10 kΩ or higher
    K10-2 (-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K12-1 (+) - N1-3
    Always
    Below 1 Ω
    K12-2 (-) - N1-1
    Always
    Below 1 Ω
    K12-1 (+) - Body ground
    Always
    10 kΩ or higher
    K12-2 (-) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Double Cab)
    A
    OK (for CrewMax)
    B
    NG
    C



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

9.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    E146506
  1. Disconnect the K14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER)


    E191176E01
  1. Disconnect the K17 stereo component amplifier assembly connector.

  1. Disconnect the K14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-4 (CTR+) - K14-1
    Always
    Below 1 Ω
    K17-10 (CTR-) - K14-2
    Always
    Below 1 Ω
    K17-4 (CTR+) - Body ground
    Always
    10 kΩ or higher
    K17-10 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

11.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Rear No. 2 speaker assembly
    A
    Rear No. 1 speaker assembly (for CrewMax)
    B
    Rear No. 1 speaker assembly (for Double Cab)
    C
    w/ Box No. 1 speaker assembly
    D



B
Go to step 14

C
Go to step 16

D
Go to step 18
A


12.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E160614E22
  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)
    Always
    Below 1 Ω



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER)


    E191175E01
  1. Disconnect the K16 stereo component amplifier assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-10 (RR+) - O2-3 (+TW)
    Always
    Below 1 Ω
    K16-4 (RR-) - O2-1 (-TW)
    Always
    Below 1 Ω
    K16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    K16-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-3 (RL+) - O8-3 (+TW)
    Always
    Below 1 Ω
    K16-9 (RL-) - O8-1 (-TW)
    Always
    Below 1 Ω
    K16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    K16-9 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER - REAR NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E149222E03
  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    O2-4 (+) - O1-1
    Always
    Below 1 Ω
    O2-2 (-) - O1-2
    Always
    Below 1 Ω
    O2-4 (+) - Body ground
    Always
    10 kΩ or higher
    O2-2 (-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O8-4 (+) - O7-1
    Always
    Below 1 Ω
    O8-2 (-) - O7-2
    Always
    Below 1 Ω
    O8-4 (+) - Body ground
    Always
    10 kΩ or higher
    O8-2 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)  

16.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 1 SPEAKER)


    E133700E12
  1. Disconnect the K16 stereo component amplifier assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-10 (RR+) - O1-1
    Always
    Below 1 Ω
    K16-4 (RR-) - O1-2
    Always
    Below 1 Ω
    K16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    K16-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-3 (RL+) - O7-1
    Always
    Below 1 Ω
    K16-9 (RL-) - O7-2
    Always
    Below 1 Ω
    K16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    K16-9 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

18.INSPECT W/ BOX NO. 1 SPEAKER ASSEMBLY


    E160619
  1. Disconnect the P14 w/ Box No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.6 to 2.4 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)
A


19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - W/ BOX NO. 1 SPEAKER)


    E146502E02
  1. Disconnect the K17 stereo component amplifier assembly connector.

  1. Disconnect the P14 w/ Box No. 1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-5 (WF1+) - P14-1
    Always
    Below 1 Ω
    K17-12 (WF1-) - P14-2
    Always
    Below 1 Ω
    K17-5 (WF1+) Body ground
    Always
    Below 1 Ω
    K17-12 (WF1-) Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)