Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1825/56    Short in Front Passenger Side - Side Squib Circuit

DTC    B1826/56    Open in Front Passenger Side - Side Squib Circuit

DTC    B1827/56    Short to GND in Front Passenger Side - Side Squib Circuit

DTC    B1828/56    Short to B+ in Front Passenger Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and the front seat side airbag RH.
This circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the side squib RH circuit.

DTC Code
Detection Condition
Trouble Area
B1825/56
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the side squib RH circuit during primary check.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1826/56
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the side squib RH circuit for 2 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1827/56
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1828/56
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C146254E43


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)
C167027E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat side airbag RH.

  1. Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1825, B1826, B1827 or B1828 is not output (for Fold Down Seat Type)
    A
    DTC B1825, B1826, B1827 or B1828 is not output (except Fold Down Seat Type)
    B
    DTC B1825, B1826, B1827 or B1828 is output
    C

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828 maybe output at this time, but they are not related to this check.



A
REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH (Click here)

B
REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH (Click here)
C


2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
C158866E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q9-1 (SFR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q9-2 (SFR-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q9-1 (SFR+) - Q9-2 (SFR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q9-1 (SFR+) - Q9-2 (SFR-)
    Always
    1 MΩ or higher
    Q9-1 (SFR+) - Body ground
    Q9-2 (SFR-) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK


3.CHECK CENTER AIRBAG SENSOR
C172068E01
  1. Connect the connectors to the front seat side airbag RH and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1825, B1826, B1827 or B1828 is output (for Column Shift Type)
    A
    DTC B1825, B1826, B1827 or B1828 is output (for Floor Shift Type)
    B
    DTC B1825, B1826, B1827 or B1828 is not output
    C

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828 maybe output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)