DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic) |
|
| P0430 | OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic) |
|

| *1 | Exhaust Manifold Sub-Assembly RH | *2 | Exhaust Manifold Sub-Assembly LH |
| *3 | Front Exhaust Pipe Assembly (TWC: Front Catalyst and Rear Catalyst) | *4 | Front No. 2 Exhaust Pipe Assembly (TWC: Front Catalyst and Rear Catalyst) |
| *5 | Air Fuel Ratio Sensor (for Bank 2 Sensor 1) | *6 | Air Fuel Ratio Sensor (for Bank 1 Sensor 1) |
| *7 | Heated Oxygen Sensor (for Bank 2 Sensor 2) | *8 | Heated Oxygen Sensor (for Bank 1 Sensor 2) |
| *9 | Center Exhaust Pipe Assembly | *10 | Tailpipe Assembly |
| Related DTCs | P0420: Catalyst Deterioration (for Bank 1) P0430: Catalyst Deterioration (for Bank 2) |
| Required Sensors/Components (Main) | A/F sensor and HO2 sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | About 30 seconds |
| MIL Operation | 1 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058, P102D, P105D (Rear oxygen sensor heater) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0607 (Rear oxygen sensor) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0401 (EGR system) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P2440 - P2447 (Secondary air injection system) P0500 (Vehicle speed sensor) P1340 (Camshaft position sensor) P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance) |
| Battery voltage | 11 V or more |
| Intake air temperature | -10°C (14°F) or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Idling | OFF |
| Engine RPM | Less than 3200 rpm |
| A/F sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 75% |
| All of following conditions (a), (b) and (c) met | - |
| (a) Mass air flow rate | 7.5 to 75 gm/s. |
| (b) Estimated front catalyst temperature | 550 to 820°C (1022 to 1508°F) |
| (c) Estimated rear catalyst temperature | 400 to 700°C (752 to 1292°F) |
| Transmission gear | 4th or higher |
| Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) | Less than 1 |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0420 or P0430 is output | A |
| P0420 or P0430 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | +12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | -12.5% | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | +12.5% | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | -12.5% | Lean | Less than 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition | Misfire | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 5.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 6.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0420 | A |
| P0430 | B |
| P0420 and P0430 | A and B |
|
| ||||
| B | ||
| ||
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
|
| ||||
| 10.CHECK EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| Go to step 9 |
| 11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 12.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (Click here).
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0420 or P0430 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 15.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0420 | A |
| P0430 | B |
| P0420 and P0430 | A and B |
|
| ||||
| B | ||
| ||