Home › ENGINE · 1UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

DTC    P0307    Cylinder 7 Misfire Detected

DTC    P0308    Cylinder 8 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks when detect immediately).
  2. Emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector assembly
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Air induction system
  14. EGR valve assembly
  15. ECM
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks when detect immediately).
  2. Emission deterioration misfire occurs (MIL illuminates).
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. At a high engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
  2. At a normal engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.



MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: MIL illuminates when misfire detected
MIL flashes immediately: When catalyst damaged misfire occurs
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
P1340 (Camshaft position sensor)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
400 to 5900 rpm
Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
All of following conditions 1, 2, 3 and 4 met
Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately)
Crankshaft 200 revolutions
1. Driving cycles
1st
2. Check mode
OFF
3. Engine RPM
Less than 2200 rpm
4. Engine load
Less than 70%

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-Related-Misfire 
Misfire rate
1.5% or more

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
Number of misfires per 200 revolutions
144 or more (varies with intake air amount and RPM)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A164725E02


A259910E03


A259911E02


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine rpm and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

    Engine RPM
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 5 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors may be a cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
  5. After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is stored.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  8. When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  9. When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel, which causes body vibration, may cause misfire DTCs to be detected.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 is output
    A
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.

    Result 
    Data List
    Techstream Display
    Proceed to
    Catalyst OT MF F/C
    AVAIL (Avail)
    A
    NOT AVL (Not Avl)
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.

  1. Allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #8 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to D.

    2. Check Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.

    3. If misfire counts are still not displayed, perform procedure "A" and "B", and then check the misfire counts again.
      Procedure A: Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using Techstream (Misfire RPM and Misfire Load)" procedures above.
      Procedure B: Read Cylinder #1 Misfire Count to Cylinder #8 Misfire Count or DTCs displayed on the Techstream.

      Result 
      Result
      Proceed to
      Most misfires occur in only 1 or 2 cylinders
      A
      3 cylinders or more have equal misfire counts
      B

      HINT:
      1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
      2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
      3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 19
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARK (SPARK TEST)
  1. Perform the spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. Perform "Inspection After Repair" after replacing the ignition coil or the spark plug (Click here).


NEXT


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER
A136305E22
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-83 (#70) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-106 (#80) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 36
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read the MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)



NG
Go to step 31
OK


16.CHECK VALVE TIMING

A214700E01

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


17.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    1. When performing the Active Test, make sure the shift lever is in P or N.
    2. The A/C switch and all accessory switches should be off.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position as follows.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    20 to 40 kPa (150 to 300 mmHg)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed



OK
Go to step 31

NG
Go to step 18

18.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



OK
Go to step 31

NG
REPLACE EGR VALVE ASSEMBLY (Click here)

19.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


20.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 36
OK


21.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


22.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read the MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)



NG
Go to step 31
OK


23.CHECK VALVE TIMING

A214700E01

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


24.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    1. When performing the Active Test, make sure the shift lever is in P or N.
    2. The A/C switch and all accessory switches should be off.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position as follows.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    20 to 40 kPa (150 to 300 mmHg)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed



OK
Go to step 31

NG
Go to step 25

25.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


26.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


27.CHECK FOR SPARK (SPARK TEST)
  1. Perform the spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. Perform "Inspection After Repair" after replacing the ignition coil or the spark plug (Click here).


NEXT


28.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


29.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E22
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-83 (#70) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-106 (#80) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


30.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


31.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of connectors and wire harness between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


32.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL
    (DTC P0300, P301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output)
    A
    NORMAL
    (DTC is not output)
    B



B
END
A


33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A164720E01
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-3 (VG) - D74-74 (VG)
    Always
    Below 1 Ω
    D7-2 (E2G) - D74-75 (E2G)
    Always
    Below 1 Ω
    D7-3 (VG) or D74-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


34.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    1. If the results of the inspection performed in steps 15 and 22 indicates no problem, proceed to the next step without replacing the mass air flow meter assembly.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).


NEXT


35.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL
    (DTC is not output)
    A
    ABNORMAL
    (DTC P0300, P301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output)
    B



B
REPLACE ECM (Click here)
A

END 

36.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)