Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Wireless Transmitter Memory Function does not Operate

for Preparation Click here


DESCRIPTION

With the ignition switch off and the driver door closed, pressing the manual lock or unlock switch on the power window regulator master switch assembly while holding a seat memory switch (M1 switch or M2 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After the registration is completed, the answer back buzzer sounds.

INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use the Techstream to check if the CAN communication system is functioning normally (Click here).

    OK:
    CAN communication DTC is not output.



NG
Go to CAN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. Check the manual door lock/unlock function by using the power window regulator master switch assembly (Click here).

    OK:
    Manual lock/unlock function operates normally.



NG
Go to POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check the wireless lock/unlock function of wireless door lock control system (Click here).

    OK:
    Wireless lock/unlock function operates normally.



NG
Go to WIRELESS DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK SEAT POSITION MEMORY FUNCTION
  1. Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (Click here).

    NOTICE:
    1. The seat position will not be recorded if the SET switch and 2 seat memory switches are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat position memory function operates normally.



NG
Go to OTHER FLOW CHART (Power Seat Position is not Memorized) (Click here)
OK


5.CHECK SEAT POSITION RESTORING FUNCTION
  1. Perform a seat position restoring function (Click here).

  1. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

    NOTICE:
    1. The seat position will not return to the memorized position if 2 seat memory switches are pressed simultaneously.
    2. If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

    OK:
    Seat position restoring function operates normally.



NG
Go to OTHER FLOW CHART (Power Seat does not Return to Memorized Position) (Click here)
OK


6.READ VALUE USING TECHSTREAM (D DOOR COURTESY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy
    Front door courtesy light switch assembly signal / ON or OFF
    ON: Driver door open
    OFF: Driver door closed
    -

OK:
ON or OFF appears on the screen according to the driver door condition.



NG
Go to LIGHTING SYSTEM (Click here)
OK


7.CHECK MEMORY CALL REGISTRATION FUNCTION
  1. When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.

    1. Turn the ignition switch is off.
    2. Press and hold the M1 or M2 seat memory switch.
    3. Driver door closed.
    4. Carry the key.

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (Click here).

OK:
Buzzer sounds normally.



NG
Go to step 9
OK


8.CHECK MEMORY CALL FUNCTION
  1. Turn the ignition switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
Go to OTHER FLOW CHART (Wireless-linked Return Function does not Operate) (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

9.REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Temporarily replace the main body ECU (driver side junction block assembly) with a new or normally functioning one.


NEXT


10.CHECK MEMORY CALL REGISTRATION FUNCTION
  1. When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.

    1. Turn the ignition switch is off
    2. Press and hold the M1 or M2 seat memory switch
    3. Driver door closed
    4. Carry the key

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (Click here).

OK:
Buzzer sounds normally.



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK

END (MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK ASSEMBLY] WAS DEFECTIVE)