Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (driver side junction block) intermittently monitors the LIN communication bus between the components related to the window and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the window and sliding roof is detected consecutively 3 times.

DTC Code
DTC Detection Condition
Trouble Area
B2325
The main body ECU (driver side junction block) detects a malfunction in the LIN communication bus between components related to the window and sliding roof consecutively 3 times.
  1. Power window regulator master switch assembly*1
  2. Front power window regulator motor assembly LH*1
  3. Front power window regulator motor assembly RH*1
  4. Sliding roof drive gear sub-assembly (Sliding Roof ECU)*2
  5. Main body ECU (driver side junction block)
  6. Harness or connector

HINT:
  1. *1: for Power Window Control System (w/ Jam Protection Function)
  2. *2: w/ Sliding Roof System


WIRING DIAGRAM


C210649E04


INSPECTION PROCEDURE

NOTICE:
When using the Techstream with the ignition switch OFF to troubleshoot:
Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

HINT:
When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output reoccurs
    A
    DTC B2325 output does not reoccur
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    for Power Window Control System (w/ Jam Protection Function) and w/ Sliding Roof System, or for Power Window Control System (w/ Jam Protection Function) and w/o Sliding Roof System
    A
    for Power Window Control System (w/o Jam Protection Function) and w/ Sliding Roof System
    B



B
Go to step 15
A


4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH)


    E160673E02
  1. Disconnect the N2 power window regulator master switch assembly connector.

  1. Disconnect the N12 front power window regulator motor assembly LH connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-7 (LIN2) - N12-9 (LIN)
    Always
    Below 1 Ω
    N2-7 (LIN2) or N12-9 (LIN) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N2-7 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

C210650E03

  1. Disconnect the J2 main body ECU (driver side junction block) connector.

  1. Disconnect the N2 power window regulator master switch assembly connector.

  1. Disconnect the M11 front power window regulator motor assembly RH connector.

  1. w/ Sliding Roof System:
    Disconnect the W3 sliding roof drive gear sub-assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J2-10 (LIN2) - N2-6 (LIN1)
    Always
    Below 1 Ω
    J2-10 (LIN2) - M11-9 (LIN)
    J2-10 (LIN2) - W3-3 (LIN)*
    J2-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    *: w/ Sliding Roof System

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J2-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ Sliding Roof System
    A
    w/o Sliding Roof System
    B



B
Go to step 9
A


7.CLEAR DTC
  1. Reconnect the J2 main body ECU (driver side junction block) connector.

  1. Reconnect the N2 power window regulator master switch assembly connector.

  1. Reconnect the M11 front power window regulator motor assembly RH connector.

  1. Disconnect the W3 sliding roof drive gear sub-assembly connector.

  1. Clear the DTC (Click here).


NEXT


8.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output reoccurs
    A
    DTC B2325 output does not reoccur
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)
A


9.CLEAR DTC
  1. w/ Sliding Roof System:
    Reconnect the W3 sliding roof drive gear sub-assembly connector.

  1. Disconnect the N12 power window regulator motor assembly LH connector.

  1. Clear the DTC (Click here).


NEXT


10.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output reoccurs
    A
    DTC B2325 output does not reoccur
    B



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


11.CLEAR DTC
  1. Reconnect the N12 power window regulator motor assembly LH connector.

  1. Disconnect the N2 power window regulator master switch assembly connector.

  1. Clear the DTC (Click here).


NEXT


12.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output reoccurs
    A
    DTC B2325 output does not reoccur
    B



B
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
A


13.CLEAR DTC
  1. Reconnect the N2 power window regulator master switch assembly connector.

  1. Disconnect the M11 power window regulator motor assembly RH connector.

  1. Clear the DTC (Click here).


NEXT


14.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output reoccurs
    A
    DTC B2325 output does not reoccur
    B



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK) 

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)

B353651E01

  1. Disconnect the J2 main body ECU (driver side junction block) connector.

  1. Disconnect the W3 sliding roof drive gear sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J2-10 (LIN2) - W3-3 (LIN)
    Always
    Below 1 Ω
    J2-10 (LIN2) or W3-3 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)


    B163105E09
  1. Disconnect the W3 sliding roof drive gear sub-assembly connector.

  1. Measure the resistance and voltage according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-8 (E) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    W3-10 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one (Click here).

  1. Clear the DTC (Click here).


NEXT


18.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 output does not reoccur
    A
    DTC B2325 output reoccurs
    B



B
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)
A

END (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY [SLIDING ROOF ECU] IS DEFECTIVE)