Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Door Control Switch Circuit

for Preparation Click here


DESCRIPTION

for Driver Side:
  1. When the lock side of the door control switch is pressed, continuity is established between terminal 1 (for regular cab) or 2 (except regular cab) and terminal 7 (for regular cab) or 1 (except regular cab) of the switch. When the unlock side of the switch is pressed, continuity is established between terminal 9 and terminal 7 (for regular cab) or 1 (except regular cab). Terminals L1 and UL1 of the main body ECU are connected to the door control switch, and door lock/unlock request signals (by door control switch operation) are input to the ECU. The main body ECU constantly applies voltage to terminal 1 (for regular cab) or 2 (except regular cab) of the door control switch via terminal L1. When the door control switch is operated to lock all doors, current flows from terminal L1 to terminal 1 (for regular cab) or 2 (except regular cab). The main body ECU determines that this is a door lock request signal input. The main body ECU also applies constant voltage to terminal 9 of the door control switch via terminal UL1. When the door control switch is operated to unlock the doors, current flows from terminal UL1 to terminal 9. The main body ECU determines that this is a door unlock request signal input.
for Passenger Side:
  1. When the lock side of the door control switch is pressed, continuity is established between terminal 4 and terminal 3 of the switch. When the unlock side of the switch is pressed, continuity is established between terminal 2 and terminal 3. Terminals L1 and UL1 of the main body ECU are connected to the door control switch, and door lock/unlock request signals (by door control switch operation) are input to the ECU. The main body ECU constantly applies voltage to terminal 4 of the door control switch via terminal L1. When the door control switch is operated to lock all doors, current flows from terminal L1 to terminal 4. The main body ECU determines that this is a door lock request signal input. The main body ECU also applies constant voltage to terminal 2 of the door control switch via terminal UL1. When the door control switch is operated to unlock the doors, current flows from terminal UL1 to terminal 2. The main body ECU determines that this is a door unlock request signal input.

WIRING DIAGRAM


E144956E12


E144956E05


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH)
  1. Check the Data List to ensure proper functioning of the door control switch.

    Main Body 
    Tester Display
    Measurement item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door control switch lock signal
    / ON or OFF
    ON: Door control switch is pushed to lock position
    OFF: Door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door control switch unlock signal
    / ON or OFF
    ON: Door control switch is pushed to unlock position
    OFF: Door control switch is not pushed
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Driver Side)
    B
    NG (for Passenger Side)
    C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH

B265509E01

  1. Remove the master switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Regular Cab:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (L) - 7 (E)
    Lock
    Below 1 Ω
    1 (L) - 7 (E)
    OFF (Free)
    10 kΩ or higher
    9 (UL) - 7 (E)
    9 (UL) - 7 (E)
    Unlock
    Below 1 Ω
    except Regular Cab:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (L) - 1 (E)
    Lock
    Below 1 Ω
    2 (L) - 1 (E)
    OFF (Free)
    10 kΩ or higher
    9 (UL) - 1 (E)
    9 (UL) - 1 (E)
    Unlock
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (DOOR LOCK SWITCH - MAIN BODY ECU)

E144704E04

  1. Disconnect the N2 switch connector.

  1. Disconnect the DD ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Regular Cab:
    Tester Connection
    Condition
    Specified Condition
    N2-1 (L) - DD-49 (L1)
    Always
    Below 1 Ω
    N2-9 (UL) - DD-52 (UL1)
    N2-7 (E) - Body ground
    DD-49 (L1) - Body ground
    Always
    10 kΩ or higher
    DD-52 (UL1) - Body ground
    except Regular Cab:
    Tester Connection
    Condition
    Specified Condition
    N2-2 (L) - DD-49 (L1)
    Always
    Below 1 Ω
    N2-9 (UL) - DD-52 (UL1)
    N2-1 (E) - Body ground
    DD-49 (L1) - Body ground
    Always
    10 kΩ or higher
    DD-52 (UL1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.INSPECT DOOR CONTROL SWITCH
B164735E02
  1. Remove the door control switch (Click here ).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (L) - 3 (E)
    Lock
    Below 1 Ω
    4 (L) - 3 (E)
    OFF
    10 kΩ or higher
    2 (UL) - 3 (E)
    2 (UL) - 3 (E)
    Unlock
    Below 1 Ω



NG
REPLACE DOOR CONTROL SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT DOOR CONTROL SWITCH RH - MAIN BODY ECU AND BODY GROUND)

E147842E01

  1. Disconnect the M5 switch connector.

  1. Disconnect the DD ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M5-4 (L) - DD-49 (L1)
    Always
    Below 1 Ω
    M5-2 (UL) - DD-40 (UL1)
    M5-3 (E) - Body ground
    DD-49 (L1) - Body ground
    Always
    10 kΩ or higher
    DD-40 (UL1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU