Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the AUTO UP/DOWN function does not operate, the cause may be one or more of the following:
  1. The ECU in the front passenger side motor determines that the front passenger side motor has not been initialized.
  2. The power window regulator switch assembly has a malfunction.
  3. The Hall-IC in the front passenger side motor has a malfunction.
  4. The wiring between the power window regulator switch assembly and the front passenger side motor is open or shorted.

WIRING DIAGRAM


B231468E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC B2311 is output
    B
    DTC B2312 is output
    C
    DTC B2313 is output
    D
    LIN communication system DTCs are output
    E



B
GO TO DTC (B2311) (Click here)

C
GO TO DTC (B2312) (Click here)

D
GO TO DTC (B2313) (Click here)

E
GO TO LIN COMMUNICATION SYSTEM (Click here)
A


2.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the manual UP/DOWN function using the power window regulator switch assembly can operate the front passenger side door power window (Click here).

    OK:
    Manual UP/DOWN function operates normally.



NG
GO TO FLOWCHART (FRONT PASSENGER SIDE MOTOR CIRCUIT) (Click here)
OK


3.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
  1. Use the Data List to check if the front passenger side motor is functioning properly.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto UP/DOWN switch signal / ON or OFF
    ON: Power window regulator switch assembly operated
    OFF: Power window regulator switch assembly not operated
    -

OK:
The Techstream display changes when power window regulator switch assembly is operated.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)


    B184455E17
  1. Disconnect the M10 switch connector.

  1. Disconnect the M11 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M10-8 (AUTO) - M11-4 (AUTO)
    Always
    Below 1 Ω
    M10-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B231347E03
  1. Remove the power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    AUTO UP/DOWN operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)