Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › AIR FUEL RATIO SENSOR
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233900 AIR FUEL RATIO SENSOR A

1UR-FE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A215439

Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.


b.
A215440E02
0.736,0.965 0.930,1.127 0.193,0.163 10 *a 2.949,1.469 3.253,1.648 0.304,0.179 10 SST 2.907,1.551 2.774,1.551 2.774,1.551 2.378,0.832 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

Text in Illustration
*a Fulcrum length

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




Hide 17450B 2.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 89467B 3.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A215442

Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.


b.
A215443E02
2.655,1.445 2.850,1.627 0.195,0.183 10 *a 0.734,1.834 1.078,1.997 0.343,0.163 10 SST 1.054,0.811 0.9,1.628 0.9,1.628 0.9,1.821 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY