Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0451  Evaporative Emission Control System Pressure Sensor Range / Performance  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0451 Canister pressure sensor noise Sensor output voltage fluctuates frequently within certain time period.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

EVAP monitoring (ignition switch off)

·

Engine running


2 trip
P0451 Canister pressure sensor becomes fixed/flat Sensor output voltage does not vary in a certain time period.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

EVAP monitoring (ignition switch off)


2 trip
P0452 Canister pressure sensor low input EVAP pressure Below 42.1 kPa for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip
P0453 Canister pressure sensor high input EVAP pressure higher than 123.8 kPa for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in the EVAP (Evaporative Emission) system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>EVAP System).

MONITOR DESCRIPTION

A115543E70
4.552,3.302 4.969,3 true 4.521,1.427 4.958,1.052 true 0.094,0.083 3.083,0.292 2.99,0.208 10 Canister Pressure Sensor Specification: 5.115,3.344 5.792,3.604 0.677,0.26 10 Pressure 1.302,1.021 2.365,1.281 1.063,0.26 10 Output Voltage 1.698,1.448 2.281,1.708 0.583,0.26 10 4.900 V 1.698,1.917 2.281,2.177 0.583,0.26 10 4.423 V 1.698,2.615 2.281,2.875 0.583,0.26 10 1.425 V 1.698,3.094 2.281,3.354 0.583,0.26 10 0.450 V 5.01,2.917 6.135,3.177 1.125,0.26 10 Malfunction Area 5,0.958 6.125,1.219 1.125,0.26 10 Malfunction Area 3.844,2.292 4.813,2.552 0.969,0.26 10 Usable Range 1.833,4.25 6.656,4.479 4.823,0.229 10 Standard atmospheric pressure is 101.3 kPa(abs) [760 mmHg(abs)] 1.833,4.031 2.292,4.292 0.458,0.26 10 HINT: 3.583,3.458 3.969,3.844 0.385,0.385 10 115 (862) 2.896,3.458 3.281,3.844 0.385,0.385 10 60 (450) 4.344,3.448 5.333,3.906 0.99,0.458 10 kPa(abs) [mmHg(abs)]

1.

DTC P0451: Canister pressure sensor noise or fixed/flat

If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as noise from the canister pressure sensor, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (2 trip detection logic).

Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC (both malfunctions are detected by 2 trip detection logic).

2.

DTC P0452: Canister pressure sensor voltage low

If the canister pressure sensor output [pressure] is below 42.1 kPa-a (315.9 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

3.

DTC P0453: Canister pressure sensor voltage high

If the canister pressure sensor output [pressure] is higher than 123.8 kPa-a (928.4 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


MONITOR STRATEGY

Required Sensors/Components Canister pump module
Frequency of Operation Continuous
Duration Within 15 seconds: P0451 sensor noise
Within 2 minutes: P0451 sensor fixed/flat
0.5 seconds: P0452 and P0453
MIL Operation Immediate: P0452 and P0453
2 driving cycles: P0451
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0451 (Noise Monitor)
Monitor runs whenever following DTCs not present P0452, P0453 (EVAP system)
Atmospheric pressure (absolute pressure) 70 to 111 kPa-a (525 to 833 mmHg-a)
Battery voltage 10.5 V or higher
Intake air temperature 4.4 to 40°C (40 to 104°F)
Either of following conditions met A or B
A. Engine condition Running
B. Time after key off 5, 7 or 9.5 hours

P0451 (Fixed/Flat Monitor)
Monitor runs whenever following DTCs not present P0452, 0453 (EVAP system)
Battery voltage 10.5 V or higher
Intake air temperature 4.4 to 40°C (40 to 104°F)
Atmospheric pressure (absolute pressure) 70 to 111 kPa-a (525 to 833 mmHg-a)
Time after key off 5, 7 or 9.5 hours

P0452 and P0453
Monitor runs whenever following DTCs not present None
Battery voltage 8 V or higher
Starter OFF
Either of following conditions met (a) or (b)
(a) Ignition switch ON
(b) Soak timer ON

TYPICAL MALFUNCTION THRESHOLDS

P0451: Canister Pressure Sensor Noise
Frequency that EVAP pressure changes 0.3 kPa-g (2.25 mmHg-g) or higher 10 times or more in 10 seconds

P0451: Canister Pressure Sensor Voltage Fixed
EVAP pressure change during reference pressure measurement Below 0.65 kPa-a (4.87 mmHg-a)

P0452: Canister Pressure Sensor Low Voltage
EVAP pressure Below 42.1 kPa-a (315.8 mmHg-a)

P0453: Canister Pressure Sensor High Voltage
EVAP pressure Higher than 123.8 kPa-a (928.6 mmHg-a)

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).



1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

8.

After the "Evaporative System Check" is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

9.

Input the DTC: P0451, P0452 or P0453.

10.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


11.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.

·

The Techstream is required to conduct the following diagnostic troubleshooting procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON (do not start the engine).


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.


g.

Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

Result
Result Test Result Suspected Trouble Area Proceed to
P0451 - Canister pressure sensor C
P0452 Below 42.1 kPa-a (315.8 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 Higher than 123.8 kPa-a (928.6 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B



A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
U151415E02
1.521,2.677 1.479,2.135 false 0.219,0.979 0.542,1.156 0.323,0.177 10 false D74 0.104,0.052 2.469,0.406 2.365,0.354 10 false Front view of wire harness connector: (to ECM) 1.292,2.719 1.833,2.938 0.542,0.219 10 false PPMP

a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
D74-121 (PPMP) - Body ground Always 10 Ω or less
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in canister pressure sensor circuit


A
D74-121 (PPMP) - Body ground Always 10 kΩ or higher
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in ECM circuit


B



A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
D74-121 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
D74-121 (PPMP) - Body ground Always 10 Ω or less Short in wire harness/connector (ECM - Canister pressure sensor) B



A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
U151758E01
4.723,0.016 6.858,0.408 2.135,0.392 10 Front view of harness connector: (to Canister Pump Module) 4.833,2.096 5.169,2.252 0.336,0.156 10 VCC 5.501,2.096 5.934,2.252 0.434,0.156 10 VOUT 6.383,2.096 6.817,2.252 0.434,0.156 10 SGND 5.017,2.068 5.576,1.503 false 5.694,2.084 5.712,1.501 false 5.877,1.501 6.33,2.084 false 5.505,0.633 5.805,0.803 0.299,0.170 10 R12

a.

Disconnect the canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R12-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R12-6 (VCC) - Body ground Ignition switch ON 4.5 to 5.5 V
R12-7 (VOUT) - Body ground Ignition switch ON 4.5 to 5.5 V



Result
Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and resistance outside standard ranges Open in wire harness/connector (ECM - Canister pressure sensor) B


A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
5.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



A289733E10
1.677,2.938 1.479,3.323 1.479,3.323 1.354,3.323 false 3.74,1.708 3.104,3.042 3.104,3.042 2.969,3.042 false 4.771,2.135 4.844,2.375 4.844,2.375 4.938,2.375 false 4.573,4.125 4.792,4.354 4.792,4.354 4.875,4.354 false 5.146,1.448 5.313,1.042 5.313,1.042 5.448,1.042 false 4.01,2.958 4.135,2.792 4.135,2.792 4.24,2.792 false 2.74,2.938 2.948,3.125 0.208,0.188 10 false *2 4.24,2.729 4.427,2.917 0.188,0.188 10 false *6 4.958,2.25 5.146,2.438 0.188,0.188 10 false *4 4.927,4.25 5.146,4.438 0.219,0.188 10 false *5 5.083,2.813 5.271,3 0.188,0.188 10 false *a 3.74,0.813 3.927,1 0.188,0.188 10 false *a 1.135,3.208 1.354,3.396 0.219,0.188 10 false *1 5.5,0.948 5.74,1.115 0.24,0.167 10 false *3

Text in Illustration
*1 Fuel Tank *2 Fuel Tank Vent Hose
*3 Canister Assembly *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *6 Canister Outlet Hose
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
HINT:

If the exhaust tailpipe has been removed, go to the next step before reinstalling it.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
7.REPLACE ECM

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0451, P0452 or P0453.


k.

Check the DTC judgment result.

Result:
Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit






NEXT

END