Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P1340  Camshaft Position Sensor "A" (Bank 1 Sensor 2)  P1342  Camshaft Position Sensor "A" Low Input (MRE)  P1343  Camshaft Position Sensor "A" High Input (MRE)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magnetoresistive Element).

The camshaft drive gear (LH) has 3 teeth on its outer circumference. When the camshaft gear rotates, the air gap between the protrusion on the gear and the MRE changes. The change affects the magnetic field and results in changes in the resistance of the MRE.

The crankshaft sensor plate has 34 teeth and is mounted on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

DTC No. DTC Detection Condition Trouble Area
P1340 No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing plate LH

·

ECM


No camshaft position sensor signal to ECM with engine speed 600 rpm or more (1 trip detection logic)
P1342 Output voltage of camshaft position sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
P1343 Output voltage of camshaft position sensor more than 4.7 V for 4 seconds
(1 trip detection logic)

MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor. Also, when the sensor output voltage remains below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P1340: Camshaft position sensor verify pulse input
P1340: Camshaft position / Crankshaft position misalignment
P1342: Camshaft position sensor range check (low voltage)
P1343: Camshaft position sensor range check (high voltage)
Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor, Engine speed sensor
Frequency of Operation Continuous
Duration 4 seconds:
P1340 camshaft position sensor verify pulse input
P1342: Camshaft position sensor range check (low voltage)
P1343: Camshaft position sensor range check (high voltage)
5 seconds:
P1340 camshaft position / crankshaft position misalignment
MIL Operation 2 driving cycles: P1340 camshaft position sensor verify pulse input
Immediate: P1340 camshaft position / crankshaft position misalignment and P1342, P1343 camshaft position sensor range check
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P1340 Camshaft Position Sensor Verify Pulse Input
Monitor runs whenever following DTCs not present None
Starter ON (Not including when starter turned ON multiple times)
Minimum battery voltage while starter ON Less than 11 V

P1340 Camshaft Position / Crankshaft Position Misalignment
Monitor runs whenever following DTCs not present P0342, P0343 (VVT sensor)
P1342, P1343 (Camshaft position sensor)
Engine RPM 600 rpm or more
Starter OFF
Camshaft position sensor range 0.3 to 4.7 V

P1342, P1343 Camshaft Position Sensor Range Check
Monitor runs whenever following DTCs not present P0340 (VVT sensor)
P1340 (Camshaft position sensor)
Time after ignition switch off to ON 2 seconds or more
Battery voltage 8 V or more
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P1340 Camshaft Position Sensor Verify Pulse Input
Camshaft position signal No signal

P1340 Camshaft Position / Crankshaft Position Misalignment
Camshaft position and crankshaft position phase Misaligned

P1342 Camshaft Position Sensor Range Check
Camshaft position sensor voltage Less than 0.3 V

P1343 Camshaft Position Sensor Range Check
Camshaft position sensor voltage More than 4.7 V

COMPONENT OPERATING RANGE

Camshaft position sensor signal
·

Camshaft position sensor voltage fluctuates when the camshaft rotates

·

3 signals per revolution of camshaft



CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P1340, P1342 or P1343.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.


13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165785E01
5.311,0.997 5.710,1.153 0.399,0.156 10 VCV2 5.311,1.543 5.539,1.699 0.229,0.156 10 G2 5.311,2.086 5.600,2.242 0.289,0.156 10 G2- 5.038,0.923 5.229,1.079 0.191,0.156 10 66 5.038,1.46 5.229,1.616 0.191,0.156 10 90 5.038,1.997 5.229,2.153 0.191,0.156 10 89 2.44,0.998 2.670,1.150 0.230,0.151 10 VC 2.44,1.541 2.670,1.692 0.230,0.151 10 G2 2.44,2.078 2.670,2.229 0.230,0.151 10 G- 2.745,0.918 2.887,1.073 0.142,0.155 10 3 2.745,1.455 2.887,1.610 0.142,0.155 10 1 2.745,1.992 2.887,2.147 0.142,0.155 10 2 5.795,2.623 6.090,2.779 0.295,0.156 10 D74 5.795,2.763 6.136,2.919 0.341,0.156 10 ECM 1.329,2.354 1.555,2.510 0.225,0.156 10 D6 1.329,2.494 2.981,2.660 1.651,0.165 10 Camshaft Position Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
U151397E02
1.99,2.188 2.479,2.74 false 0.594,2.104 0.844,2.302 0.25,0.198 10 false D6 0.333,0.167 2.698,0.531 2.365,0.365 10 false Front view of wire harness connector: (to Camshaft Position Sensor) 2.438,2.781 2.781,2.948 0.344,0.167 10 false VC

a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D6-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
A379451E01
1.677,0.906 2.063,1.146 0.385,0.24 4.563,0.896 4.99,1.156 0.427,0.26 1.635,1.813 1.281,2.167 true 1.896,1.813 2.385,2.229 true 3.979,1.896 3.667,2.302 true 4.042,1.896 4.354,2.333 true 0.563,0.094 2.865,0.469 2.302,0.375 10 false Front view of wire harness connector: (to Camshaft Position Sensor) 3.688,0.094 5.99,0.469 2.302,0.375 10 false Front view of wire harness connector: (to ECM) 1.771,0.938 2.083,1.135 0.313,0.198 10 false D6 4.646,0.938 5,1.135 0.354,0.198 10 false D74 1.135,2.188 1.448,2.385 0.313,0.198 10 false G2 2.417,2.25 2.729,2.448 0.313,0.198 10 false G- 3.552,2.313 3.865,2.51 0.313,0.198 10 false G2- 4.313,2.354 4.625,2.552 0.313,0.198 10 false G2

a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D6-1 (G2) - D74-90 (G2) Always Below 1 Ω
D6-2 (G-) - D74-89 (G2-) Always Below 1 Ω
D6-1 (G2) or D74-90 (G2) - Body ground Always 10 kΩ or higher
D6-2 (G-) or D74-89 (G2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
BR03795E98
2.163,1.53 2.360,1.731 0.197,0.201 10 *c 0.49,1.765 0.757,1.973 0.267,0.208 10 *a 2.673,1.765 2.940,1.973 0.267,0.208 10 *b 2.833,1.978 3.414,2.144 0.581,0.165

a.

Check the camshaft position sensor installation.

OK:

The camshaft position sensor is installed properly.




OK

4.INSPECT CAMSHAFT TIMING PLATE (SENSOR PLATE TOOTH)

NG

4.INSPECT CAMSHAFT TIMING PLATE (SENSOR PLATE TOOTH)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

5.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P1340, P1342 and/or P1343 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B