Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › ENGINE UNIT
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234043 ENGINE UNIT A

1UR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 4.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 12185 5.REMOVE OIL FILLER CAP HOUSING

a.
A214596

Remove the 2 bolts, filler cap housing and gasket.


Hide 19100P 6.REMOVE SPARK PLUG

a.

Using a 16 mm plug wrench, remove the 8 spark plugs.


Hide 7.REMOVE VVT SENSOR

a.
A214597

LH:

Remove the 2 bolts and 2 VVT sensors.


b.
A214598

RH:

Remove the 2 bolts and 2 VVT sensors.


Hide 11102A 8.REMOVE CAMSHAFT POSITION SENSOR

a.
A214599

Remove the bolt and camshaft position sensor.


Hide 19312 9.REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR

A161907

a.

Remove the 2 bolts and sensor protector.


Hide 15100R 10.REMOVE CRANKSHAFT POSITION SENSOR

a.
A161908

Remove the bolt and crankshaft position sensor.


Hide 15330B 11.REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

a.
A214600

LH:

Remove the 2 bolts and 2 oil control valves.


b.
A214601

RH:

Remove the 2 bolts and 2 oil control valves.


Hide 11202 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A210021

Remove the 14 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).


Hide 11201 13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A210024

Remove the 14 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162526

Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).


Hide 15678A 14.REMOVE OIL CONTROL VALVE FILTER

A164313E05
2.49,0.885 2.49,1.302 false 2.792,0.115 2.948,0.115 2.948,0.115 3.104,0.896 true 1.708,0.406 2.167,0.406 2.167,0.406 2.813,0.781 true 2.313,1.344 2.708,1.583 0.396,0.24 10 false Filter 1.219,0.323 1.813,0.51 0.594,0.188 10 true Gasket 1.063,0.031 2.917,0.24 1.854,0.208 10 true Cylinder Head Cover Spacer

a.

LH:

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


b.
A164314E05
0.917,0.781 0.917,1.208 false 0.281,0.781 0.635,0.104 0.635,0.104 0.771,0.104 true 0.625,0.677 0.99,0.396 0.99,0.396 1.917,0.396 true 0.75,1.229 1.125,1.438 0.375,0.208 10 false Filter 1.958,0.292 2.458,0.5 0.5,0.208 10 true Gasket 0.802,0 2.656,0.292 1.854,0.292 10 true Cylinder Head Cover Spacer

RH:

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


Hide 11193 15.REMOVE SPARK PLUG TUBE GASKET

U151527E02
1.563,0.375 1.729,0.375 1.729,0.375 1.927,1.219 true 2.167,1.292 2.458,1.625 0.292,0.333 10 true Pry 1.167,0.271 1.646,0.719 0.479,0.448 10 true Tape

a.

Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.


b.

Using a screwdriver, pry out the gaskets.

NOTICE:

Be careful not to damage the cylinder head cover.


HINT:
·

Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.

·

Tape the screwdriver tip before use.




Hide 16100 16.REMOVE WATER PUMP ASSEMBLY

Hide 11302 17.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 19.REMOVE FRONT CRANKSHAFT OIL SEAL

a.

Place the timing chain cover on wooden blocks.


b.
A214602E05
1.25,1.042 1.25,2.021 false 1.24,1.021 2.396,1.99 true 0.719,1.031 1.865,1.031 false 0.042,0.938 0.604,1.302 0.563,0.365 10 false Wooden Block

Place the oil pump on a wooden block.


c.

Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 20.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.

Temporarily install the pulley set bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.


A214603E05
3.5,4.76 4.031,5.01 4.031,5.01 4.031,5.125 false 3.667,4.344 4.052,3.969 4.052,3.969 4.177,3.969 false 0.646,0.271 0.458,0.271 0.458,0.271 0.563,0.844 false 1.51,0.271 1.729,0.271 1.729,0.271 1.677,0.74 false 5.667,0.271 5.5,0.271 5.5,0.271 5.583,0.771 false 6.531,0.281 6.781,0.281 6.781,0.281 6.729,0.896 false 0.542,5.583 0.813,6.135 0.813,6.135 1.365,5.583 false 0.333,4.375 0.229,4.375 0.229,4.375 0.531,5.323 false 0.531,3.344 1.052,4.052 1.052,4.052 1.375,3.438 false 5.854,5.552 6.115,6.135 6.115,6.135 6.583,5.552 false 5.323,4.667 5.073,4.667 5.073,4.667 5.542,5.25 false 6.375,4.448 6.885,4.448 6.885,4.448 6.615,5.365 false 5.479,3.719 6.01,4.135 6.01,4.135 6.469,3.51 false 0.615,3.146 0.365,2.313 0.365,2.313 0.469,2.313 false 1.74,3.125 2.042,2.333 2.042,2.333 1.906,2.333 false 5.417,3.229 5.188,2.448 5.188,2.448 5.281,2.448 false 6.563,3.281 6.865,2.49 6.865,2.49 6.719,2.49 false 1.396,5.365 1.74,4.948 1.74,4.948 1.646,4.948 false 1.667,5.26 2.083,4.688 2.083,4.688 1.99,4.688 false 1.813,5.281 2,5.5 2,5.5 2,5.771 false 5.427,5.229 5.313,5.385 5.313,5.385 5.313,5.615 false 5.563,4.917 5.448,4.917 5.448,4.917 5.813,5.375 false 3.656,5.135 4.51,5.302 0.854,0.167 10 false Timing Mark 4.208,3.896 4.521,4.094 0.313,0.198 10 false Key 0.698,0.198 1.531,0.375 0.833,0.177 10 false Timing Mark 5.719,0.208 6.552,0.385 0.833,0.177 10 false Timing Mark 0.198,6.167 1.573,6.375 1.375,0.208 10 false Timing Mark Position 0.531,4.083 1.771,4.333 1.24,0.25 10 true Knock Pin Position 5.385,4.583 6.615,4.833 1.229,0.25 10 true Approximately 45° 5.615,4.813 6.844,5.063 1.229,0.25 10 false Approximately 32° 5.5,6.135 6.875,6.344 1.375,0.208 10 false Timing Mark Position 5.438,4.094 6.688,4.344 1.25,0.25 10 true Knock Pin Position 0.521,2.25 1.896,2.427 1.375,0.177 10 false Timing Mark Position 5.385,2.396 6.76,2.573 1.375,0.177 10 false Timing Mark Position 0.365,4.313 1.594,4.563 1.229,0.25 10 true Approximately 2° 0.51,4.844 1.74,5.094 1.229,0.25 10 false Approximately 16° 0.823,4.625 2.052,4.875 1.229,0.25 10 true Approximately 45° 1.708,5.792 2.198,6.167 0.49,0.375 10 false Toward Ceiling 5.031,5.615 5.521,5.99 0.49,0.375 10 false Toward Ceiling 5.177,4.323 6.406,4.615 1.229,0.292 10 true Approximately 18° 3.104,0.99 4.125,1.365 1.021,0.375 10 false Toward Ceiling


Hide 13540 21.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

Hide 13559 22.REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH

Hide 13540 26.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

Hide 13559 27.REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH

Hide 13521A 31.REMOVE CRANKSHAFT TIMING GEAR KEY

A214622

a.

Using a screwdriver, remove the 2 timing gear keys from the crankshaft.


Hide 11104A 33.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 11103C 35.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 13801 36.REMOVE VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 32 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 37.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 32 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 38.REMOVE VALVE STEM CAP

a.

Remove the 32 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11116 41.REMOVE CYLINDER HEAD GASKET LH

Hide 11115 42.REMOVE CYLINDER HEAD GASKET RH

Hide 11445 43.REMOVE CYLINDER BLOCK WATER JACKET SPACER

A214628

a.

Remove the 2 water jacket spacers from the cylinder head.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



Hide 12209E 44.REMOVE OIL RETURN PIPE GASKET

a.
A214629

Using a screwdriver, pry out the oil return pipe gasket.

HINT:

Tape the screwdriver tip before use.



Hide 12203A 45.REMOVE VENTILATION PIPE GASKET

a.
A214630

Using a screwdriver, pry out the ventilation pipe gasket.

HINT:

Tape the screwdriver tip before use.



Hide 16877 46.REMOVE NO. 1 HEAT EXCHANGER COVER

a.
A214631E05
2.698,1.76 2.979,2.042 0.281,0.281 9 true Nut 0.302,1.74 0.594,2.031 0.292,0.292 9 true Nut

Remove the 12 bolts and 2 nuts.


b.
A214632

Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.



Hide 12102A 47.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A160720E01
2.883,0.527 3.151,0.700 0.268,0.173 10 Nut 1.362,1.675 1.732,1.843 0.37,0.168 1.443,1.701 1.711,1.874 0.268,0.173 10 Nut

Remove the 14 bolts and 2 nuts.


b.
A120816

Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 12101 48.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

a.
A160721E03
2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.813 1.396,0.969 0.25,0.156 10 true Nut

Remove the 14 bolts and 2 nuts.

HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



b.
A214633E01
0.126,0 0.505,0.370 0.378,0.370 10 LH Side: 0.126,1.666 0.539,2.025 0.413,0.359 10 RH Side:

Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.


HINT:

Tape the screwdriver tip before use.



Hide 12121 49.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A160723

Remove the 7 bolts and baffle plate.


Hide 15104 50.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A160724

Remove the 2 bolts, oil strainer and O-ring.


Hide 11381 51.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A145612

Remove the 6 bolts and oil seal retainer.


b.
A380017

Using a screwdriver, pry out the oil seal retainer.

HINT:

Tape the screwdriver tip before use.



Hide 12109A 52.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY

a.
A160728

Remove the bolt and oil drain pipe.


b.

Remove the O-ring.


Hide 11381A 53.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A145614E01
2.581,0.779 3.154,1.116 0.573,0.336 10 Wooden Block 2.249,1.066 2.53,0.945 false

Place the oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the oil seal.


Hide 54.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 55.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.