Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) or more for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)

(a) Vehicle speed 20 km/h (12.4 mph) or more

(b) Engine speed 1000 rpm or more

(c) STA signal ON


·

Park/Neutral Position (PNP) switch

·

Starter relay circuit

·

Ignition switch assembly

·

ECM



MONITOR STRATEGY

Related DTCs P0617: Starter signal
Required Sensors/Components (Main) ST relay, PNP switch and ignition switch
Required Sensors/Components (Related) Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor
Frequency of Operation Continuous
Duration 20 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Battery voltage 10.5 V or more
Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A199310E01
1.226,1.979 1.604,2.156 0.378,0.177 10 Idling 0.456,2.238 1.653,2.408 1.198,0.170 10 Ignition Switch ON 0.435,0.603 1.559,0.783 1.125,0.180 10 24 km/h (15 mph) 2.393,2.851 3.076,3.167 0.684,0.316 10 5 seconds or more 3.427,2.938 4.699,3.103 1.272,0.165 10 20 seconds or more 2.004,2.336 2.197,2.525 0.193,0.188 10 [A] 2.586,2.125 2.796,2.297 0.210,0.172 10 [B] 3.02,3.309 3.259,3.492 0.239,0.184 10 [C] 4.03,0.457 4.257,0.625 0.227,0.168 10 [D] 4.905,3.342 5.139,3.510 0.234,0.168 10 [E]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0617.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



12.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


13.

Check the DTC judgment result [E].

14.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A159967E16
6.292,4.208 6.729,4.448 0.438,0.24 10 false ECM 5.927,0.76 6.333,0.927 0.406,0.167 10 false NSW 5.938,1.281 6.292,1.479 0.354,0.198 10 false STA 5.604,0.76 5.927,0.927 0.323,0.167 10 false D74 5.604,1.156 5.948,1.354 0.344,0.198 10 false A24 5.646,0.969 5.833,1.115 0.188,0.146 10 false 46 5.604,0.563 5.896,0.75 0.292,0.188 10 false 120 3.25,1.479 5.167,1.667 1.917,0.188 10 false Park / Neutral Position Switch 3.729,1.302 4.042,1.469 0.313,0.167 10 false D35 3.323,2.792 3.542,2.979 0.219,0.188 10 false ST 1.229,3.052 1.448,3.24 0.219,0.188 10 false ST 1.219,1.729 1.448,1.896 0.229,0.167 10 false J9 1.219,1.854 2.219,2.063 1,0.208 10 false Ignition Switch 1.906,1.281 2.281,1.448 0.375,0.167 10 false ST2 1.167,1.26 1.573,1.458 0.406,0.198 10 false AM2 0.469,1.927 0.802,2.094 0.333,0.167 10 false AM2 1.01,1.229 1.125,1.385 0.115,0.156 10 false 5 2.26,1.271 2.375,1.427 0.115,0.156 10 false 7 1.365,5.552 1.823,5.74 0.458,0.188 10 false Battery 3.719,5.438 4.25,5.656 0.531,0.219 10 false Starter 3.615,4.99 3.875,5.167 0.26,0.177 10 false E5 3.906,4.802 4.156,4.958 0.25,0.156 10 false E3 4.042,4.615 4.177,4.771 0.135,0.156 10 false 1 3.646,4.802 3.781,4.958 0.135,0.156 10 false 1 4,1.042 4.115,1.198 0.115,0.156 10 false 4 4.781,1.042 4.896,1.219 0.115,0.177 10 false 5 2.76,1.396 3.146,1.583 0.385,0.188 10 false A35 2.75,1.552 3.146,1.729 0.396,0.177 10 false Diode 2.979,1.979 3.156,2.125 0.177,0.146 10 false 5 3.74,2.354 3.885,2.531 0.146,0.177 10 false 1 3.74,1.979 3.885,2.156 0.146,0.177 10 false 3 2.99,2.375 3.156,2.531 0.167,0.156 10 false 2 4.167,1.052 4.281,1.208 0.115,0.156 10 false B 4.615,1.031 4.729,1.188 0.115,0.156 10 false L 2.656,1.052 2.802,1.229 0.146,0.177 10 false 1 3.146,1.052 3.292,1.229 0.146,0.177 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

NG

2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Disconnect the Park/Neutral Position (PNP) switch connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


f.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

Result
Starter Signal Proceed to
Remains ON A
OFF B



A

3.INSPECT ECM (STA TERMINAL VOLTAGE)

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Disconnect the PNP switch connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition Proceed to
A24-46 (STA) - Body ground Ignition switch ON Below 1.5 V A
11 to 14 V B




A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PNP SWITCH - ST RELAY)

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
A107908E97
2.604,2.51 2.208,1.979 false 0.771,1.063 1.219,1.563 false 1.688,1.542 2.406,0.917 false 2.677,2.479 3.052,2.708 0.375,0.229 10 false L (-) 0.375,0.906 0.781,1.104 0.406,0.198 10 false B (+) 0.115,0.094 2.583,0.469 2.469,0.375 10 false Component without harness connected: (PNP Switch) 2.438,0.792 3,1.031 0.563,0.24 10 false RB (+)

a.

Disconnect the PNP switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Except P or N 10 kΩ or higher
2 (RB) - 5 (L) All positions 10 kΩ or higher


Result
Result Proceed to
Short between 4 and 5 A
Short between 2 and 5 B
Within standard range C



A

5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.INSPECT IGNITION SWITCH ASSEMBLY
5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT

6.INSPECT IGNITION SWITCH ASSEMBLY
6.INSPECT IGNITION SWITCH ASSEMBLY
B110407E06
0.072,0.049 2.589,0.427 2.517,0.378 10 Component without harness connected: (Ignition Switch) 2.827,1.071 3.076,1.227 0.248,0.156 10 IG1 2.048,1.048 2.361,1.208 0.313,0.161 10 ACC 0.261,1.054 0.579,1.219 0.318,0.165 10 AM1 0.785,2.721 1.085,2.877 0.299,0.156 10 ST2 2.655,2.772 2.987,2.937 0.332,0.165 10 AM2 2.13,2.849 2.402,3.015 0.272,0.165 10 IG2 2.776,1.162 2.1,1.867 false 2.008,1.134 1.687,1.775 false 1.057,1.816 0.65,1.145 false 1.802,2.188 2.222,2.826 false 2.1,2.154 2.618,2.844 false 1.381,2.188 0.929,2.704 false

a.

Disconnect the ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 7 (ST2) Ignition switch position not START 10 kΩ or higher
Ignition switch position START Below 1 Ω




OK

7.READ VALUE USING TECHSTREAM (STARTER SIGNAL)

NG

REPLACE IGNITION SWITCH ASSEMBLY

7.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON


Result
Result Proceed to
NG A
OK B



A

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)

B

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)

NEXT

9.CHECK WHETHER DTC OUTPUT RECURS
9.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.

Result
Result Proceed to
P0617 is output A
No DTC is output B



A

B

END