Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

HINT:

Refer to DTC P2120 (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P2120).


DTC No. DTC Detection Condition Trouble Area
P2121 Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic):

(1) Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)

(2) Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM



MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.

MONITOR STRATEGY

Related DTCs P2121: Accelerator pedal position sensor rationality
Required Sensors/Components (Main) Accelerator pedal sensor assembly
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

ALL (Case 1 and Case 2)
Monitor runs whenever following DTCs not stored P2120, P2122, P2123, P2125, P2127, P2128, P2138 (Accelerator pedal position sensor)
Either of following conditions 1 or 2 met: -
1. Ignition switch ON
2. Throttle actuator power ON

Case 2
VPA2 voltage Less than 4.84 V
Either of following conditions met: a or b
a) VPA voltage - Learned VPA accelerator off position voltage 0.04 V or more
b) VPA2 voltage - Learned VPA2 accelerator off position voltage 0.04 V or more

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Difference between VPA voltage and VPA2 voltage (learned value of accelerator off position) Less than 0.4 V, or more than 1.2 V

Case 2
(VPA voltage - Learned VPA accelerator off position voltage) - (VPA2 voltage - Learned VPA2 accelerator off position voltage) 0.165 V or more (varies with accelerator position)

CONFIRMATION DRIVING PATTERN

A256657E01
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.75,0.333 1.625,0.24 10 Accelerator Pedal State 0.896,0.458 1.698,0.708 0.802,0.25 10 Depressed 0.99,0.927 1.708,1.167 0.719,0.24 10 Released 0.427,2.406 1.667,2.667 1.24,0.26 10 Ignition Switch ON 2.115,2.49 2.333,2.75 0.219,0.26 10 [A] 4.396,3.406 4.646,3.635 0.25,0.229 10 [C] 5.313,1.729 6.063,1.979 0.75,0.25 10 Released 2.375,3.052 3.167,3.333 0.792,0.281 10 5 seconds 2.99,1.219 3.823,1.469 0.833,0.25 10 Depressed 3.865,3.042 4.083,3.25 0.219,0.208 10 [B] 2.594,2.031 3.25,2.25 0.656,0.219 10 Released

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream ON.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Wait for 5 seconds after turning the ignition switch to ON.

7.

Operate the accelerator pedal in accordance with the following procedure [B].

1.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt %, and Accel Sens. No.2 Volt %.

2.

Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, and then slowly release the accelerator pedal.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2121.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. The ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode.

If the either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

This DTC relates to the Accelerator Pedal Position (APP) sensor.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P2121 is output A
P2121 and other DTCs are output B

HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITIONSENSOR)

B

2.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITIONSENSOR)
FI07052E62
0.385,1.771 1.125,1.969 0.74,0.198 10 false Depressed 2.365,1.771 3.01,1.969 0.646,0.198 10 false Released

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the values displayed on the Techstream.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 4.7 V




OK

NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.

Result
Result Proceed to
P2121 is output A
No DTC is output B



A

B

END