The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | H1-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 2 | F1-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 3 | H2-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 4 | F2-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 5 | H3-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 6 | F3-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 7 | H4-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 8 | F4-2 - Ground | Ignition switch ON | 11 to 14 V |
OK
NG
Inspect the fuel injector assembly (See page Engine / Hybrid System>1UR-FE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | H1-1 - Ground | Always | 10 kΩ or higher |
| H1-1 - D74-86 (#10) | Always | Below 1 Ω | |
| No. 2 | F1-1 - Ground | Always | 10 kΩ or higher |
| F1-1 - D74-109 (#20) | Always | Below 1 Ω | |
| No. 3 | H2-1 - Ground | Always | 10 kΩ or higher |
| H2-1 - D74-85 (#30) | Always | Below 1 Ω | |
| No. 4 | F2-1 - Ground | Always | 10 kΩ or higher |
| F2-1 - D74-108 (#40) | Always | Below 1 Ω | |
| No. 5 | H3-1 - Ground | Always | 10 kΩ or higher |
| H3-1 - D74-84 (#50) | Always | Below 1 Ω | |
| No. 6 | F3-1 - Ground | Always | 10 kΩ or higher |
| F3-1 - D74-107 (#60) | Always | Below 1 Ω | |
| No. 7 | H4-1 - Ground | Always | 10 kΩ or higher |
| H4-1 - D74-83 (#70) | Always | Below 1 Ω | |
| No. 8 | F4-1 - Ground | Always | 10 kΩ or higher |
| F4-1 - D74-106 (#80) | Always | Below 1 Ω |
OK
NG
Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INJ fuse | Always | Below 1 Ω |
| IG2 MAIN fuse | Always | Below 1 Ω |
OK
NG
Inspect the integration relay (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>IGNITION RELAY NO. 2>ON-VEHICLE INSPECTION).
OK
NG