Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  Cranking Holding Function Circuit  


DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.

When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the park/neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal.

Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.

A169043E07
3.198,4.563 2.719,4.677 false 4.688,4.104 4.906,3.802 false 0.25,1.125 1.5,1.521 1.25,0.396 10 false Starter Input Signal (STSW) 0.24,2.063 1.594,2.469 1.354,0.406 10 false Starter Output Signal (STAR) 0.25,3.031 1.635,3.625 1.385,0.594 10 false ACC (Accessory) Cut Input Signal (ACCR) (for start control) 0.25,4.354 1.594,4.719 1.344,0.365 10 false Engine Speed Signal (NE) 2.021,0.99 2.323,1.188 0.302,0.198 10 false ON 1.979,1.417 2.385,1.635 0.406,0.219 10 false OFF 2.021,1.885 2.323,2.083 0.302,0.198 10 false ON 1.979,2.313 2.385,2.531 0.406,0.219 10 false OFF 1.844,3.542 2.5,3.792 0.656,0.25 10 false ACC Cut 1.99,4.688 4.125,4.917 2.135,0.229 10 false Ignition Switch ST Position 2.927,5.073 3.802,5.302 0.875,0.229 10 false Elapsed Time 4.875,0.469 6.865,0.99 1.99,0.521 10 false Continues cranking until the engine is judged to have started successfully 4.917,1.75 6.844,2.115 1.927,0.365 10 false When no cranking hold control is performed 4.865,2.802 6.917,3.167 2.052,0.365 10 false Prevents meters, clock, etc. from flickering 4.927,3.573 6.927,3.99 2,0.417 10 false Threshold indicating that engine has started 4.677,4.25 6.625,4.969 1.948,0.719 10 false When the NE signal reaches a predetermined value, the ECM determines that the engine has started successfully 1.844,3.083 2.667,3.302 0.823,0.219 10 false No ACC Cut

WIRING DIAGRAM

A185042E08
2.719,1.656 3.021,1.813 0.302,0.156 10 false A45 3.5,1.656 3.792,1.833 0.292,0.177 10 false D73 5.948,1.281 6.365,1.479 0.417,0.198 10 false NSW 5.948,0.854 6.385,1.063 0.438,0.208 10 false STAR 5.948,0.385 6.417,0.552 0.469,0.167 10 false STSW 5.948,1.76 6.313,1.927 0.365,0.167 10 false STA 5.604,1.656 5.917,1.833 0.313,0.177 10 false A24 3.5,0.865 3.802,1.021 0.302,0.156 10 false D73 3.5,1.26 3.833,1.448 0.333,0.188 10 false D73 5.604,1.26 5.917,1.427 0.313,0.167 10 false D74 5.594,0.865 5.906,1.031 0.313,0.167 10 false D74 5.604,0.396 5.906,0.573 0.302,0.177 10 false A24 5.615,1.073 5.885,1.219 0.271,0.146 10 false 120 5.646,1.469 5.833,1.615 0.188,0.146 10 false 46 5.646,0.208 5.833,0.354 0.188,0.146 10 false 14 5.646,0.667 5.833,0.813 0.188,0.146 10 false 16 4.917,1.552 5.021,1.698 0.104,0.146 10 false 5 4.167,1.552 4.271,1.698 0.104,0.146 10 false 4 4.177,1.938 4.469,2.094 0.292,0.156 10 false D35 4.177,2.073 5.156,2.417 0.979,0.344 10 false Park/Neutral Position Switch 2.198,1.875 2.531,2.052 0.333,0.177 10 false A35 2.198,2.021 2.635,2.208 0.438,0.188 10 false Diode 1.854,1.542 1.969,1.688 0.115,0.146 10 false 7 0.604,1.542 0.719,1.688 0.115,0.146 10 false 5 1.51,1.74 1.823,1.917 0.313,0.177 10 false ST2 1.208,3.583 1.479,3.75 0.271,0.167 10 false ST 3.333,3.271 3.563,3.427 0.229,0.156 10 false ST 0.74,1.75 1.104,1.927 0.365,0.177 10 false AM2 0.479,2.865 0.833,3.031 0.354,0.167 10 false AM2 3.74,2.5 3.844,2.646 0.104,0.146 10 false 3 3.01,2.5 3.115,2.646 0.104,0.146 10 false 5 3,2.885 3.104,3.031 0.104,0.146 10 false 2 3.74,2.885 3.844,3.031 0.104,0.146 10 false 1 4.188,5.292 4.302,5.448 0.115,0.156 10 false 1 3.646,5.313 3.76,5.469 0.115,0.156 10 false 1 3.917,5.292 4.125,5.438 0.208,0.146 10 false E3 3.604,5.479 3.833,5.625 0.229,0.146 10 false E5 3.708,5.927 4.167,6.083 0.458,0.156 10 false Starter 6.313,4.677 6.656,4.833 0.344,0.156 10 false ECM 1.385,6.042 1.865,6.208 0.479,0.167 10 false Battery 0.802,2.344 1.74,2.5 0.938,0.156 10 false Ignition Switch 0.802,2.219 1.083,2.385 0.281,0.167 10 false J9 2.698,1.875 3.948,2.052 1.25,0.177 10 false Junction Connector 2.802,1.469 2.906,1.615 0.104,0.146 10 false 7 3.583,1.469 3.688,1.615 0.104,0.146 10 false 5 3.594,1.073 3.698,1.219 0.104,0.146 10 false 6 3.594,0.688 3.698,0.833 0.104,0.146 10 false 7 4.76,1.552 4.865,1.698 0.104,0.146 10 false L 4.313,1.552 4.438,1.698 0.125,0.146 10 false B 2.104,1.573 2.208,1.719 0.104,0.146 10 false 1 2.573,1.573 2.677,1.719 0.104,0.146 10 false 2

PROCEDURE

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the result when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Condition Starter Signal
ON OFF
START ON




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ECM (STSW TERMINAL VOLTAGE)
2.INSPECT ECM (STSW TERMINAL VOLTAGE)
U151526E02
1.854,1.667 2.646,1.354 false 0.219,1.771 0.552,1.948 0.333,0.177 10 false A24 2.708,1.24 3.219,1.448 0.51,0.208 10 false STSW 0.198,0.125 2.5,0.49 2.302,0.365 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the ECM connector.


b.

Perform the cranking operation.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Ignition Switch Condition Specified Condition
A24-14 (STSW) - Body ground ON Below 1 V
START 9 to 13 V



HINT:

DTCs related to the communication with other computers may be set due to this inspection. Clear those DTCs after the inspection.



OK

3.INSPECT ECM (STAR TERMINAL OUTPUT VOLTAGE)

NG

7.INSPECT IGNITION SWITCH ASSEMBLY
3.INSPECT ECM (STAR TERMINAL OUTPUT VOLTAGE)
A379713E01
1.719,0.802 2.115,1.031 0.396,0.229 0.51,0.052 2.823,0.438 2.313,0.385 10 false Rear view of wire harness connector: (to Junction Connector) 1.781,0.833 2.167,1.01 0.385,0.177 10 false D73 3.521,0.073 5.99,0.313 2.469,0.24 10 false Engine Room Connector Holder Block

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the All Cylinders Fuel Cut.


e.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
D73-6 (Junction Connector) - Body ground Ignition switch ON (shift lever in P or N) Below 1 V
Ignition switch ON (shift lever not in P or N) 9 to 13 V
Cranking operation 9 to 13 V


HINT:
·

The junction connector is in the engine room connector holder block as shown in the illustration.

·

During this inspection, all connectors and relays should be connected.




OK

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH ASSEMBLY - ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH ASSEMBLY - ECM)
A379710E01
5.021,0.865 5.448,1.115 0.427,0.25 1.833,0.833 2.26,1.083 0.427,0.25 2.24,1.417 2.49,2.229 true 1.885,1.885 1.615,2.271 true 5.688,1.583 6.146,1.354 true 0.448,0.104 2.781,0.479 2.333,0.375 10 false Front view of wire harness connector: (to ECM) 4.167,0.083 6.5,0.458 2.333,0.375 10 false Front view of wire harness connector: (to PNP Switch) 2.469,2.26 3.083,2.458 0.615,0.198 10 false STAR 1.354,2.292 1.771,2.479 0.417,0.188 10 false NSW 1.917,0.875 2.24,1.073 0.323,0.198 10 false D74 5.104,0.917 5.427,1.115 0.323,0.198 10 false D35 6.208,1.25 6.438,1.448 0.229,0.198 10 false B

a.

Disconnect the park/neutral position (PNP) switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D35-4 (B) - D74-16 (STAR) Always Below 1 Ω
D35-4 (B) - D74-120 (NSW) Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
A379711E01
1.156,1.01 1.583,1.24 0.427,0.229 3.375,0.948 3.802,1.177 0.427,0.229 3.823,1.917 3.313,2.313 true 1.073,1.854 0.729,2.125 true 0.083,0.073 2.406,0.427 2.323,0.354 10 false Front view of wire harness connector: (to PNP Switch) 2.49,0.073 4.813,0.427 2.323,0.354 10 false Front view of wire harness connector:(to ECM) 4.927,0.083 6.729,0.26 1.802,0.177 10 false Engine Room Relay Block: 1.229,1.052 1.583,1.229 0.354,0.177 10 false D35 3.469,0.979 3.823,1.156 0.354,0.177 10 false A24 5.813,0.802 6.104,0.979 0.292,0.177 10 false ST 2.979,2.292 3.333,2.469 0.354,0.177 10 false STA 0.615,2.115 0.906,2.292 0.292,0.177 10 false L

a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the park/neutral position (PNP) switch assembly switch connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D35-5 (L) - A24-46 (STA) Always Below 1 Ω
D35-5 (L) - ST relay (1) Always Below 1 Ω
ST relay (2) - Body ground Always Below 1 Ω




OK

REPAIR OR REPLACE STARTER CIRCUIT (STARTER - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1UR-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY AND ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY AND ECM)
A379712E01
1.094,1.219 1.438,1.469 0.344,0.25 0.625,2.927 1.01,3.156 0.385,0.229 4.927,0.708 5.344,0.958 0.417,0.25 2.156,1.385 2.74,1.146 true 2.479,2.948 3.063,2.708 true 5.313,1.271 5.979,2.135 true 4.958,1.75 4.656,2.156 true 0.573,0.094 2.896,0.458 2.323,0.365 10 false Front view of wire harness connector: (to Ignition Switch) 0.635,1.76 2.958,2.125 2.323,0.365 10 false Front view of wire harness connector: (to PNP Switch) 3.979,0.063 6.302,0.427 2.323,0.365 10 false Front view of wire harness connector: (to ECM) 2.802,1.031 3.26,1.229 0.458,0.198 10 false ST2 1.198,1.26 1.448,1.438 0.25,0.177 10 false J9 3.125,2.615 3.344,2.844 0.219,0.229 10 false B 0.698,2.958 1.021,3.156 0.323,0.198 10 false D35 5.01,0.75 5.333,0.948 0.323,0.198 10 false D74 5.958,2.177 6.417,2.375 0.458,0.198 10 false STAR 4.427,2.188 4.885,2.385 0.458,0.198 10 false NSW

a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the Park/Neutral Position (PNP) switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
J9-7 (ST2) - D35-4 (B) Always Below 1 Ω
D74-16 (STAR) - D35-4 (B) Always
D74-120 (NSW) - D35-4 (B) Always
J9-7 (ST2) or D35-4 (B) - Body ground Always 10 kΩ or higher
D74-16 (STAR) or D35-4 (B) - Body ground Always
D74-120 (NSW) or D35-4 (B) - Body ground Always


HINT:

The wire between the PNP switch and ignition switch has a diode (refer to the wiring diagram). The current flowing to the PNP switch is rectified by the diode.




OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
A379711E01
1.156,1.01 1.583,1.24 0.427,0.229 3.375,0.948 3.802,1.177 0.427,0.229 3.823,1.917 3.313,2.313 true 1.073,1.854 0.729,2.125 true 0.083,0.073 2.406,0.427 2.323,0.354 10 false Front view of wire harness connector: (to PNP Switch) 2.49,0.073 4.813,0.427 2.323,0.354 10 false Front view of wire harness connector:(to ECM) 4.927,0.083 6.729,0.26 1.802,0.177 10 false Engine Room Relay Block: 1.229,1.052 1.583,1.229 0.354,0.177 10 false D35 3.469,0.979 3.823,1.156 0.354,0.177 10 false A24 5.813,0.802 6.104,0.979 0.292,0.177 10 false ST 2.979,2.292 3.333,2.469 0.354,0.177 10 false STA 0.615,2.115 0.906,2.292 0.292,0.177 10 false L

a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the Park/Neutral Position (PNP) switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D35-5 (L) or A24-46 (STA) - Body ground Always 10 kΩ or higher
D35-5 (L) or ST relay (1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR