Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM U

1UR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, use the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer.
Engine Speed Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
650 to 800 rpm: Idling -
Calculate Load Calculated load by ECM/
Min.: 0%, Max.: 100%
·

11 to 25%: Idling

·

12 to 26%: Driving without load (2500 rpm)


-
Vehicle Load Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load -
MAF Air flow rate from Mass Air Flow (MAF) meter/
Min.: 0 gm/sec., Max.: 655.35 gm/sec.
3.4 to 6.2 gm/sec.: Idling If value approximately 0.0 gm/sec.:
·

Mass air flow meter power source circuit open or shorted.

·

VG circuit open or shorted.


If value 160.0 gm/sec. or more:
·

E2G circuit open.


Atmosphere Pressure Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure) -
MAP Intake manifold pressure/
Min.: 0 kPa, Max.: 255 kPa
·

80 to 110 kPa: Ignition switch ON

·

28 to 48 kPa: Idling


-
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.: 215°C
80 to 100°C (176 to 212°F): After warming up If value -40°C (-40°F), sensor circuit open.
If value 140°C (284°F), sensor circuit shorted.
Intake Air Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature If value -40°C (-40°F), sensor circuit open.
If value 140°C (284°F), sensor circuit shorted.
Engine Run Time Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start Service data
Initial Engine Coolant Temp Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
Engine coolant temperature when engine started Service data
Initial Intake Air Temp Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
Intake air temperature when engine started Service data
Battery Voltage Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling -
Accelerator Position Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position -
Accel Sens. No.1 Volt % Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal is released
52 to 90%: Accelerator pedal is fully depressed
-
Accel Sens. No.2 Volt % Absolute APP No. 2/
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal is released
68 to 95%: Accelerator pedal is fully depressed
-
Accel Sensor Out No.1 APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal is released
2.6 to 4.5 V: Accelerator pedal is fully depressed
-
Accel Sensor Out No.2 APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal is released
3.4 to 4.75 V: Accelerator pedal is fully depressed
-
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling -
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1/
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2/
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data
Throttle Sensor Volt % Absolute throttle position sensor/
Min.: 0%, Max.: 100%
·

10 to 22%: Throttle fully closed

·

64 to 96%: Throttle fully open


The calculated value based on VTA1.
Throttl Sensor #2 Volt % Throttle sensor position #2/
Min.: 0%, Max.: 100%
·

42 to 62%: Throttle fully closed

·

92 to 100%: Throttle fully open


The calculated value based on VTA2.
ST1 Brake pedal signal/
ON or OFF
ON: Brake pedal depressed -
System Guard System guard/
ON or OFF
- ETCS service data
Open Side Malfunction Open side malfunction/
ON or OFF
- ETCS service data
Throttle Idle Position Whether or not throttle position sensor detecting idle/
ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Throttle Require Position Throttle requirement position/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling -
Throttle Sensor Position* Throttle sensor position/
Min.: 0%, Max.: 100%
·

0%: Throttle fully closed

·

50 to 80%: Throttle fully open


Recognition value of throttle opening angle for ECM
Throttle Position No. 1 Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal released

·

4.6 to 5.0 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value/
Min.: 0 V, Max.: 4.98 V
0.5 to 4.8 V -
Throttle Sens Open Pos #1 Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V ETCS service data
Throttle Sens Open Pos #2 Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V ETCS service data
Throttle Motor Current Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling ETCS service data
Throttle Motor DUTY Throttle actuator/
Min.: 0%, Max.: 100%
10 to 22%: Idling ETCS service data
Throttle Motor Duty (Open) Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling ETCS service data
Throttle Motor Duty (Close) Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling ETCS service data
Throttle Fully Close Learn Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal released -
+BM Voltage +BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal ETCS service data
Actuator Power Supply Actuator power supply/
ON or OFF
ON: Idling ETCS service data
Throttle Position Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
- For use when engine stall, starting problems or rough idle is present.
ISC Flow Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
- For use when engine stall, starting problems or rough idle is present.
ISC Position Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
- For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
ISC Learning Value ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
PS Feedback Val Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Low Revolution Control Low engine speed control operation state/
ON or OFF
- For use when engine stall, starting problems or rough idle is present.
N Range Status Shift lever N status/
ON or OFF
- For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
- For use when engine stall, starting problems or rough idle is present.
Fuel Pump Duty Fuel pump duty/
Min.: 0%, Max.: 399.0%
- -
Injector (Port) Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1400 to 4000 μs: Idling -
Injection Volum (Cylinder 1) Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml Quantity of fuel injection volume for 10 times
Vacuum Pump Key-off EVAP system pump status/
ON or OFF
- -
Current Fuel Type Status of the current fuel type Gasoline/petrol -
EVAP (Purge) VSV Purge VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling Order signal from ECM
Evap Purge Flow Purge flow/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling -
Purge Density Learn Value Learning value of purge density/
Min.: -200, Max.: 199.993
Idling: -40 to 0 Service data
Vapor Pressure Pump Vapor pressure/
Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg)
Approximately 100 kPa (750 mmHg): Ignition switch ON EVAP system pressure monitored by canister pressure sensor.
Vapor pressure (Calculated) Calculated EVAP system pressure/
Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg)
Approximately 100 kPa (750 mmHg): Ignition switch ON -
EVAP System Vent Valve Key-off EVAP system vent valve status/
ON or OFF
- -
EVAP Purge VSV VSV status for EVAP control/
ON or OFF
- -
Purge Cut VSV Duty Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
- -
Target Air-Fuel Ratio Target Air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling -
AF Lambda B1S1 Output air fuel ratio associated with the Bank 1 Sensor 1/
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value greater than 1 (1.001 to 1.999) = Lean


-
AF Lambda B2S1 Output air fuel ratio associated with the Bank 2 Sensor 1/
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value greater than 1 (1.001 to 1.999) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
AFS Voltage B2S1 Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
AFS Current B1S1 Air fuel ratio sensor current (for Bank 1 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor.
AFS Current B2S1 Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor.
A/F Heater Duty #1 A/F heater duty ratio (for Bank 1)
Min.: 0%, Max.: 399.9%
0 to 100% -
A/F Heater Duty #2 A/F heater duty ratio (for Bank 2)
Min.: 0%, Max.: 399.9%
0 to 100% -
O2S B1S2 Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
O2S B2S2 Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
O2S Impedance B1S2 Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm After driving approx. 10 min. in urban area
O2S Impedance B2S2 Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm After driving approx. 10 min. in urban area
O2 Heater B1S2 Heated oxygen sensor heater (for Bank 1 Sensor 2)/
Active or Not Act
- -
O2 Heater B2S2 Heated oxygen sensor heater (for Bank 2 Sensor 2)/
Active or Not Act
- -
O2 Heater Curr Val B1S2 Heated oxygen sensor current (for Bank 1 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
- -
O2 Heater Curr Val B2S2 Heated oxygen sensor current (for Bank 2 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
- -
Short FT #1 Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1 Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20%
·

This item refers to the overall fuel compensation carried out in long-term to compensate for a continual deviation of the short-term fuel trim from the central value.

·

Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.


A/F Learn Value Idle #1 Air fuel ratio learned value for idling (for Bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #1 Air fuel ratio learned value for low engine loads (for Bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1 Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1 Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1 Air fuel ratio learned value for high engine loads (for Bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #1 Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling -
Short FT #2 Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2 Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to +20%
·

This item refers to the overall fuel compensation carried out in long-term to compensate for a continual deviation of the short-term fuel trim from the central value.

·

Air-fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.


A/F Learn Value Idle #2 Air fuel ratio learned value for idling (for Bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #2 Air fuel ratio learned value for low engine loads (for Bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #2 Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #2 Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #2 Air fuel ratio learned value for high engine loads (for Bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #2 Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling -
Fuel System Status #1 Fuel system status (Bank 1)/
OL, CL, OL Drive, OL Fault or CL Fault
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using A/F sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to detected system fault.

·

CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.


Fuel System Status #2 Fuel system status (Bank 2)/
OL, CL, OL Drive, OL Fault or CL Fault
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using A/F sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to detected system fault.

·

CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.


Air pump pressure (Absolute) Air pump pressure (absolute) for Bank 1/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open
Close to atmospheric pressure: Air pump OFF, air switching valve closed
Refer to DTC P2431
(See page (Click here))
Air Pump2 Pressure (Absolute) Air pump pressure (absolute) for Bank 2/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open
Close to atmospheric pressure: Air pump OFF, air switching valve closed
Refer to DTC P2431
(See page (Click here))
Air Pump Pulsation Pressure Air pump pulsation pressure for Bank 1/
Min.: 0 kPa, Max.: 655.35 kPa
- Cumulative pulsation pressure calculated by ECM
(See page (Click here))
Air Pump2 Pulsation Pressure Air pump pulsation pressure for Bank 2/
Min.: 0 kPa, Max.: 655.35 kPa
- Cumulative pulsation pressure calculated by ECM
(See page (Click here))
Secondary Air Control VSV Secondary air injection system status/
ON or OFF
ON: Secondary air injection system operating -
2nd Air System Status Secondary air system status/
ON or OFF
ON: Secondary air system operating -
AI Test AI operation prohibition/
READY or NOT RDY
READY -
Subfreezing Conditions Subfreezing conditions status/
ON or OFF
- -
Air Pump Heater Air pump heater status/
ON or OFF
- -
IGN Advance Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC 5 to 15°: Idling -
Knock Feedback Value Feedback value of knocking/
Min.: -1024 deg (CA), Max.: 1023.9 deg (CA)
-22 to 0 deg (CA):
Driving at 70 km/h (44 mph)
Service data
Knock Correct Learn Value Correction learning value of knocking/
Min.: -1024 deg (CA), Max.: 1023.9 deg (CA)
0 to 25 deg (CA):
Driving at 70 km/h (44 mph)
Service data
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #7 Individual cylinder timing advance compensation amount (No. 7)/
Min.: 0° CA, Max.: 15.93° CA
- For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #8 Individual cylinder timing advance compensation amount (No. 8)/
Min.: 0 deg (CA), Max.: 15.93 deg (CA)
- For use when engine stall, starting problems or rough idle is present.
ACIS VSV VSV status for ACIS control/
ON or OFF
- Active Test support data
Target EGR Position EGR valve target opening amount/
Min.: 0%, Max.: 100%
Changes according to engine speed and load: Driving -
EGR Step Position EGR step position/
Min.: 0 step, Max.: 255 step
Changes according to engine speed and load: Driving
0 step: Shift lever in D after racing the engine with shift lever in N
-
VVT Control Status #1 Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
- -
VVT Control Status #2 VVT control status (Bank 2)/
ON or OFF
- -
VVT Advance Fail VVT control failure status/
ON or OFF
ON: VVT control failure -
VVT Aim Angle #1*2 VVT target duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0%: Idling VVT duty signal value during forced operation.
VVT Change Angle #1*2 VVT change angle (Bank 1)/
Min.: 0 degFR, Max.: 639.9 degFR
0 to 5 degFR: Idling Displacement angle during forced operation.
VVT OCV Duty #1*2 VVT OCV operation duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0%: Idling Requested duty value for forced operation.
VVT Aim Angle #2*2 VVT target duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0%: Idling VVT duty signal value during forced operation.
VVT Change Angle #2*2 VVT change angle (Bank 2)/
Min.: 0 degFR, Max.: 639.9 degFR
0 to 5 degFR: Idling Displacement angle during forced operation.
VVT OCV Duty #2*2 VVT OCV operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0%: Idling Requested duty value for forced operation.
VVT Ex Hold Lrn Val #1*2 VVT exhaust hold duty ratio learning value (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 80%: Idling -
VVT Ex Chg Angle #1*2 VVT exhaust change angle (Bank 1)/
Min.: 0 degFR, Max.: 639.9 degFR
0 to 40 degFR: Idling Displacement angle during forced operation.
VVT Ex OCV Duty #1*2 VVT exhaust OCV duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling Requested duty value for forced operation.
VVT Ex Hold Lrn Val #2*2 VVT exhaust hold duty ratio learning value (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 80%: Idling -
VVT Ex Chg Angle #2*2 VVT exhaust change angle (Bank 2)/
Min.: 0 degFR, Max.: 639.9 degFR
0 to 40 degFR: Idling Displacement angle during forced operation.
VVT Ex OCV Duty #2*2 VVT exhaust OCV duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling Requested duty value for forced operation.
VN Turbo Type VN turbo type/
Not Avl, Commo, Vacuum or CAN Com
Not Avl -
Catalyst Temp B1S1 Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B2S1 Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B1S2 Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
- -
Catalyst Temp B2S2 Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
- -
Starter Signal Starter signal/
ON or OFF
ON: Cranking -
Starter Control Starter switch status/
Open or Close
Open: Cranking -
Power Steering Signal Power steering switch signal/ ON or OFF ON: Power steering operating -
Starter Relay Starter relay status/
ON or OFF
ON: Cranking -
ACC Relay ACC relay status/
ON or OFF
ON: Cranking -
Neutral Position SW Signal PNP switch status/
ON or OFF
ON: P or N position -
Transfer L4 L4 status of the transfer/
ON or OFF
ON: 4WD control switch in 4L position -
Stop Light Switch Stop light switch/
ON or OFF
ON: Brake pedal is depressed -
A/C Signal A/C switch status/
ON or OFF
ON: A/C ON -
Closed Throttle Position SW Closed throttle position switch/
ON or OFF
·

ON: Throttle fully closed

·

OFF: Throttle open


-
Fuel Cut Condition Fuel cut condition/
ON or OFF
ON: Fuel cut operating -
Immobiliser Communication Immobiliser communication/
ON or OFF
ON: Normal -
Check Mode Check mode/
ON or OFF
ON: Check mode ON Refer to Check Mode Procedure (See page (Click here)).
SPD Test Result Check mode result for vehicle speed sensor/
Compl or Incmpl
- -
AS Test Result Check mode result for secondary air injection system/
Compl or Incmpl
- -
Misfire Test Result Check mode result for misfire monitor/
Compl or Incmpl
- -
OXS1 Test Result Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
- -
OXS2 Test Result Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
- -
A/F Test Results #2 Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
- -
A/F Test Results #1 Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
- -
Complete Parts Monitor Comprehensive component monitor/
Not Avl or Avail
- -
Fuel System Monitor Fuel system monitor/
Not Avl or Avail
- -
Misfire Monitor Misfire monitor/
Not Avl or Avail
- -
EGR/VVT Monitor EGR/VVT monitor/
Not Avl or Avail
- -
EGR/VVT Monitor EGR/VVT monitor/
Compl or Incmpl
- -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor/
Not Avl or Avail
- -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor/
Compl or Incmpl
- -
O2S(A/FS) Monitor O2S (A/FS) monitor/
Not Avl or Avail
- -
O2S(A/FS) Monitor O2S (A/FS) monitor/
Compl or Incmpl
- -
A/C Monitor A/C monitor/
Not Avl or Avail
- -
A/C Monitor A/C monitor/
Compl or Incmpl
- -
2nd Air Monitor 2nd air monitor/
Not Avl or Avail
- -
2nd Air Monitor 2nd air monitor/
Compl or Incmpl
- -
EVAP Monitor EVAP monitor/
Not Avl or Avail
- -
EVAP Monitor EVAP monitor/
Compl or Incmpl
- -
Heated Catalyst Monitor Heated catalyst monitor/
Not Avl or Avail
- -
Heated Catalyst Monitor Heated catalyst monitor/
Compl or Incmpl
- -
Catalyst Monitor Catalyst monitor/
Not Avl or Avail
- -
Catalyst Monitor Catalyst monitor/
Compl or Incmpl
- -
Component Monitor ENA Comprehensive component monitor/
Unable or Enable
- -
Component Monitor CMPL Comprehensive component monitor/
Compl or Incmpl
- -
Fuel System Monitor ENA Fuel system monitor/
Unable or Enable
- -
Fuel System Monitor CMPL Fuel system monitor/
Compl or Incmpl
- -
Misfire Monitor ENA Misfire monitor/
Unable or Enable
- -
Misfire Monitor CMPL Misfire monitor/
Compl or Incmpl
- -
EGR/VVT Monitor ENA EGR monitor/
Unable or Enable
- -
EGR/VVT Monitor CMPL EGR monitor/
Compl or Incmpl
- -
Heater Monitor ENA O2S (A/FS) heater monitor/
Unable or Enable
- -
Heater Monitor CMPL O2S (A/FS) heater monitor/
Compl or Incmpl
- -
O2S(A/FS) Monitor ENA O2S (A/FS) monitor/
Unable or Enable
- -
O2S(A/FS) Monitor CMPL O2S (A/FS) monitor/
Compl or Incmpl
- -
A/C Monitor ENA A/C monitor/
Unable or Enable
- -
A/C Monitor CMPL A/C monitor/
Compl or Incmpl
- -
2nd Air Monitor ENA 2nd air monitor/
Unable or Enable
- -
2nd Air Monitor CMPL 2nd air monitor/
Compl or Incmpl
- -
EVAP Monitor ENA EVAP monitor/
Unable or Enable
- -
EVAP Monitor CMPL EVAP monitor/
Compl or Incmpl
- -
Heated Cat Monitor ENA Heated catalyst monitor/
Unable or Enable
- -
Heated Cat Monitor CMPL Heated catalyst monitor/
Compl or Incmpl
- -
Catalyst Monitor ENA Catalyst monitor/
Unable or Enable
- -
Catalyst Monitor CMPL Catalyst monitor/
Compl or Incmpl
- -
TC Terminal TC terminal status/
ON or OFF
- -
# Codes (Include History) Number of codes/
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status/
ON or OFF
ON: MIL ON -
MIL ON Run Distance MIL ON run distance/
Min.: 0 km, Max.: 65535 km
Distance after DTC detected -
Running Time from MIL ON Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned ON -
Time after DTC Cleared Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs were cleared -
Distance from DTC Cleared Distance after DTCs cleared/
Min.: 0 km, Max.: 65535 km
Driving distance after DTCs were cleared -
Warmup Cycle Cleared DTC Warm-up cycles after DTCs cleared/
Min.: 0, Max.: 255
- Number of warm-up cycles after DTCs cleared
Dist Batt Cable Disconnect Distance after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected -
IG OFF Elapsed Time Time after ignition switch off/
Min.: 0 min, Max.: 655350 min
Cumulative time after ignition switch off -
OBD Requirements OBD requirement OBD II (California ARB) -
Number of Emission DTC Emission related DTCs - Number of emission related DTCs
TC and TE1 TC and CG (TE1) terminals of DLC3/
ON or OFF
- -
Total Distance Traveled Total distance traveled/
Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile)
- -
Ignition Trig. Count Ignition counter/
Min.: 0, Max.: 65535
0 to 800 -
Cylinder #1 Misfire Count
to
Cylinder #8 Misfire Count
Misfire count of cylinder 1 to 8/
Min.: 0, Max.: 255
0 This item displayed only when idling engine.
All Cylinders Misfire Count All cylinders misfire count/
Min.: 0, Max.: 255
0 to 35 -
Multi Cylinders Misfire Count Multiple cylinder misfire count/
Min.: 0, Max.: 65535
0 to 65535 -
Misfire RPM Engine RPM for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0 -
Misfire Load Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0 -
Misfire Margin Misfire monitoring/
Min.: -128%, Max.: 127%
-100 to 99.2% Misfire detection margin
Catalyst OT MF F/C Catalyst over temperature misfire prevention F/C/
Not Avl or Avail
Avail: Cat OT MF F/C available
Not Avl: Cat OT MF F/C not available
-
Cat OT MF F/C History Catalyst over temperature misfire prevention F/C history/
ON or OFF
ON: Fuel cut operation history exists -
Cat OT MF F/C Cylinder #1 Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #2 Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #3 Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #4 Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #5 Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #6 Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #7 Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Cat OT MF F/C Cylinder #8 Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut is operating -
Engine Speed (Starter Off) Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
- For use when engine stall, starting problems or rough idle is present.
Starter Count Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
- For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
- Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time Time elapsed after engine started (interval between ignition switch ON and off)/
Min.: 0 ms, Max.: 655350 ms
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
- For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation History of hesitation during engine start/
ON or OFF
- -
Low Rev for Eng Start History of low engine speed after engine start/
ON or OFF
- -
Minimum Engine Speed Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
- For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure Power steering oil pressure/
Min.: 0 MPa, Max.: 25.599 MPa
- -
ACT VSV A/C cut status for Active Test/
ON or OFF
- Active Test support data
Brake Override System Brake Override System Status/
ON or OFF
ON: Brake override system operation -
Electric Cooling Fan Low Electric fan motor operation status/
ON or OFF
ON: Cooling fan operated at low speed -
Idle Fuel Cut Fuel cut at idle/
ON or OFF
ON: Fuel cut operating Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm.
FC TAU Fuel cut TAU: Fuel cut during very light load/
ON or OFF
ON: Fuel cut operating The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut Status of the immobiliser fuel cut/
ON or OFF
- -
Immobiliser Fuel Cut History Status of the immobiliser fuel cut history/
ON or OFF
- -
Vehicle Spec Signal 1 Status of the Vehicle Spec Judge Signal 1/
OFF or ON
- -
Electrical Load Signal 1 Electrical load signal/
ON or OFF
- -
Electrical Load Signal 2 Electrical load signal/
ON or OFF
- -
Cruise Cancel Signal Status of the cruise cancel signal/
ON or OFF
- -
Model Code Model code - Used for identifying the model code:
UPK5##
Engine Type Engine type - Used for identifying the engine type:
1URFE
Cylinder Number Number of cylinders/
Min.: 0, Max.: 255
- Used for identifying number of cylinders:
8
Transmission Type Transmission type - Used for identifying the transmission type:
ECT 6th
Transmission Type 2 Transmission type2 NA -
Destination Destination - Used for identifying the destination:
A (America)
Model Year Model year/
Min.: 1900, Max.: 2155
- Used for identifying the model year:
20##
System Identification System Identification System identification - Identifying the engine system: Gasoline (gasoline engine).
Engine Speed of Cyl #1 Engine RPM for cylinder No. 1/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #2 Engine RPM for cylinder No. 2/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #3 Engine RPM for cylinder No. 3/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #4 Engine RPM for cylinder No. 4/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #5 Engine RPM for cylinder No. 5/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #6 Engine RPM for cylinder No. 6/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #7 Engine RPM for cylinder No. 7/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #8 Engine RPM for cylinder No. 8/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
Av Engine Speed of All Cyl Engine RPM for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression is performed using Active Test.
A/F Sensor Determination (worst value) #1 Worst judgment value of air fuel ratio sensor output (bank 1)/
Min.: -1, Max.: 0.99
0.00 -
A/F Sensor Determination (worst value) #2 Worst judgment value of air fuel ratio sensor output (bank 2)/
Min.: -1, Max.: 0.99
0.00 -
Engine Speed Fluctuation Avg (worst value) #1 Worst value of average engine speed fluctuation (cylinder No. 1)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #2 Worst value of average engine speed fluctuation (cylinder No. 2)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #3 Worst value of average engine speed fluctuation (cylinder No. 3)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #4 Worst value of average engine speed fluctuation (cylinder No. 4)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #5 Worst value of average engine speed fluctuation (cylinder No. 5)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #6 Worst value of average engine speed fluctuation (cylinder No. 6)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #7 Worst value of average engine speed fluctuation (cylinder No. 7)/
Min.: 0, Max.: 2.55
0.00 -
Engine Speed Fluctuation Avg (worst value) #8 Worst value of average engine speed fluctuation (cylinder No. 8)/
Min.: 0, Max.: 2.55
0.00 -
SPD (NT) Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
Lock-up is:
·

ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) -
Overdrive Cut Switch #1 Overdrive cut signal for cruise control/
ON or OFF
- -
Shift SW Status (P Range) Park/Neutral Position switch status (P Range)/
ON or OFF
Shift lever is:
·

In P: ON

·

Not in P: OFF


When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect
Shift SW Status (R Range) Park/Neutral Position switch status (R Range)/
ON or OFF
Shift lever is:
·

In R: ON

·

Not in R: OFF


When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect
Shift SW Status (N Range) Park/Neutral Position switch status (N Range)/
ON or OFF
Shift lever is:
·

In N: ON

·

Not in N: OFF


When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect
Shift SW Status (N,P Range) Supported Status of park/neutral position switch (N or P) supported/
Unsupp or Supp
- -
Shift SW Status (N,P Range) Park/Neutral Position switch status/
ON or OFF
Shift lever is:
·

In N or P: ON

·

Not in N or P: OFF


When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
Shift lever is:
·

ON: In S, "+" or "-"

·

OFF: Not in S, "+" or "-"


-
Shift SW Status (D Range) Park/Neutral Position switch status (D Range)/
ON or OFF
Shift lever is:
·

In D, S, "+" or "-": ON

·

Not in D, S, "+" or "-": OFF


When shift lever position displayed on Techstream differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C, Max.: 215°C
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature while engine is cold


If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted
A/T Oil Temperature 2 No. 2 ATF temperature sensor value/
Min.: -40°C, Max.: 215°C
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature while engine is cold


If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted
Lock Up Lock-up/
ON or OFF
Lock-up is:
·

Operating: ON

·

Not operating: OFF


-
Shift Status ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever is:
·

In D: 1st, 2nd, 3rd, 4th, 5th or 6th

·

In S: 1st, 2nd, 3rd, 4th, 5th or 6th


-
SLT Solenoid Status Shift solenoid SLT status/
ON or OFF
Shift solenoid SLT is:
·

Accelerator pedal is depressed: OFF

·

Accelerator pedal is released: ON


-
SLU Solenoid Status Shift solenoid SLU status/
ON or OFF
Shift solenoid SLU is:
·

Operating: ON

·

Not operating: OFF


-



HINT:
·

*1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).

·

*2: Data List values are only displayed when performing the following Active test: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active test, the Data List value will be 0.

·

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be OFF, and all accessory switches should be OFF.



ACTIVE TEST


HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.

Tester Display Test Part Control Range Diagnostic Note
Control the Injection Volume Change injection volume Between -12.5% and 24.8%
·

All injectors tested at the same time.

·

Perform test at or below 3000 rpm.

·

Injection volume can be changed in 1% gradations within control range.


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

Perform test at or below 3000 rpm.

·

Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor voltage outputs.

·

To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2SB2 S2.


Control the EGR Step Position Open or close EGR valve 0 to 110 steps
·

EGR valve is fully closed at step position 0, and fully open at step position 110.

·

Amount of EGR gas flowing into the intake manifold varies in accordance with the EGR valve opening angle.

·

Perform this test when the following conditions are met:

·

Vehicle is stopped.

·

Engine is running.


·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.


Activate the VSV for Secondary Air Control Activate the Secondary Air Injection System ON/OFF
·

Do not perform test for 5 seconds or more.

·

After test, do not perform test again for 30 seconds.


Activate the VSV for Intake Control Activate VSV for ACIS ON/OFF -
Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
Control the A/C Cut Signal Control A/C cut signal ON/OFF -
Control the Fuel Pump / Speed Activate fuel pump ON/OFF This test is possible when the following conditions are met:
·

Ignition switch ON.

·

Engine not started.

·

Shift lever in P.


Control the Fuel Pump Duty Activate fuel pump 25%/80% This test is possible when the following conditions are met:
·

Ignition switch ON.

·

Engine is running.

·

Shift lever in P.


Connect the TC and TE1 Turn on and off TC and CG (TE1) connection ON/OFF
·

ON: TC and CG (TE1) connected.

·

OFF: TC and CG (TE1) disconnected.


Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
Prohibit the Catalyst OT Misfire prevent F/C Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire ON: Fuel cut is prohibited Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
Activate the Starter Relay Activate the starter relay ON/OFF Perform this test with the engine stopped.
Activate the ACC Cut Relay Activate the ACC CUT relay ON/OFF Perform this test with the engine stopped.
Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open
Open: Throttle valve opens slowly
This test is possible when the following conditions are met:
·

Ignition switch ON.


·

Engine not started.


·

Fully depressing accelerator pedal (APP: 58 degrees or more).

·

Shift lever in P.


Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open
Open: Throttle valve opens quickly
Same as above.
Control the VVT Linear (Bank 1) Control Variable Valve Timing (VVT) [Bank 1] -128 to 127% (This value added to present OCV control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stall or rough idle when VVT actuator operated by 100%.

·

Test possible during idle.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank 1) Turn Oil Control Valve (OCV) on and off ON/OFF
·

Engine stalls or idles roughly when OCV turned ON.

·

Normal engine running or idling when OCV OFF.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Linear (Bank 2) Control Variable Valve Timing (VVT) [Bank 2] -128 to 127% (This value added to present OCV control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stall or rough idle when VVT actuator operated by 100%.

·

Test possible during idle.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank 2) Turn Oil Control Valve (OCV) on and off ON/OFF
·

Engine stalls or idles roughly when OCV turned ON.

·

Normal engine running or idling when OCV OFF.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Exhaust Linear (Bank 1) Control VVT (Bank 1) -128 to 127% (This value added to present OCV control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stall or rough idle when VVT actuator operated by 100%.

·

Test possible while engine idling.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Exhaust Linear (Bank 2) Control VVT (Bank 2) -128 to 127% (This value added to present OCV control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stall or rough idle when VVT actuator operated by 100%.

·

Test possible while engine idling.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Activate the Vacuum Pump Activate leak detection pump (built into canister pump module) ON/OFF -
Activate the VSV for Vent Valve Activate vent valve (built into canister pump module) ON/OFF -
Activate the Air Pump Heater Activate air pump heater ON/OFF
·

This test activates the air pump heater for up to 60 seconds.

·

To protect the air pump heater, do not perform this test more than 4 times in a row.


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #8) injection fuel cut #1/#2/#3/#4/#5/#6/#7/#8
ON/OFF
Test possible while vehicle stopped and engine idling*1.
Control the All Cylinders Fuel Cut All cylinder fuel cut ON/OFF Test possible while vehicle stopped and engine idling*1.
Check the Cylinder Compression*2 Check the cylinder compression pressure ON/OFF Fuel injection and ignition stop in all cylinders.

NOTICE:
*1:
·

If the display of the Data List's Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.

·

If the display of the Data List's Catalyst OT MF F/C item is Avail, perform this Active Test as described below.

1.

Stop the engine, turn the ignition switch ON.

2.

Enter the Control the Select Cylinder Fuel Cut.

3.

Select the cylinder for fuel cut (cylinder #1 to #8) and turn the Active Test ON (press the RIGHT or LEFT button).

4.

Start the engine.




HINT:

*2: When cranking the engine, each cylinder measures the engine speed.

In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

6.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


9.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


10.

Monitor the engine speed (Engine Speed of Cyl #1 to #8) displayed on the Techstream.

HINT:

At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.

·

Use a fully-charged battery.



11.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


12.

Push the snapshot button to turn the snapshot function off.

13.

Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

HINT:

If the data is not displayed as a graph, the change of the values cannot be observed.


14.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.





SYSTEM CHECK


HINT:

Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility.


e.

Perform the System Check by referring to the table below.

Tester Display Test Part Control Range Diagnostic Note
Evaporative System Check
(Automatic Mode)
Perform 6 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
·

If no DTCs in Pending menu after performing this test, system functioning normally.

·

Refer to EVAP Inspection Procedure (See page (Click here)).


Evaporative System Check
(Manual Mode)
Perform 6 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
·

Used to detect malfunctioning parts.

·

Refer to EVAP Inspection Procedure (See page (Click here)).


Secondary Air Injection Check
(Automatic Mode)
Perform secondary air injection system operation automatically With warm engine, ignition switch turned off once
·

If no DTCs in Pending menu after performing this test, system functioning normally.

·

Refer to inspection procedure for secondary air injection system DTCs.

·

When performing Secondary Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.

·

Turn ignition switch off when System Check finished.


Secondary Air Injection Check
(Manual Mode)
Perform 7 operations in order to operate air injection system monitor manually With warm engine, ignition switch turned off once
·

Used to detect malfunctioning parts.

·

Refer to inspection procedure for secondary air injection system DTCs.

·

When performing Secondary Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.

·

Turn ignition switch off when System Check finishes.