Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  P2437  Open in Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  P2438  Short in Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  


DESCRIPTION

The Secondary Air Injection (AIR) system consists of an air pump, the Air Switching Valve (ASV), a pressure sensor, the Air Injection Control Driver (AID) and the ECM. For a short time after a cold engine start, the AIR system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the ASV.

The AID drives the ASV and the air pump according to command signals transmitted by the ECM. The pressure sensor detects the pressure in the secondary air passage when the AIR system is ON and OFF, and transmits a pressure signal to the ECM.

The AID is not only equipped to drive the pump and valve, but also has a diagnosis function to detect malfunctions in the AIR system circuit.

HINT:

As a large current is required to drive the air pump and ASV, an AID is installed to this system.


A211725E02
1.021,1.938 0.729,2.521 false 4.594,0.594 4.073,1.25 false 3.292,3.219 3.531,2.594 true 2.594,2.625 2.75,2.063 false 3.542,2.417 4.26,3.573 true 5.594,1.563 5.344,1.823 false 4.073,2.073 4.802,1.146 true 2.177,1.688 3.313,0.198 true 1.604,0.677 1.958,0.844 0.354,0.167 10 false ECM 3.365,0.125 5.385,0.333 2.021,0.208 10 false Air Injection Control Driver (AID) 0.458,2.51 1.635,2.708 1.177,0.198 10 false Diagnostic Signal 4.646,0.521 5.698,0.708 1.052,0.188 10 false Pressure Signal 3.052,3.24 3.823,3.417 0.771,0.177 10 false Reed Valve 2.042,2.583 3.156,2.771 1.115,0.188 10 false ASV Drive Signal 3.781,3.583 5,3.948 1.219,0.365 10 false Air Switching Valve (ASV) 5.646,3.51 6.26,3.708 0.615,0.198 10 false Air Pump 6.198,2.083 6.563,2.271 0.365,0.188 10 false Filter 5.646,1.469 7.073,1.667 1.427,0.198 10 false Air Pump Drive Signal 4.854,0.99 5.979,1.198 1.125,0.208 10 false Pressure Sensor

DTC No. DTC Detection Condition Trouble Area
P2431
P2436
Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
·

Pressure sensor (Air switching valve assembly)

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
·

Pressure sensor (Air switching valve assembly)

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
·

Pressure sensor (Air switching valve assembly)

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E34
0.177,2.76 1.531,2.948 1.354,0.188 10 false Air Switching Valve 2.594,2.927 2.917,3.104 0.323,0.177 10 false ECM 2.292,0.865 2.698,1.031 0.406,0.167 10 false VCV1 2.292,1.5 2.573,1.677 0.281,0.177 10 false AIP 0.885,1.635 1.125,1.813 0.24,0.177 10 false AIP 2.313,2.146 2.552,2.313 0.24,0.167 10 false E2 0.885,0.99 1.135,1.177 0.25,0.188 10 false VC 0.906,2.281 1.135,2.458 0.229,0.177 10 false E2 0.104,0.115 2.177,0.344 2.073,0.229 10 false Reference (for Bank 1):

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

MONITOR STRATEGY

Related DTCs P2431: Air flow/Pressure sensor circuit rationality
P2432: Air flow/Pressure sensor circuit range check (Low voltage)
P2433: Air flow/Pressure sensor circuit range check (High voltage)
P2436: Air flow/Pressure sensor circuit rationality
P2437: Air flow/Pressure sensor circuit range check (Low voltage)
P2438: Air flow/Pressure sensor circuit range check (High voltage)
Required Sensors/Components (Main) Pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration P2432, P2433, P2437, P2438: 0.5 seconds
P2431, P2436: 5 seconds
MIL Operation P2432, P2433, P2437, P2438: Immediate
P2431, P2436: 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P2431 and P2436
Monitor runs whenever following DTCs not present P2432, P2433, P2437, P2438 (AIR pressure sensor - Low/High)
Starter OFF
Battery voltage 8 V or more
Ignition switch ON

P2432, P2433, P2437 and P2438
Monitor runs whenever following DTCs not present None
Starter OFF
Battery voltage 8 V or more
Ignition switch ON

TYPICAL MALFUNCTION THRESHOLDS

P2431 and P2436
Air pressure Less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg)

P2432 and P2437
Air pressure sensor voltage Less than 0.5 V

P2433 and P2438
Air pressure sensor voltage More than 4.5 V

COMPONENT OPERATING RANGE

Air pressure sensor voltage Between 0.5 V and 4.5 V

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - ECM)
A379593E01
0.438,0.833 0.844,1.063 0.406,0.229 1.26,0.833 1.667,1.063 0.406,0.229 3.198,0.792 3.604,1.021 0.406,0.229 5.865,0.76 6.271,0.99 0.406,0.229 1.031,1.635 0.646,2.021 true 1.177,1.635 1.302,2.031 true 1.323,1.635 1.729,2.021 true 2.792,1.677 2.74,2.177 true 3.354,1.75 3.531,2.167 true 6,1.823 5.917,2.208 true 6.073,1.823 6.49,2.167 true 0.042,0.052 2.375,0.417 2.333,0.365 10 false Front view of wire harness connector: (to Air Switching Valve) 2.417,0.073 4.75,0.438 2.333,0.365 10 false Front view of wire harness connector: (to to ECM) 4.802,0.073 7.135,0.438 2.333,0.365 10 false Front view of wire harness connector: (to to ECM) 0.521,0.865 0.844,1.042 0.323,0.177 10 false D58 1.344,0.865 1.708,1.052 0.365,0.188 10 false D59 0.885,0.854 1.115,1.052 0.229,0.198 10 false *1 1.719,0.844 1.948,1.042 0.229,0.198 10 false *2 0.292,2.01 0.708,2.208 0.417,0.198 10 false VC*1 0.281,2.167 0.813,2.365 0.531,0.198 10 false VC2*2 0.104,2.417 1.052,2.604 0.948,0.188 10 false *1: for Bank 1 1.146,2.052 1.563,2.25 0.417,0.198 10 false AIP*1 1.135,2.188 1.688,2.354 0.552,0.167 10 false AIP2*2 1.729,2.021 2.146,2.219 0.417,0.198 10 false E2*1 1.729,2.177 2.177,2.365 0.448,0.188 10 false E22*2 1.354,2.427 2.302,2.615 0.948,0.188 10 false *2: for Bank 2 5.938,0.781 6.302,0.969 0.365,0.188 10 false A24 2.615,2.198 3.031,2.396 0.417,0.198 10 false VCV1 3.531,2.188 3.833,2.365 0.302,0.177 10 false E2 3.281,0.823 3.646,1.01 0.365,0.188 10 false D74 5.698,2.24 6.115,2.438 0.417,0.198 10 false AIP2 6.448,2.198 6.865,2.396 0.417,0.198 10 false AIP

a.

Disconnect the air switching valve connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D58-3 (AIP) - A24-54 (AIP) Always Below 1 Ω
D58-2 (VC) - D74-67 (VCV1) Always Below 1 Ω
D58-4 (E2) - D74-98 (E2) Always Below 1 Ω
D59-3 (AIP2) - A24-53 (AIP2) Always Below 1 Ω
D59-2 (VC2) - D74-67 (VCV1) Always Below 1 Ω
D59-4 (E22) - D74-98 (E2) Always Below 1 Ω
D58-3 (AIP) or A24-54 (AIP) - Body ground Always 10 kΩ or higher
D58-2 (VC) or D74-67 (VCV1) - Body ground Always 10 kΩ or higher
D59-3 (AIP2) or A24-53 (AIP2) - Body ground Always 10 kΩ or higher
D59-2 (VC2) or D74-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check the pressure displayed on the Techstream.

Standard pressure:

45 to 135 kPa


HINT:

The Techstream displays the air pump pressure as absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

B

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)

C

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)