Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0403  Exhaust Gas Recirculation Control Circuit  


DESCRIPTION

Refer to DTC P0401 (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0401).

DTC No. DTC Detection Condition Trouble Area
P0403 Open or short in EGR valve circuit
(1 trip detection logic)
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM



HINT:

DTC P0403 is set when the ignition switch is in the ON position.


MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.

If the EGR terminal voltage is low when the EGR terminal output is off, the ECM determines that the EGR valve circuit is malfunctioning.

MONITOR STRATEGY

Related DTCs P0403: Exhaust gas recirculation control circuit range check
Required Sensors/Components (Main) EGR valve
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 1 second
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Engine Running
Battery voltage 10.5 V or higher
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition 1, 2, 3 or 4
1: Both conditions are met: Condition A and B
A: Motor phase 1 output terminal voltage Low
B: Either condition is met: -
Motor Driving
Motor phase 1 Not operating
2: Both conditions are met: Condition A and B
A: Motor phase 2 output terminal voltage Low
B: Either condition is met: -
Motor Driving
Motor phase 2 Not operating
3: Both conditions are met: Condition A and B
A: Motor phase 3 output terminal voltage Low
B: Either condition is met: -
Motor Driving
Motor phase 3 Not operating
4: Both conditions are met: Condition A and B
A: Motor phase 4 output terminal voltage Low
B: Either condition is met: -
Motor Driving
Motor phase 4 Not operating

CONFIRMATION DRIVING PATTERN

A215251E02
2.329,2.896 2.916,3.225 0.586,0.330 10 Warming Up 3.406,2.896 4.119,3.085 0.714,0.190 10 10 minutes 2.025,2.046 2.223,2.234 0.198,0.188 10 [A] 2.532,1.777 2.757,1.966 0.225,0.189 10 [B] 3.781,0.69 3.993,0.877 0.211,0.187 10 [C] 4.44,3.293 4.678,3.463 0.238,0.171 10 [D] 0.113,0.809 1.797,1.024 1.684,0.215 10 20 km/h (12 mph) or more 1.435,1.902 1.808,2.074 0.373,0.172 10 Idling 0.609,2.207 1.818,2.404 1.209,0.197 10 Ignition Switch ON

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on [A].

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Start the engine and warm it up [B].

5.

Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


6.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

7.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



8.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

9.

Input the DTC: P0403.

10.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


11.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.

Inspect the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>INSPECTION).


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



OK

3.INSPECT EGR VALVE ASSEMBLY (+B OR +B2 VOLTAGE)

NG

3.INSPECT EGR VALVE ASSEMBLY (+B OR +B2 VOLTAGE)
U151685E01
0.067,0.048 2.416,0.395 2.349,0.347 10 Front view of wire harness connector: (to EGR Valve) 0.427,1.763 0.725,1.919 0.298,0.156 10 D85 2.435,1.279 2.730,1.435 0.295,0.156 10 +B2 2.386,2.365 2.681,2.521 0.295,0.156 10 +B1 2.386,1.371 1.785,1.697 false 1.779,2.104 2.337,2.456 false

a.

Disconnect the EGR valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
D85-5 (+B1) - Body ground Ignition switch ON 11 to 14 V
D85-2 (+B2) - Body ground Ignition switch ON 11 to 14 V


c.

Reconnect the EGR valve assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EGR VALVE ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
A379430E01
0.521,1.521 0.948,1.781 0.427,0.26 4.76,0.875 5.188,1.135 0.427,0.26 2.063,1.625 2.542,1.24 true 1.604,1.896 1.292,2.208 true 1.135,1.146 1.635,1.573 true 2.021,1.896 2.531,2.198 true 3.802,2.208 4.115,1.521 true 4.25,2.427 4.115,1.594 true 4.917,2.333 4.115,1.448 true 4.5,2.219 4.188,1.594 true 0.719,0.094 3.031,0.469 2.313,0.375 10 false Front view of wire harness connector: (to EGR Valve) 4,0.094 6.313,0.469 2.313,0.375 10 false Front view of wire harness connector: (to ECM) 2.604,1.115 3.219,1.313 0.615,0.198 10 false EGR2 0.719,1.01 1.188,1.219 0.469,0.208 10 false EGR4 2.563,2.188 3.177,2.385 0.615,0.198 10 false EGR3 1.01,2.25 1.479,2.469 0.469,0.219 10 false EGR1 3.552,2.229 4.021,2.438 0.469,0.208 10 false EGR3 4.104,2.438 4.573,2.646 0.469,0.208 10 false EGR4 4.375,2.24 4.844,2.458 0.469,0.219 10 false EGR1 4.865,2.354 5.479,2.552 0.615,0.198 10 false EGR2 0.604,1.583 0.958,1.792 0.354,0.208 10 false D85 4.844,0.927 5.198,1.135 0.354,0.208 10 false D74

a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D74-48 (EGR1) - D85-4 (EGR1) Always Below 1 Ω
D74-1 (EGR2) - D85-3 (EGR2) Always Below 1 Ω
D74-24 (EGR3) - D85-6 (EGR3) Always Below 1 Ω
D74-47 (EGR4) - D85-1 (EGR4) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D74-48 (EGR1) or D85-4 (EGR1) - Body ground Always 10 kΩ or higher
D74-1 (EGR2) or D85-3 (EGR2) - Body ground Always 10 kΩ or higher
D74-24 (EGR3) or D85-6 (EGR3) - Body ground Always 10 kΩ or higher
D74-47 (EGR4) or D85-1 (EGR4) - Body ground Always 10 kΩ or higher


d.

Reconnect the EGR valve assembly connector.


e.

Reconnect the ECM connector.



OK

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0403)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0403)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


e.

Confirm that no DTC is set using the Techstream.


Result
Result Proceed to
DTC P0403 output A
No DTC output B


A

B

END

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EGR VALVE ASSEMBLY)
A379433E01
0.583,1.563 1,1.823 0.417,0.26 3.958,1.104 4.323,1.354 0.365,0.25 4.896,1.104 5.26,1.354 0.365,0.25 5.563,1.104 5.927,1.354 0.365,0.25 1.854,1.604 2.479,1.198 false 1.854,1.938 2.604,2.219 false 5.031,1.802 4.74,2.208 false 0.708,0.104 3.01,0.5 2.302,0.396 10 false Front view of wire harness connector: (to EGR Valve) 3.823,0.083 6.135,0.479 2.313,0.396 10 false Front view of wire harness connector: (to Integration Relay) 0.656,1.615 0.979,1.813 0.323,0.198 10 false D85 2.552,1.083 3.01,1.281 0.458,0.198 10 false +B2 2.656,2.135 3.115,2.333 0.458,0.198 10 false +B1 4.042,1.146 4.365,1.344 0.323,0.198 10 false 1A 4.979,1.146 5.302,1.344 0.323,0.198 10 false 1B 5.656,1.167 5.979,1.365 0.323,0.198 10 false 1C 4.677,2.24 4.875,2.438 0.198,0.198 10 false 4

a.

Disconnect the EGR valve assembly connector.


b.

Remove the integration relay from engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
1B-4 - D85-5 (+B1) Always Below 1 Ω
1B-4 - D85-2 (+B2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
1B-4 or D85-5 (+B1) - Body ground Always 10 kΩ or higher
1B-4 or D85-2 (+B2) - Body ground Always 10 kΩ or higher


d.

Reconnect the EGR valve assembly connector.


e.

Reinstall the integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR