Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A379702E01
4.354,1.031 6.25,1.219 1.896,0.188 10 false 5 V Constant Voltage Circuit 5.365,1.875 6.385,2.063 1.021,0.188 10 false Microprocessor 2.917,0.865 3.385,1.063 0.469,0.198 10 false BATT 3,1.208 3.302,1.406 0.302,0.198 10 false +B 3.135,2.146 3.438,2.344 0.302,0.198 10 false VC 4.958,3.229 5.427,3.427 0.469,0.198 10 false ECM 4.073,3.01 4.271,3.208 0.198,0.198 10 false R 1.24,0.99 2.573,1.208 1.333,0.219 10 false from EFI NO. 1 Fuse 1.573,1.313 2.573,1.521 1,0.208 10 false from EFI Relay 0.208,1.906 2.667,2.438 2.458,0.531 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.188,2.854 2.635,3.385 2.448,0.531 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A217955E02
5.322,0.509 5.595,0.650 0.273,0.141 10 D74 5.322,0.932 5.595,1.073 0.273,0.141 10 D74 5.322,1.343 5.595,1.485 0.273,0.141 10 D74 5.322,2.059 5.595,2.200 0.273,0.141 10 D74 5.322,2.472 5.595,2.613 0.273,0.141 10 D74 5.322,3.183 5.595,3.324 0.273,0.141 10 D74 5.322,3.591 5.595,3.732 0.273,0.141 10 D74 5.322,4.3 5.595,4.441 0.273,0.141 10 D74 5.322,4.71 5.595,4.852 0.273,0.141 10 D74 5.322,5.432 5.595,5.574 0.273,0.141 10 D74 5.324,5.852 5.597,5.993 0.273,0.141 10 D74 5.324,6.585 5.597,6.726 0.273,0.141 10 D74 5.319,7 5.593,7.141 0.273,0.141 10 D74 5.375,6.827 5.549,6.972 0.174,0.144 10 65 5.374,6.407 5.550,6.546 0.176,0.139 10 64 5.677,7.007 6.010,7.154 0.333,0.147 10 EV2- 5.319,7.751 5.593,7.893 0.273,0.141 10 D74 5.375,7.579 5.549,7.723 0.174,0.144 10 97 5.677,7.759 6.010,7.905 0.333,0.147 10 PIM 5.677,6.582 6.041,6.729 0.364,0.147 10 EV2+ 5.677,5.851 6.039,5.991 0.362,0.140 10 VV2- 5.677,5.44 6.039,5.579 0.362,0.140 10 VV2+ 5.375,5.253 5.548,5.396 0.173,0.142 10 87 5.375,5.68 5.548,5.822 0.173,0.141 10 88 5.372,4.109 5.552,4.251 0.180,0.142 10 69 5.374,4.542 5.550,4.684 0.176,0.142 10 68 5.374,3.419 5.549,3.561 0.175,0.142 10 91 5.374,3.003 5.549,3.145 0.175,0.142 10 92 5.372,1.886 5.552,2.032 0.180,0.147 10 90 5.373,2.292 5.551,2.436 0.178,0.143 10 89 5.336,1.172 5.587,1.316 0.251,0.144 10 111 5.335,0.766 5.588,0.908 0.253,0.142 10 110 5.371,0.343 5.552,0.487 0.181,0.144 10 66 5.677,0.418 6.078,0.573 0.401,0.155 10 VCV2 5.677,0.942 5.978,1.089 0.301,0.146 10 NE+ 5.677,1.342 5.978,1.488 0.301,0.146 10 NE- 5.677,2.062 5.891,2.206 0.214,0.144 10 G2 5.677,2.476 5.932,2.628 0.254,0.152 10 G2- 5.677,3.189 6.045,3.343 0.368,0.154 10 VV1+ 5.677,3.593 6.045,3.747 0.368,0.154 10 VV1- 5.677,4.291 6.046,4.441 0.369,0.150 10 EV1+ 5.677,4.723 6.017,4.869 0.339,0.146 10 EV1- 2.923,0.418 3.034,0.566 0.111,0.147 10 3 2.923,0.84 3.039,0.984 0.116,0.144 10 1 2.923,1.251 3.044,1.400 0.121,0.149 10 2 2.923,1.765 3.034,1.912 0.111,0.147 10 3 2.923,1.976 3.039,2.120 0.116,0.144 10 1 2.923,2.387 3.044,2.536 0.121,0.149 10 2 2.923,2.886 3.034,3.033 0.111,0.147 10 3 2.923,3.097 3.039,3.241 0.116,0.144 10 1 2.923,3.508 3.044,3.657 0.121,0.149 10 2 2.923,4.012 3.034,4.159 0.111,0.147 10 3 2.923,4.223 3.039,4.367 0.116,0.144 10 1 2.923,4.634 3.044,4.783 0.121,0.149 10 2 2.923,5.141 3.034,5.288 0.111,0.147 10 3 2.923,5.352 3.039,5.496 0.116,0.144 10 1 2.923,5.764 3.044,5.913 0.121,0.149 10 2 2.923,6.293 3.034,6.441 0.111,0.147 10 3 2.923,6.505 3.039,6.649 0.116,0.144 10 1 2.923,6.916 3.044,7.065 0.121,0.149 10 2 2.596,0.52 2.811,0.661 0.214,0.141 10 VC 2.505,0.933 2.810,1.073 0.305,0.141 10 NE+ 2.544,1.351 2.810,1.494 0.266,0.144 10 NE- 2.596,1.854 2.811,1.995 0.214,0.141 10 VC 2.607,2.063 2.811,2.204 0.204,0.141 10 G2 2.637,2.473 2.811,2.617 0.174,0.144 10 G- 2.596,2.98 2.811,3.120 0.214,0.141 10 VC 2.438,3.189 2.809,3.330 0.371,0.141 10 VVL+ 2.48,3.599 2.810,3.743 0.329,0.144 10 VVL- 2.512,4.094 2.810,4.234 0.297,0.141 10 VC2 2.522,4.315 2.810,4.456 0.288,0.141 10 EX+ 2.552,4.724 2.810,4.865 0.258,0.141 10 EX- 2.596,5.235 2.811,5.376 0.214,0.141 10 VC 2.418,5.445 2.809,5.586 0.391,0.141 10 VVR+ 2.449,5.855 2.809,5.999 0.360,0.144 10 VVR- 2.512,6.372 2.810,6.513 0.297,0.141 10 VC2 2.522,6.594 2.810,6.734 0.288,0.141 10 EX+ 2.552,7.003 2.810,7.143 0.258,0.141 10 EX- 6.134,8.253 6.470,8.406 0.335,0.152 10 ECM 0.233,0.508 0.437,0.656 0.205,0.149 10 D3 0.233,0.662 1.958,0.818 1.725,0.156 10 Crankshaft Position Sensor 0.233,1.839 0.437,1.987 0.205,0.149 10 D6 0.233,1.993 1.958,2.149 1.725,0.156 10 Camshaft Position Sensor 0.233,2.966 0.528,3.115 0.295,0.149 10 D37 0.233,3.12 2.000,3.436 1.767,0.316 10 VVT Sensor (for Intake Side of Bank 1) 0.233,4.08 0.528,4.229 0.295,0.149 10 D40 0.233,4.234 2.104,4.550 1.871,0.316 10 VVT Sensor (for Exhaust Side of Bank 1) 0.233,5.22 0.528,5.369 0.295,0.149 10 D39 0.233,5.374 2.000,5.689 1.767,0.316 10 VVT Sensor (for Intake Side of Bank 2) 0.233,6.359 0.528,6.508 0.295,0.149 10 D41 0.233,6.513 2.104,6.829 1.871,0.316 10 VVT Sensor (for Exhaust Side of Bank 2) 2.923,7.449 3.034,7.597 0.111,0.147 10 3 2.923,7.66 3.039,7.805 0.116,0.144 10 1 2.923,8.072 3.044,8.221 0.121,0.149 10 2 2.599,7.528 2.822,7.669 0.224,0.141 10 VC 2.534,7.749 2.822,7.890 0.288,0.141 10 PIM 2.631,8.158 2.856,8.331 0.225,0.172 10 E2 0.233,7.515 0.528,7.664 0.295,0.149 10 D80 0.233,7.669 2.451,7.832 2.218,0.163 10 Manifold Absolute Pressure Sensor 4.513,8.504 4.641,8.653 0.128,0.149 10 A

A217956E05
5.656,0.854 6.073,1.01 0.417,0.156 10 false VCV1 5.333,0.948 5.615,1.104 0.281,0.156 10 false D74 5.385,0.802 5.573,0.948 0.188,0.146 10 false 67 5.656,1.313 5.917,1.469 0.26,0.156 10 false AIP 5.333,1.313 5.615,1.469 0.281,0.156 10 false A24 5.01,0.094 5.135,0.25 0.125,0.156 10 false A 5.375,1.156 5.563,1.302 0.188,0.146 10 false 54 5.656,2.427 5.99,2.583 0.333,0.156 10 false AIP2 5.333,2.427 5.646,2.604 0.313,0.177 10 false A24 5.385,2.271 5.594,2.427 0.208,0.156 10 false 53 5.656,2.74 5.896,2.917 0.24,0.177 10 false E2 5.333,2.635 5.646,2.813 0.313,0.177 10 false D74 5.323,3.344 5.625,3.51 0.302,0.167 10 false D74 5.323,4.458 5.615,4.625 0.292,0.167 10 false D74 5.385,2.802 5.594,2.979 0.208,0.177 10 false 98 0.208,0.927 0.51,1.083 0.302,0.156 10 false D58 0.208,1.063 2.188,1.24 1.979,0.177 10 false Air Switching Valve (for Bank 1) 0.208,2.198 0.51,2.354 0.302,0.156 10 false D59 0.208,2.344 2.188,2.521 1.979,0.177 10 false Air Switching Valve (for Bank 2) 2.573,0.958 2.823,1.135 0.25,0.177 10 false VC 2.938,0.865 3.146,1.021 0.208,0.156 10 false 2 2.938,1.219 3.146,1.375 0.208,0.156 10 false 3 2.542,1.302 2.865,1.479 0.323,0.177 10 false AIP 2.594,1.677 2.844,1.854 0.25,0.177 10 false E2 2.927,1.594 3.156,1.76 0.229,0.167 10 false 4 2.5,2.219 2.823,2.375 0.323,0.156 10 false VC2 2.938,2.135 3.146,2.292 0.208,0.156 10 false 2 2.938,2.344 3.146,2.5 0.208,0.156 10 false 3 2.458,2.427 2.833,2.594 0.375,0.167 10 false AIP2 2.521,2.646 2.844,2.813 0.323,0.167 10 false E22 2.927,2.552 3.156,2.719 0.229,0.167 10 false 4 5.656,3.344 6.031,3.542 0.375,0.198 10 false PSP 5.365,3.188 5.615,3.385 0.25,0.198 10 false 72 5.656,4.469 6.115,4.646 0.458,0.177 10 false PPMP 5.333,4.302 5.635,4.469 0.302,0.167 10 false 121 0.219,3.135 0.51,3.292 0.292,0.156 10 false D46 0.219,3.281 1.99,3.635 1.771,0.354 10 false Power Steering Oil Pressure Sensor 2.563,3.146 2.813,3.323 0.25,0.177 10 false VC 2.479,3.354 2.833,3.521 0.354,0.167 10 false PSP 2.583,3.708 2.833,3.875 0.25,0.167 10 false E2 2.917,3.063 3.125,3.219 0.208,0.156 10 false 1 2.906,3.271 3.115,3.427 0.208,0.156 10 false 2 2.906,3.646 3.115,3.802 0.208,0.156 10 false 3 0.208,4.229 0.563,4.396 0.354,0.167 10 false R12 0.208,4.375 1.844,4.552 1.635,0.177 10 false Canister Pressure Sensor 2.479,4.271 2.823,4.427 0.344,0.156 10 false VCC 2.406,4.479 2.833,4.646 0.427,0.167 10 false VOUT 2.385,4.833 2.833,5 0.448,0.167 10 false SGND 2.896,4.188 3.125,4.344 0.229,0.156 10 false 6 2.896,4.396 3.125,4.552 0.229,0.156 10 false 7 2.896,4.76 3.125,4.917 0.229,0.156 10 false 8 6.167,5.469 6.51,5.615 0.344,0.146 10 false ECM

A165789E01
5.214,0.486 5.561,0.641 0.347,0.155 10 ECM 5.385,0.872 5.576,1.027 0.191,0.156 10 80 5.644,0.937 6.043,1.093 0.399,0.156 10 VCTA 5.34,1.023 5.617,1.168 0.277,0.145 10 D74 5.385,1.239 5.576,1.395 0.191,0.156 10 78 5.34,1.391 5.617,1.536 0.277,0.145 10 D74 5.385,1.607 5.576,1.763 0.191,0.156 10 77 5.34,1.758 5.617,1.904 0.277,0.145 10 D74 5.385,1.971 5.576,2.127 0.191,0.156 10 79 5.34,2.122 5.617,2.268 0.277,0.145 10 D74 5.644,1.386 6.026,1.535 0.382,0.149 10 VTA1 5.644,1.754 6.026,1.903 0.382,0.149 10 VTA2 5.644,2.041 5.960,2.190 0.316,0.149 10 ETA 5.389,2.413 5.579,2.558 0.191,0.145 10 57 5.344,2.555 5.618,2.704 0.274,0.149 10 A24 5.389,2.773 5.579,2.919 0.191,0.145 10 59 5.344,2.916 5.618,3.065 0.274,0.149 10 A24 5.389,3.142 5.579,3.288 0.191,0.145 10 55 5.344,3.285 5.618,3.434 0.274,0.149 10 A24 5.389,3.535 5.579,3.680 0.191,0.145 10 56 5.344,3.677 5.618,3.826 0.274,0.149 10 A24 5.389,3.902 5.579,4.047 0.191,0.145 10 58 5.344,4.044 5.618,4.193 0.274,0.149 10 A24 5.389,4.268 5.579,4.414 0.191,0.145 10 60 5.344,4.411 5.618,4.560 0.274,0.149 10 A24 5.644,2.468 6.050,2.624 0.406,0.156 10 VCPA 5.644,3.284 5.957,3.440 0.312,0.156 10 VPA 5.644,3.967 5.957,4.123 0.312,0.156 10 EPA 5.644,3.676 6.019,3.832 0.375,0.156 10 VPA2 5.644,4.331 6.019,4.487 0.375,0.156 10 EPA2 5.644,2.84 6.050,2.996 0.406,0.156 10 VCP2 0.219,1.007 0.444,1.163 0.225,0.156 10 D9 0.219,1.15 1.741,1.306 1.522,0.156 10 Throttle Position Sensor 2.594,1.022 2.828,1.178 0.235,0.156 10 VC 2.521,1.387 2.829,1.541 0.309,0.154 10 VTA 2.453,1.741 2.826,1.906 0.373,0.165 10 VTA2 2.624,2.11 2.840,2.275 0.216,0.165 10 E2 2.904,0.938 3.023,1.094 0.119,0.156 10 5 2.904,1.296 3.023,1.452 0.119,0.156 10 6 2.904,1.662 3.023,1.818 0.119,0.156 10 4 2.904,2.022 3.023,2.178 0.119,0.156 10 3 0.21,2.537 0.500,2.693 0.290,0.156 10 A14 0.21,2.68 1.347,3.012 1.137,0.332 10 Accelerator Pedal Position Sensor 2.433,2.561 2.847,2.711 0.414,0.150 10 VCPA 2.433,2.925 2.847,3.075 0.414,0.150 10 VCP2 2.522,3.285 2.843,3.435 0.321,0.150 10 VPA 2.447,3.682 2.861,3.832 0.414,0.150 10 VPA2 2.527,4.037 2.849,4.187 0.321,0.150 10 EPA 2.452,4.41 2.866,4.560 0.414,0.150 10 EPA2 2.904,2.465 3.023,2.626 0.119,0.161 10 4 2.904,2.825 3.023,2.985 0.119,0.161 10 1 2.904,3.184 3.023,3.345 0.119,0.161 10 6 2.904,3.581 3.023,3.742 0.119,0.161 10 3 2.904,3.957 3.023,4.118 0.119,0.161 10 5 2.904,4.317 3.023,4.477 0.119,0.161 10 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Check the communication between the Techstream and ECM.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



B

3.CHECK MIL (THROTTLE POSITION SENSOR)

A

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B

HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

5.CHECK MIL (CANISTER PUMP MODULE)

A

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (CANISTER PUMP MODULE)
a.

Disconnect the canister pump module connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

6.CHECK MIL (AIR SWITCHING VALVE for Bank 1)

A

6.CHECK MIL (AIR SWITCHING VALVE for Bank 1)
a.

Disconnect the air switching valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

7.CHECK MIL (AIR SWITCHING VALVE for Bank 2)

A

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)

7.CHECK MIL (AIR SWITCHING VALVE for Bank 2)
a.

Disconnect the air switching valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)

A

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the power steering oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

9.CHECK MIL (CAMSHAFT POSITION SENSOR)

A

9.CHECK MIL (CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)

A

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

11.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)

A

11.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)
a.

Disconnect the VVT sensor (for Intake Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

12.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)

A

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1)

12.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)
a.

Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

13.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)

A

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1)

13.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)
a.

Disconnect the VVT sensor (for Intake Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

14.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)

A

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2)

14.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)
a.

Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

15.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

A

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2)

15.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

16.CHECK HARNESS AND CONNECTOR

A

16.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the canister pump module connector.


d.

Disconnect the air switching valve assembly (for Bank 1) connector.


e.

Disconnect the air switching valve assembly (for Bank 2) connector.


f.

Disconnect the power steering oil pressure sensor connector.


g.

Disconnect the camshaft position sensor connector.


h.

Disconnect the crankshaft position sensor connector.


i.

Disconnect the VVT sensor (for Intake Side of Bank 1) connector.


j.

Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.


k.

Disconnect the VVT sensor (for Intake Side of Bank 2) connector.


l.

Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.


m.

Disconnect the manifold absolute pressure sensor connector.


n.

Disconnect the ECM connectors.

A379694E02
1.646,0.927 2.063,1.177 0.417,0.25 5.115,0.875 5.531,1.125 0.417,0.25 2.25,1.844 2.854,2.313 true 5.396,2.302 5.573,1.948 true 1.26,1.844 0.958,2.323 true 1.313,1.854 1.646,2.313 true 5.708,1.958 6.156,2.229 true 0.75,0.104 3.083,0.438 2.333,0.333 10 false Front view of wire harness connector: (to ECM) 1.74,0.969 2.198,1.167 0.458,0.198 10 false D74 2.885,2.271 3.344,2.469 0.458,0.198 10 false VCTA 4.083,0.104 6.417,0.438 2.333,0.333 10 false Front view of wire harness connector: (to ECM) 5.198,0.927 5.656,1.125 0.458,0.198 10 false A24 6.208,2.177 6.667,2.375 0.458,0.198 10 false VCP2 0.76,2.354 1.219,2.552 0.458,0.198 10 false VCV2 1.552,2.344 2.01,2.542 0.458,0.198 10 false VCV1 5.198,2.313 5.656,2.51 0.458,0.198 10 false VCPA


o.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-80 (VCTA) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-59 (VCP2) - Body ground Always 10 kΩ or higher
D74-66 (VCV2) - Body ground Always 10 kΩ or higher
D74-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR