Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1 and EV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
No VVT sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic)
·

Open or short in VVT sensor (for exhaust side of bank 1, 2) circuit

·

VVT sensor (for exhaust side of bank 1, 2)

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM


P0367
P0392
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for exhaust side of bank 1, 2) circuit

·

VVT sensor (for exhaust side of bank 1, 2)

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM


P0368
P0393
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for exhaust side of bank 1, 2) circuit

·

VVT sensor (for exhaust side of bank 1, 2)

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM



A217927E02
0.21,1.18 0.440,1.345 0.230,0.165 10 NE 0.137,1.731 0.441,1.882 0.304,0.151 10 EV1 0.141,2.093 0.440,2.238 0.299,0.145 10 EV2 2.847,1.272 3.184,1.421 0.336,0.149 10 GND 2.847,2.197 3.184,2.346 0.336,0.149 10 GND 2.847,1.824 3.184,1.973 0.336,0.149 10 GND 1.07,2.506 1.991,2.648 0.921,0.141 10 20 msec./DIV. 2.691,0.783 3.254,0.939 0.563,0.156 10 5 V/DIV. 0.061,0.068 2.369,0.246 2.308,0.178 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-110 (NE+) - D74-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-69 (EV1+) - D74-68 (EV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-64 (EV2+) - D74-65 (EV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

EV1 and EV2 are the VVT sensor signals, and NE is the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P0365: VVT position sensor (for Bank 1) verify pulse input
P0367: VVT position sensor (for Bank 1) range check (low voltage)
P0368: VVT position sensor (for Bank 1) range check (high voltage)
P0390: VVT position sensor (for Bank 2) verify pulse input
P0392: VVT position sensor (for Bank 2) range check (low voltage)
P0393: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main) VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration P0365, P0390: 5 seconds
P0367, P0368, P0392, P0393: 4 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

ALL:
Monitor runs whenever following DTCs are not stored None

P0365, P0390 (Verify pulse input):
Engine speed 600 rpm or more
Battery voltage 8 V or higher
Starter OFF
Ignition switch ON
Exhaust VVT sensor voltage 0.3 to 4.7 V
Exhaust VVT sensor range check low voltage fail (P0367, P0392) Not detected
Exhaust VVT sensor range check high voltage fail (P0368, P0393) Not detected

P0367, P0368, P0392, P0393 (Low voltage, High voltage):
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 2 seconds or more
Exhaust VVT sensor verify pulse input fail (P0365, P0390) Not detected
Battery voltage 8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

P0365, P0390
Exhaust VVT sensor signal No signal

P0367, P0392
Exhaust VVT sensor voltage Below 0.3 V

P0368, P0393
Exhaust VVT sensor voltage Higher than 4.7 V

COMPONENT OPERATING RANGE

VVT sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165014E04
0.593,3.888 0.923,4.065 0.330,0.177 10 D41 0.593,2.391 3.195,2.568 2.601,0.177 10 VVT Sensor (for Exhaust Side of Bank 1) 0.593,2.236 0.923,2.413 0.330,0.177 10 D40 0.593,4.044 3.263,4.220 2.670,0.177 10 VVT Sensor (for Exhaust Side of Bank 2) 1.442,1.186 1.750,1.339 0.308,0.152 10 VC2 1.442,2.847 1.750,2.999 0.308,0.152 10 VC2 1.848,1.277 1.990,1.454 0.142,0.177 10 3 4.845,1.277 5.081,1.454 0.236,0.177 10 66 4.849,1.659 5.085,1.836 0.236,0.177 10 69 4.849,2.042 5.085,2.219 0.236,0.177 10 68 1.428,1.572 1.753,1.724 0.326,0.152 10 EX+ 1.848,1.663 1.990,1.839 0.142,0.177 10 1 1.449,1.936 1.750,2.088 0.301,0.152 10 EX- 1.428,3.232 1.753,3.384 0.326,0.152 10 EX+ 1.449,3.596 1.750,3.749 0.301,0.152 10 EX- 5.127,1.186 5.598,1.339 0.471,0.152 10 VCV2 5.127,1.572 5.526,1.724 0.399,0.152 10 EV1+ 5.127,1.938 5.487,2.129 0.360,0.192 10 EV1- 4.849,3.322 5.085,3.498 0.236,0.177 10 64 4.849,3.704 5.085,3.881 0.236,0.177 10 65 5.127,3.234 5.526,3.387 0.399,0.152 10 EV2+ 5.127,3.6 5.487,3.792 0.360,0.192 10 EV2- 1.848,2.027 1.990,2.204 0.142,0.177 10 2 1.848,2.924 1.990,3.100 0.142,0.177 10 3 1.848,3.309 1.990,3.486 0.142,0.177 10 1 1.848,3.673 1.990,3.850 0.142,0.177 10 2 5.655,4.236 5.987,4.392 0.332,0.156 10 D74 5.655,4.372 6.022,4.527 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U151396E02
1.99,2.156 2.469,2.583 false 0.198,0.094 2.531,0.469 2.333,0.375 10 false Front view of wire harness connector: (to VVT Sensor) 0.271,1.875 0.573,2.073 0.302,0.198 10 false D40 0.271,2.219 0.563,2.396 0.292,0.177 10 false D41 0.177,2.552 1,2.75 0.823,0.198 10 false 1: for Bank 1 0.177,2.906 1,3.104 0.823,0.198 10 false 2: for Bank 2 2.51,2.563 2.833,2.771 0.323,0.208 10 false VC2 0.646,1.792 0.813,1.99 0.167,0.198 10 false *1 0.646,2.135 0.813,2.333 0.167,0.198 10 false *2

Disconnect the VVT sensor (for exhaust side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Bank 1
Tester Connection Switch condition Specified Condition
D40-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V

Bank 2
Tester Connection Switch condition Specified Condition
D41-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor (for exhaust side) connector.

A379422E02
0.323,1.26 0.719,1.5 0.396,0.24 0.333,1.573 0.729,1.813 0.396,0.24 4.625,0.802 5.021,1.042 0.396,0.24 1.76,1.656 2.688,1.167 true 1.938,1.708 2.667,1.969 true 4.01,1.719 3.802,2.25 true 4.063,1.719 4.24,2.24 true 4.281,1.719 4.667,2.26 true 4.365,1.719 5.115,2.302 true 0.688,0.094 3.01,0.458 2.323,0.365 10 false Front view of wire harness connector: (to VVT Sensor) 3.813,0.094 6.135,0.458 2.323,0.365 10 false Front view of wire harness connector: (to ECM) 0.396,1.302 0.76,1.5 0.365,0.198 10 false D40 0.396,1.604 0.76,1.802 0.365,0.198 10 false D41 0.792,1.302 1.156,1.5 0.365,0.198 10 false *1 0.792,1.604 1.156,1.802 0.365,0.198 10 false *2 2.76,1.052 3.344,1.24 0.583,0.188 10 false EX+ 2.74,1.885 3.323,2.073 0.583,0.188 10 false EX- 4.688,0.844 5.052,1.042 0.365,0.198 10 false D74 0.188,2 1.156,2.219 0.969,0.219 10 false *1: for Bank 1 0.188,2.333 1.156,2.552 0.969,0.219 10 false *2: for Bank 2 3.583,2.281 4,2.49 0.417,0.208 10 false EV2+ 4.094,2.292 4.521,2.5 0.427,0.208 10 false EV2- 4.604,2.292 5.021,2.5 0.417,0.208 10 false EV1- 5.146,2.302 5.563,2.51 0.417,0.208 10 false EV1+


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-1 (EX+) - D74-69 (EV1+) Always Below 1 Ω
D40-2 (EX-) - D74-68 (EV1-) Always Below 1 Ω
D41-1 (EX+) - D74-64 (EV2+) Always Below 1 Ω
D41-2 (EX-) - D74-65 (EV2-) Always Below 1 Ω
D40-1 (EX+) or D74-69 (EV1+) - Body ground Always 10 kΩ or higher
D40-2 (EX-) or D74-68 (EV1-) - Body ground Always 10 kΩ or higher
D41-1 (EX+) or D74-64 (EV2+) - Body ground Always 10 kΩ or higher
D41-2 (EX-) or D74-65 (EV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)
a.
A366136E02
0.469,1.667 1.01,1.875 0.542,0.208 10 false Normal 2.427,1.792 3.063,1.99 0.635,0.198 10 false Abnormal 1.542,1.563 2.271,1.771 0.729,0.208 10 false Clearance

Check the VVT sensor (for exhaust side) installation.

OK:

Sensor is installed correctly.




OK

4.INSPECT EXHAUST CAMSHAFT

NG

4.INSPECT EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

OK

6.REPLACE VVT SENSOR (FOR EXHAUST SIDE)

NG

ADJUST VALVE TIMING

6.REPLACE VVT SENSOR (FOR EXHAUST SIDE)
a.

Replace the VVT sensor (for exhaust side) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>VVT SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Refer to the confirmation driving pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No DTC is output A
P0365, P0367, P0368, P0390, P0392 or P0393 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B