1.REMOVE ENGINE WIRE
Engine LH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the camshaft position sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the air switching valve connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Remove the bolt and disconnect the 8 clamps.
Engine RH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Disconnect the air switching valve connector.
Disconnect the oil pressure sender gauge connector.
Disconnect the 6 clamps.
Engine Rear Side:
Disconnect the connector and clamp.
Remove the 4 bolts.
Remove the engine wire.
23801P
2.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
Remove the No. 1 fuel pipe (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).
23902
3.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY
Remove the No. 2 fuel tube (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).
25710
4.REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1)
Remove the 2 bolts.
Remove the 3 bolts, air switching valve assembly and gasket.
Be careful not to damage the installation surface of the gaskets.
25710
5.REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 2)
Remove the 2 bolts.
Remove the 3 bolts, air switching valve assembly and gasket.
Be careful not to damage the installation surface of the gaskets.
17364A
6.REMOVE NO. 4 AIR TUBE
Remove the bolt and wire harness clamp bracket.
Remove the bolt and No. 4 air tube.
17363Q
7.REMOVE NO. 3 AIR TUBE
Remove the bolt and wire harness clamp bracket.
Remove the bolt and No. 3 air tube.
8.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the hose and remove the 2 bolts and No. 3 water by-pass pipe.
16296
9.REMOVE NO. 8 WATER BY-PASS HOSE
Remove the No. 8 water by-pass hose.
16294
10.DISCONNECT NO. 11 WATER BY-PASS HOSE
25680
11.REMOVE EGR COOLER ASSEMBLY
11415A
12.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the 2 water drain cock plugs from the water drain cocks.
Remove the 2 water drain cocks from the cylinder block.
12361
13.REMOVE FRONT ENGINE MOUNTING INSULATOR RH
Remove the nut and mounting insulator.
12362A
14.REMOVE FRONT ENGINE MOUNTING INSULATOR LH
Remove the nut and mounting insulator.
12311
15.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Remove the 4 bolts and mounting bracket.
12315
16.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 4 bolts and mounting bracket.
23808
17.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH
23807
18.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH
83530
19.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
12614
20.REMOVE NO. 4 ENGINE COVER
12613
21.REMOVE NO. 3 ENGINE COVER
16261G
22.REMOVE NO. 1 WATER BY-PASS HOSE
23.REMOVE AIR TUBE SUB-ASSEMBLY RH
16206
24.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
16323
25.REMOVE WATER INLET HOUSING
16355
26.REMOVE FRONT WATER BY-PASS JOINT
16173
27.REMOVE WATER PUMP PULLEY
16603
28.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16307A
29.REMOVE FAN BRACKET SUB-ASSEMBLY
16620
30.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
12215
31.REMOVE SEPARATOR CASE
11212
32.REMOVE NO. 2 ENGINE COVER
Remove the No. 2 engine cover.
12611
33.REMOVE NO. 1 ENGINE COVER
Remove the No. 1 engine cover.
82121
34.REMOVE ENGINE WIRE
Disconnect the 4 knock sensor connectors.
Disconnect the 3 clamps. Then remove the engine wire.
16294
35.REMOVE NO. 11 WATER BY-PASS HOSE
Remove the No. 11 water by-pass hose.
89615
36.REMOVE KNOCK SENSOR
19500
37.REMOVE IGNITION COIL ASSEMBLY
Remove the 8 bolts and 8 ignition coils.
86011A
38.REMOVE NOISE FILTER
LH Side:
Remove the bolt and noise filter from the cylinder head cover.
RH Side:
Remove the bolt and noise filter from the cylinder head cover.