Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P050B  Cold Start Ignition Timing Performance  


DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).

The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature of lower than 50°C (122°F), the ECM checks the ignition timing at engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

NOTICE:

When the cable is disconnected from the negative battery terminal during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be stored with the ISC learning values cleared.


HINT:

The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A153342E53
2.51,3.188 1.948,4.125 1.948,4.125 1.771,4.125 false 4.625,2.438 4.906,2.76 4.906,2.76 5.083,2.76 false 4.635,1.99 5.063,1.323 5.063,1.323 5.302,1.323 false 1.438,0.813 2.354,0.99 0.917,0.177 10 false Ignition Timing 1.542,1.208 2.177,1.385 0.635,0.177 10 false Advanced 1.594,3.052 2.177,3.229 0.583,0.177 10 false Retarded 1.542,2.063 2.177,2.24 0.635,0.177 10 false Threshold 0.917,4.042 1.781,4.229 0.865,0.188 10 false Engine Start 2.698,3.385 2.854,3.563 0.156,0.177 10 false 3 3.75,3.385 3.917,3.563 0.167,0.177 10 false 10 3.573,3.667 3.896,3.844 0.323,0.177 10 false Time 4.813,3.354 5.458,3.531 0.646,0.177 10 false (Seconds) 5.146,2.656 6.688,2.833 1.542,0.177 10 false Pass Condition Detected 3.708,1.594 4.323,1.771 0.615,0.177 10 false 8 or more 5.365,1.229 6.396,1.406 1.031,0.177 10 false P050B Detected 0.208,0.146 1.885,0.354 1.677,0.208 10 false P050B Detection Logic: 2.573,4.135 6,4.313 3.427,0.177 10 false Engine Coolant Temperature: -10 to 50°C (14 to 122°F)

DTC No. DTC Detection Condition Trouble Area
P050B Insufficient ignition timing retard at cold start (2 trip detection logic)
·

Throttle with motor body assembly

·

Mass air flow meter

·

PCV system

·

Air cleaner filter element sub-assembly

·

Intake system

·

VVT system

·

EGR valve assembly

·

ECM

·

Wire harness or connector



MONITOR STRATEGY

Related DTCs P050B: Cold start ignition timing performance
Required Sensors/Components (Main) Throttle with motor body assembly
Required Sensors/Components (Related) Mass air flow meter
Engine Coolant Temperature (ECT) sensor
Frequency of Operation Once per driving cycle
Duration 10 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
Battery voltage 8 V or more
Time after engine start 3 seconds or more
Starter OFF
ECT at engine start -10°C (14°F) or more
ECT -10 to 50°C (14 to 122°F)
Engine idling time 3 seconds or more
Fuel-cut OFF
Vehicle speed Less than 3 km/h (1.875 mph)
Atmospheric pressure 76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS

Accumulated time when ignition timing retard is cut off 8 seconds or more

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

7.

Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).

8.

Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.

9.

Idle the engine for 1 minute or more.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

11.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P050B.

14.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


15.

If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [B].

16.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

DTC P050B may be set when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.

Symptom Factor Trouble Area
Low idle speed when engine is cold (immediately after engine start) Excessive engine friction
·

Engine oil deterioration

·

Drive belt tension

·

A/C compressor

·

Generator

·

Vane pump


Rough idle when engine is cold (immediately after engine start) Abnormal combustion Fuel quality

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the pending DTCs.

Result
Result Proceed to
DTC P050B is output A
DTC P050B and other DTCs are output B

HINT:

If any DTCs other than P050B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (FUEL TRIM)

B

2.READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.


a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.


e.

Read the values displayed on the Techstream.


f.

Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

OK:

Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.




OK

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE BODY)

NG

7.CHECK PCV HOSE
3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE BODY)
a.

Check for deposits around the throttle valve and check the throttle valve condition.

OK:

No deposits around throttle valve and throttle valve moves smoothly.




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

6.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.INSPECT EGR VALVE ASSEMBLY
5.INSPECT EGR VALVE ASSEMBLY

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

17.REPLACE EGR VALVE ASSEMBLY
6.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Repair or replace the throttle with motor body assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle with motor body assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK PCV HOSE
a.

Check the PCV hose connections (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

8.CHECK INTAKE SYSTEM

NG

14.REPAIR OR REPLACE PCV HOSE
8.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>1UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leak in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

15.REPAIR OR REPLACE INTAKE SYSTEM
9.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.




OK

10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

12.PERFORM ACTIVE TEST USING TECHSTREAM

NG

11.INSPECT EGR VALVE ASSEMBLY
11.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

12.PERFORM ACTIVE TEST USING TECHSTREAM

NG

17.REPLACE EGR VALVE ASSEMBLY
12.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Operate the VVT system through the Active test, and check if the VVT system is operating normally.

i.

Perform the Active Test, referring to DTC P0011 inspection procedure (VVT system for intake side) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0011).


ii.

Perform the Active Test, referring to DTC P0014 inspection procedure (VVT system for exhaust side) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0014).




OK

13.READ VALUE USING TECHSTREAM (MAF)

NG

18.CHECK AND REPAIR VVT SYSTEM
13.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.


d.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


e.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)




OK

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

20.CHECK HARNESS AND CONNECTOR
14.REPAIR OR REPLACE PCV HOSE
a.

Repair or replace the PCV hose.



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).

HINT:

Perform "Inspection After Repair" after repairing or replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.

HINT:
·

Refer to DTC P0011 Inspection Procedure (VVT system for intake side) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0011).

·

Refer to DTC P0014 Inspection Procedure (VVT system for exhaust side) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0014).





NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:

In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P050B.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P050B is output)
B



A

B

20.CHECK HARNESS AND CONNECTOR
20.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
21.CHECK WHETHER DTC OUTPUT RECURS
NOTICE:

In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P050B.


k.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P050B is output)
A
NORMAL
(DTC is not output)
B



A

22.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

22.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
U151537E02
1.521,1.531 0.833,1.958 false 1.76,1.521 2.448,1.927 false 1.469,3.865 1.75,4.406 false 1.385,3.865 1.031,4.406 false 0.458,1.396 0.729,1.573 0.271,0.177 10 false D7 0.49,1.875 0.833,2.052 0.344,0.177 10 false E2G 2.5,1.844 2.781,2.083 0.281,0.24 10 false VG 0.125,2.917 0.448,3.094 0.323,0.177 10 false D74 1.667,4.427 2.073,4.625 0.406,0.198 10 false E2G 0.917,4.427 1.135,4.604 0.219,0.177 10 false VG 0.156,0.094 2.49,0.438 2.333,0.344 10 false Front view of wire harness connector: (to MAF Meter) 0.146,2.167 2.479,2.51 2.333,0.344 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VG) - D74-74 (VG) Always Below 1 Ω
D7-2 (E2G) - D74-75 (E2G) Always Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground Always 10 kΩ or higher




OK

23.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 13 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:

In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P050B.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P050B is output)
B



A

END

B