Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0014  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)  P0015  Camshaft Position "B" - Timing Over-Retarded (Bank 1)  P0024  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)  P0025  Camshaft Position "B" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

HINT:

If DTC P0014, P0015, P0024 or P0025 is present, check the VVT (Variable Valve Timing) system.


The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

A192077E02
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.758,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.049,5.101 1.166,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0014
P0024
Exhaust valve timing is not adjusted in valve timing advance range
(2 trip detection logic)
·

Valve timing

·

Oil control valve (OCV) (for exhaust side of bank 1, 2)

·

OCV filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0015
P0025
Exhaust valve timing is not adjusted in valve timing retard range
(1 trip detection logic)
·

Valve timing

·

OCV (for exhaust side of bank 1, 2)

·

OCV filter

·

Camshaft timing exhaust gear assembly

·

ECM



MONITOR DESCRIPTION

1.

The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, Oil Control Valve (OCV) and VVT controller.

2.

The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.

Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After the above condition 1 is met, the camshaft timing oil control valve is forcibly activated for 10 seconds.



DTCs P0014 and P0024 (Advanced Cam Timing) are subject to 2 trip detection logic.

DTCs P0015 and P0025 (Retarded Cam Timing) are subject to 1 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.

MONITOR STRATEGY

Related DTCs P0014: Advanced camshaft timing (for Bank 1)
P0015: Retarded camshaft timing (for Bank 1)
P0024: Advanced camshaft timing (for Bank 2)
P0025: Retarded camshaft timing (for Bank 2)
Required sensors/Components (Main) VVT OCV and VVT Actuator
Required sensors/Components (Related) Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor
Frequency of operation Continuous
Duration Within 10 seconds
MIL operation Advanced camshaft timing: 2 driving cycles
Retarded camshaft timing: Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs are not present P0013, P0023 (Exhaust VVT oil control valve)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
Battery voltage 11 V or more
Engine RPM 500 to 4000 rpm
Engine coolant temperature 75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS

Advanced Camshaft Timing
Both conditions are met: -
Deviation of actual valve timing and target valve timing More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing No change at advanced valve timing

Retarded Camshaft Timing
Both conditions are met: -
Deviation of actual valve timing and target valve timing More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing No change at retarded valve timing

CONFIRMATION DRIVING PATTERN

A232050E10
1.361,2.351 1.596,2.498 0.235,0.147 10 [A] 1.88,2.062 2.114,2.208 0.235,0.147 10 [B] 3.012,1.001 3.247,1.148 0.235,0.147 10 [C] 4.049,2.316 4.284,2.463 0.235,0.147 10 [D] 4.285,3.14 4.519,3.287 0.235,0.147 10 [E] 5.445,2.218 5.680,2.365 0.235,0.147 10 [F]* 6.618,2.3 6.852,2.446 0.235,0.147 10 [G] 6.832,3.154 7.067,3.301 0.235,0.147 10 [H] 0.133,2.309 1.104,2.641 0.971,0.332 10 Ignition Switch ON 0.712,2.057 1.099,2.241 0.387,0.184 10 Idling 0.027,1.09 1.145,1.434 1.119,0.343 10 Approximately 60 km/h (37 mph) 0.17,0.376 1.123,0.541 0.952,0.165 10 Vehicle Speed 1.618,2.767 2.422,2.960 0.804,0.193 10 Warming up 2.561,2.776 3.805,2.923 1.244,0.147 10 10 minutes or more 2.552,3.393 3.847,3.567 1.295,0.174 10 3 minutes or more 6.723,2.596 6.33,3.458 6.33,3.458 6.246,3.458 false 4.159,2.617 3.836,3.479 3.836,3.479 3.766,3.479 false 2.379,0.025 7.035,0.542 4.656,0.517 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5.004,3.379 6.195,3.553 1.191,0.174 10 3 minutes or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0014, P0015, P0024 or P0025.

13.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a target amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.



19.

Perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Advanced Timing Over
(Valve Timing Out of Specified Range)
Retarded Timing Over
(Valve Timing Out of Specified Range)
Bank 1 P0014 P0015
Bank 2 P0024 P0025

·

If DTC P0014 or P0015 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0024 or P0025 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0014, P0015, P0024 or P0025 A
P0014, P0015, P0024 or P0025 and other DTCs B

HINT:

If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).


e.

Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

OK:
Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN OR JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.



d.

Warm up the engine.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Read the output pending DTCs using the Techstream.

OK:

No pending DTC output.




OK

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN OR JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN OR JUMPED TOOTH)
A214700E09
0.542,3.323 0.833,4.208 0.833,4.208 1.396,3.427 false 5.469,3.646 5.813,4.219 5.813,4.219 6.49,3.427 false 0.615,2 0.427,2 0.427,2 0.615,2.885 false 1.833,2.406 1.896,2.406 1.896,2.406 1.75,2.771 false 0.573,0.26 0.448,0.26 0.448,0.26 0.552,0.844 false 1.604,0.271 1.792,0.271 1.792,0.271 1.667,0.75 false 5.615,0.26 5.469,0.26 5.469,0.26 5.563,0.771 false 6.677,0.281 6.854,0.281 6.854,0.281 6.719,0.896 false 5.292,2.448 5.188,2.448 5.188,2.448 5.427,2.927 false 6.531,2.104 6.729,2.104 6.729,2.104 6.563,2.896 false 0.594,0.188 1.635,0.365 1.042,0.177 10 false Alignment Mark 5.656,0.188 6.708,0.354 1.052,0.167 10 false Alignment Mark 0.583,4.24 1.771,4.396 1.188,0.156 10 false Knock Pin Position 5.438,4.24 6.625,4.396 1.188,0.156 10 false Knock Pin Position 0.667,1.927 1.771,2.115 1.104,0.188 10 false Approximately 2° 0.667,2.323 1.854,2.51 1.188,0.188 10 false Approximately 16° 5.344,2.396 6.531,2.583 1.188,0.188 10 false Approximately 32° 5.344,2.021 6.531,2.208 1.188,0.188 10 false Approximately 18°

a.

Remove the cylinder head cover LH and RH.


b.

Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.


c.

Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

HINT:
·

If the alignment marks are not as shown, turn the crankshaft one revolution clockwise.

·

If the result is not as specified, check mechanical parts related to valve timing for looseness in the timing chain, jumped teeth, etc.



OK:

Alignment marks on camshaft timing gears are aligned as shown in the illustration.




OK

5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (OCV)

NG

5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (OCV)
a.
A159175E07
0.057,0 2.755,0.336 2.698,0.336 10 Component without harness connected: (OCV for Exhaust Camshaft) 0.598,1.161 1.442,1.345 0.843,0.184 10 Valve moves

Remove the OCV (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω



c.

Apply positive (+) battery voltage to terminal 1 and negative (-) battery voltage to terminal 2. Check the valve operation.

OK:

Valve moves quickly.




OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.




OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

CLEAN OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.



d.

Warm up the engine.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Read the output pending DTCs using the Techstream.

OK:

No pending DTC output.


HINT:

DTC P0014, P0015, P0024 or P0025 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




OK

END

NG