Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1 and VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The intake camshaft has a sensor plate with 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the gear rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0340
P0345
No VVT sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side of bank 1, 2) circuit

·

VVT sensor (for intake side of bank 1, 2)

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM


P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side of bank 1, 2) circuit

·

VVT sensor (for intake side of bank 1, 2)

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM


P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor (for intake side of bank 1, 2) circuit

·

VVT sensor (for intake side of bank 1, 2)

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM



A217926E02
0.218,1.183 0.448,1.348 0.230,0.165 10 NE 0.145,1.733 0.449,1.885 0.304,0.151 10 VV1 0.149,2.105 0.448,2.251 0.299,0.145 10 VV2 2.85,1.275 3.186,1.424 0.336,0.149 10 GND 2.85,2.195 3.186,2.344 0.336,0.149 10 GND 2.85,1.818 3.186,1.967 0.336,0.149 10 GND 1.1,2.509 2.021,2.650 0.921,0.141 10 20 msec./DIV. 2.685,0.797 3.249,0.953 0.563,0.156 10 5 V/DIV. 0.102,0.078 2.419,0.234 2.318,0.156 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-110 (NE+) - D74-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-92 (VV1+) - D74-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-87 (VV2+) - D74-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

VV1 and VV2 are the VVT sensor signals, and NE is the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P0340: VVT position sensor (for Bank 1) verify pulse input
P0342: VVT position sensor (for Bank 1) range check (low voltage)
P0343: VVT position sensor (for Bank 1) range check (high voltage)
P0345: VVT position sensor verify pulse input (for Bank 2)
P0347: VVT position sensor (for Bank 2) range check (low voltage)
P0348: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main) VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration P0340, P0345: 5 seconds
P0342, P0343, P0347, P0348: 4 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0340, P0345 (Verify pulse input):
Engine speed 600 rpm or more
Battery voltage 8 V or higher
Starter OFF
Ignition switch ON
Camshaft position sensor voltage 0.3 to 4.7 V
VVT sensor range check low voltage fail (P0342, P0347) Not detected
VVT sensor range check high voltage fail (P0343, P0348) Not detected

P0342, P0343, P0347, P0348 (Low voltage, High voltage):
Starter OFF
Ignition switch ON
Ignition switch ON and time after ignition switch is off to ON 2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345) Not detected
Battery voltage 8 V or Higher

TYPICAL MALFUNCTION THRESHOLDS

P0340, P0345 (Verify pulse input):
VVT sensor signal No signal

P0342, P0347 (Low voltage):
VVT sensor voltage Below 0.3 V

P0343, P0348 (High voltage):
VVT sensor voltage Higher than 4.7 V

COMPONENT OPERATING RANGE

VVT sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.


13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165014E03
0.593,3.888 0.923,4.065 0.330,0.177 10 D39 0.593,2.391 3.082,2.568 2.489,0.177 10 VVT Sensor (for Intake Side of Bank 1) 0.593,2.236 0.923,2.413 0.330,0.177 10 D37 0.593,4.044 3.083,4.220 2.490,0.177 10 VVT Sensor (for Intake Side of Bank 2) 1.529,1.186 1.750,1.339 0.222,0.152 10 VC 1.848,1.277 1.990,1.454 0.142,0.177 10 3 4.845,1.277 5.081,1.454 0.236,0.177 10 66 4.849,1.659 5.085,1.836 0.236,0.177 10 92 4.849,2.042 5.085,2.219 0.236,0.177 10 91 1.354,1.572 1.753,1.724 0.399,0.152 10 VVL+ 1.848,1.663 1.990,1.839 0.142,0.177 10 1 1.385,1.936 1.749,2.088 0.364,0.152 10 VVL- 5.127,1.186 5.598,1.339 0.471,0.152 10 VCV2 5.127,1.572 5.526,1.724 0.399,0.152 10 VV1+ 5.127,1.938 5.487,2.129 0.360,0.192 10 VV1- 4.849,3.322 5.085,3.498 0.236,0.177 10 87 4.849,3.704 5.085,3.881 0.236,0.177 10 88 5.127,3.234 5.526,3.387 0.399,0.152 10 VV2+ 5.127,3.6 5.487,3.792 0.360,0.192 10 VV2- 1.848,2.027 1.990,2.204 0.142,0.177 10 2 1.529,2.833 1.750,2.985 0.222,0.152 10 VC 1.848,2.924 1.990,3.100 0.142,0.177 10 3 1.354,3.218 1.753,3.370 0.399,0.152 10 VVR+ 1.848,3.309 1.990,3.486 0.142,0.177 10 1 1.385,3.582 1.749,3.735 0.364,0.152 10 VVR- 1.848,3.673 1.990,3.850 0.142,0.177 10 2 5.655,4.236 5.987,4.392 0.332,0.156 10 D74 5.655,4.372 6.022,4.527 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
U151398E01
0.04,0.004 2.372,0.354 2.332,0.350 10 Front view of wire harness connector: (to VVT Sensor) 0.263,1.585 0.548,1.732 0.286,0.147 10 D37 0.263,1.929 0.548,2.075 0.286,0.147 10 D39 0.653,1.577 0.809,1.752 0.156,0.174 10 *1 0.653,1.928 0.809,2.102 0.156,0.174 10 *2 2.508,2.429 2.733,2.585 0.225,0.156 10 VC 0.211,2.594 1.093,2.750 0.883,0.156 10 *1: for Bank 1 0.211,2.979 1.093,3.135 0.883,0.156 10 *2: for Bank 2 1.981,2.217 2.485,2.504 false

a.

Disconnect the VVT sensor (for intake side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)
a.

Disconnect the VVT sensor (for intake side) connector.

A379422E01
0.323,1.26 0.719,1.5 0.396,0.24 0.333,1.573 0.729,1.813 0.396,0.24 4.625,0.802 5.021,1.042 0.396,0.24 1.76,1.656 2.688,1.167 false 1.938,1.708 2.667,1.969 false 4,1.792 3.802,2.25 false 4.063,1.781 4.24,2.24 false 4.281,1.792 4.677,2.26 false 4.354,1.792 5.125,2.292 false 0.688,0.094 3.01,0.458 2.323,0.365 10 false Front view of wire harness connector: (to VVT Sensor) 3.813,0.094 6.135,0.458 2.323,0.365 10 false Front view of wire harness connector: (to ECM) 0.396,1.302 0.76,1.5 0.365,0.198 10 false D37 0.396,1.604 0.76,1.802 0.365,0.198 10 false D39 0.792,1.302 1.156,1.5 0.365,0.198 10 false *1 0.792,1.604 1.156,1.802 0.365,0.198 10 false *2 2.76,1.052 3.344,1.24 0.583,0.188 10 false VVL+*1 2.75,1.219 3.333,1.406 0.583,0.188 10 false VVR+*2 2.74,1.885 3.323,2.073 0.583,0.188 10 false VVL-*1 2.74,2.042 3.323,2.229 0.583,0.188 10 false VVR-*2 4.688,0.844 5.052,1.042 0.365,0.198 10 false D74 0.188,2 1.156,2.219 0.969,0.219 10 false *1: for Bank 1 0.188,2.333 1.156,2.552 0.969,0.219 10 false *2: for Bank 2 3.583,2.281 4,2.49 0.417,0.208 10 false VV2+ 4.094,2.292 4.521,2.5 0.427,0.208 10 false VV2- 4.604,2.292 5.021,2.5 0.417,0.208 10 false VV1- 5.146,2.302 5.563,2.51 0.417,0.208 10 false VV1+


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-1 (VVL+) - D74-92 (VV1+) Always Below 1 Ω
D37-2 (VVL-) - D74-91 (VV1-) Always Below 1 Ω
D39-1 (VVR+) - D74-87 (VV2+) Always Below 1 Ω
D39-2 (VVR-) - D74-88 (VV2-) Always Below 1 Ω
D37-1 (VVL+) or D74-92 (VV1+) - Body ground Always 10 kΩ or higher
D37-2 (VVL-) or D74-91 (VV1-) - Body ground Always 10 kΩ or higher
D39-1 (VVR+) or D74-87 (VV2+) - Body ground Always 10 kΩ or higher
D39-2 (VVR-) or D74-88 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE SIDE)
a.
BR03795E98
2.163,1.53 2.360,1.731 0.197,0.201 10 *c 0.49,1.765 0.757,1.973 0.267,0.208 10 *a 2.673,1.765 2.940,1.973 0.267,0.208 10 *b 2.833,1.978 3.414,2.144 0.581,0.165

Check the VVT sensor (for intake side) installation.

OK:

Sensor is installed correctly.




OK

4.INSPECT INTAKE CAMSHAFT (TEETH)

NG

4.INSPECT INTAKE CAMSHAFT (TEETH)
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

OK

6.REPLACE VVT SENSOR (FOR INTAKE SIDE)

NG

ADJUST VALVE TIMING

6.REPLACE VVT SENSOR (FOR INTAKE SIDE)
a.

Replace the VVT (for intake side) sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>VVT SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear DTCs.


e.

Refer to the confirmation driving pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0340, P0342, P0343, P0345, P0347 or P0348 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B